Manual Pelco C3420M

16 pages 0.44 mb
Download

Go to site of 16

Summary
  • Pelco C3420M - page 1

    ® INSTALLATION Heavy-Duty Spectra ® IV Series C3420M (8/06) Pendant Back Box ...

  • Pelco C3420M - page 2

    2 C3420M (8/06) Installation 1 3 2 ...

  • Pelco C3420M - page 3

    C3420M (8/0 6) 3 1. Install the mount for th e pendant dome . Refer to the instruct ions supplied with the mount. If the moun t is outdoors, make sure it is properly se aled to keep moisture out. 2. Open t he hinged do or to the back box. P ush the tab lock towards the wall o f the unit and lift t he door op en. Pull wiring into the back box. Refer ...

  • Pelco C3420M - page 4

    4 C3420M (8/06) 5 4 VIDEO UTP+ UTP- RX- RX- TX- TX- PWR- PWR+ GND AUX2 GND GND NO NC COM 7 6 5 4 3 2 1 ALARMS AUX1 ...

  • Pelco C3420M - page 5

    C3420M (8/0 6) 5 4. Connect wiring to the circuit board inside the back box. Whe n finished, clos e the door to th e back box and turn o n the power . The green LED will light. NOTES: • Aux 1: Maximum 2 A at low voltage (<40 V) Aux 2: Maximum 30 mA at 32 VDC • If you are u sing both u nshielded twi ste d pair (UTP) wiring and a transla tor b ...

  • Pelco C3420M - page 6

    6 C3420M (8/06) BARREL LOCK CENTER PIN   SWITCH 1 AND 2 6 7 8 9 ...

  • Pelco C3420M - page 7

    C3420M (8/0 6) 7 6. Configu re DIP switc hes SW1 and SW2 lo cated on th e top of the dome drive. For DIP switch settin gs, refer to the labels locat ed on the top of the dome dr ive or to t he Switch Settings section of this manual. NOTE: When co nnecting more than on e Spectra dome to a single controller , termin ate the unit farth est from the co ...

  • Pelco C3420M - page 8

    8 C3420M (8/06) T roubleshooting If your dome do es not power up proper ly after installati on, use the following steps. 1. Check the fuse on the circuit board inside the ba ck box for continuity . Replace the fuse if needed. 2. Check th e wiring with a volt meter to ensure p r oper voltage is being received in to the back box. If your dome powers ...

  • Pelco C3420M - page 9

    C3420M (8/0 6) 9 Switch Settings WAR N I NG : If you are using D-ty pe or P-type control, your system may no t operate if the baud rate and address switches are not set cor rectly . The switches ar e set at t he factory at the defau lts for D-t ype control (2400 baud and address 1). T able D. Switch Settings for SW2 Special Sy stems S w i t c h N u ...

  • Pelco C3420M - page 10

    10 C3420M (8/06) T able E. Switch Settings for SW1, P-T ype Control NOTE: For Coaxitron controls, SW1 is not us ed; set all switches OFF . For D-type con trol systems, refer to T abl e F . T able F . Switch Settings for SW1, D-T ype Control NOTE: For Coaxitron controls, SW1 is not used; set all switches OFF . For P-t ype control systems, re fer to ...

  • Pelco C3420M - page 11

    C3420M (8/0 6) 11 SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 71 ON ON ON OFF OFF OFF ON OFF 72 OFF OFF OFF ON OFF OFF ON OFF 73 ON OFF OFF ON OFF OFF ON OFF 74 OFF ON OFF ON OFF OFF ON OFF 75 ON ON OFF ON OFF OFF ON OFF 76 OFF OFF ON ON OFF OFF ON OFF 77 ON OFF ON ON OFF OFF ON OFF 78 OFF ON ON ON OFF OFF ON OFF ...

  • Pelco C3420M - page 12

    12 C3420M (8/06) SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 151 ON ON ON OFF ON OFF OFF ON 152 OFF OFF OFF ON ON OFF OFF ON 153 ON OFF OFF ON ON OFF OFF ON 154 OFF ON OFF ON ON OFF OFF ON 155 ON ON OFF ON ON OFF OFF ON 156 OFF OFF ON ON ON OFF OFF ON 157 ON OFF ON ON ON OFF OFF ON 158 OFF ON ON ON ON OFF OFF ON ...

  • Pelco C3420M - page 13

    C3420M (8/0 6) 13 SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 223 ON ON ON ON ON OFF ON ON 224 OFF OFF OFF OFF OFF ON ON ON 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON 227 ON ON OFF OFF OFF ON ON ON 228 OFF OFF ON OFF OFF ON ON ON 229 ON OFF ON OFF OFF ON ON ON 230 OFF ON ON OFF OFF ON ON ON 2 ...

  • Pelco C3420M - page 14

    14 C3420M (8/06) Weight (approximate) Back Box Pendant 4.45 lb (2.02 kg) Environmental Pendant 4.75 lb (2.1 5 kg) Dome Drive 3.3 lb (1.48 kg) Lower Dome Pendant 1.83 lb (0.83 kg) Pendant with Ca ge 3.83 lb (1.74) ELECTRICAL (Dome Drive Only) Input V oltag e 18-32 V AC; 24 VAC nomina l 22-27 VDC; 24 VDC nominal Input Power 24 V AC 23 V A nominal (in ...

  • Pelco C3420M - page 15

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRA NTY Pelco will r epair or repla ce, without charge, any merchandise p roved defectiv e in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are a s noted below: • Five years on FR/F T/FS Series fiber opt ic products and TW3 000 Series unshielded ...

  • Pelco C3420M - page 16

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Canada | Finland | France | Italy | Russia | Singapore | Spain | Sweden | The Netherl ands | United Ar ab Emirat es | United Kingdom | U ...

Manufacturer Pelco Category Landscape Lighting

Documents that we receive from a manufacturer of a Pelco C3420M can be divided into several groups. They are, among others:
- Pelco technical drawings
- C3420M manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco C3420M
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco C3420M.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco C3420M, service manual, brief instructions and user manuals Pelco C3420M. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco C3420M.

Similar manuals

A complete manual for the device Pelco C3420M, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco C3420M by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco C3420M.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco C3420M - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco C3420M, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco C3420M, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco C3420M - which should help us in our first steps of using Pelco C3420M
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco C3420M
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco C3420M in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco C3420M?

Use the form below

If you did not solve your problem by using a manual Pelco C3420M, ask a question using the form below. If a user had a similar problem with Pelco C3420M it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)