English dropdown-ico

Manual Makita 3705

19 pages 0.85 mb
Download

Go to site of 19

Summary
  • Makita 3705 - page 1

    Trimmer 14' 1/4" MODEL 3705 23,000 215 mm (8 7/16") 1 8 kg (4 Ibs) INSTRUCTION MANUAL DOUBLE INSULATION SPEC IF I CAT IONS Overall length Net weight Collet chuck No load speed capacity 1 (RPM) ...

  • Makita 3705 - page 2

    IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CO ...

  • Makita 3705 - page 3

    14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only ext ...

  • Makita 3705 - page 4

    ADDITIONAL SAFETY RULES 1. Wear hearing protection during extended periods of operation. 2. Handle the bits very carefully. 3. Check the bit carefully for cracks or damage before operation. Replace cracked or damaged bit immediately. 4. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation. 5. Hold the tool firml ...

  • Makita 3705 - page 5

    Installing or removing trimmer bit CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the bit. Use the hex wrench to loosen the clamp bolt and lower the tool base. lnser the bit all the way into the collet cone and tighten the collet nut securely with the two wrenches. To remove the bit, follow the in ...

  • Makita 3705 - page 6

    Switch action To start the tool, move the switch lever to the “ON” position. To stop, move the switch lever to the “OFF” position. Operation *Set the tool base on the workpiece to be cut without the bit making any contact. Then turn the tool on and wait until the bit attains full speed. Move the tool forward over the workpiece surface, keep ...

  • Makita 3705 - page 7

    Straight guide (Optional accessory) The straight guide is effectively used for straight cuts when chamfering or grooving. Install the straight guide on the guide holder with the wing bolt. Then use the hex wrench to loosen the bolts on the tool base and insert the guide holder into the grooves in the tool base. Adjust the dis- tance between the bit ...

  • Makita 3705 - page 8

    Trimmer guide (Optional accessory) Trimming, curved cuts in veneers for fur- niture and the like can be done easily with the trimmer guide. The guide roller rides the curve and assures a fine cut. Install the trimmer guide on the guide holder with the wing bolt. Then use the hex wrench to loosen the bolts on the tool base and insert the guide holde ...

  • Makita 3705 - page 9

    Templet guide The templet guide provides a sleeve through which the bit passes, allowing use of the trimmer with templet patterns. I To install the templet guide, loosen the screws on the tool base, insert the templet guide and then tighten the screws. Templet guide 7 Fix the templet to the workpiece. Move the tool with the templet guide sliding al ...

  • Makita 3705 - page 10

    MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be r ...

  • Makita 3705 - page 11

    ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Templet guide Part No. 321912-7 0 Straight g ...

  • Makita 3705 - page 12

    Bits STRAIGHT - Single Flute HIGH SPEED STEEL PART NO. A B C D E 733232-6A 118 5/16 1.118 1 /4 1-518 STRAIGHT - 2 Flute iDi- CARBIDE TIPPED PART NO. A B C D E 733003-2A 3/16 7116 1-318 114 2 HINGE MORTISING CARBIDE TIPPED I PARTNO. A B C D E 733006-9A 112 112 1-1116 114 1-1 311 6 VEINING - Single Flute SOLID CARBIDE PART NO. A B C D E 733007-8A 311 ...

  • Makita 3705 - page 13

    ROUND NOSE CARBIDE TIPPED PART NO. A B C D E 733008-2A 1 14 15132 1~1 I4 114 1-718 733008-4A 318 9116 1-1 14 114 2 CORE BOX HIGH SPEED STEEL PART NO. A 8 C D E 733238-2A 1 I4 114 1-3116 1 I4 1-1 /2 VEE GROOVING -pr CARBIDE TIPPED I PARTNO A 8 C D E 01 733009-2A 318 112 1.3116 114 2 9 0" 733009~4A 518 314 15/16 114 2 90" 14" DOVETAIL ...

  • Makita 3705 - page 14

    PANEL PILOT HIGH SPEED STEEL PART NO A B C D E 733236 OA 1 14 314 1 114 2 7116 CORNER ROUNDING HIGH SPEED STEEL Solid Pilof PARTNO A, AI B C D E R 733240 2A 11/16 3/16 112 1 114 1 314 114 COVE HIGH SPEED STEEL - Solid Pilot PARTNO. A) A2 6 C D E R 733242-6A 11116 3/16 112 1 114 1-314 114 FLUSH TRIMMER - Self Piloting SOLID CARBIDE PART NO A B C D E ...

  • Makita 3705 - page 15

    7" BEVEL TRIMMER - Self-Piloting PART NO A B C D E 7331 28 2A 3116 114 11/16 114 19/16 2 FLUTE FLUSH TRIMMER CARBIDE TIPPED PART NO A B C D E 7331 28-9A 1 /2 112 1114 114 2-1/16 REPLACEMENT BEARING ~ NO 733132-4A COMBINATION FLUSH/22" BEVEL TRIMMER ilJk CARBIDE TIPPED PART NO A BI 82 C D E 733128 6A 7/16 112 3/16 1 114 1/4 1 314 3 FLUTE F ...

  • Makita 3705 - page 16

    FLUTE FLUSH REPLACEMENT CUTTER SOLID CARBIDE PART NO. A B D 733129-6A 5/8 318 114 FOR FLUSH TRIMMER ASSEMBLY NO. 733129-2A I 114" REPLACEMENT ARBOR I PARTNO A B C D El I 733131-2A 518 318 1-114 114 2-318 I I FOR FLUSH TRIMMER ASSEMBLY NO 733129-2A I BALL BEARING PILOT I PARTNO D, D7 I 733132-4A 112 OD 3/16 I D 733132 6A 518 0 D 114 ID 16 ...

  • Makita 3705 - page 17

    oct 09 87 us 114" TRIMMER Model 3705 Note The switch, noise suppressor and other part configurations may differ from country to country 17 ...

  • Makita 3705 - page 18

    MODEL 3705 I;"," DESCRIPTION Mar 31 86 US ,,!& DESCRIPTION MACE 1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 I7 18 19 11 22 23 24 25 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 2 2 1 3 1 2 1 - Clirrl Redr Cover Curd Guard Pan Head Srrew M4x14 IWifh WazhPrl Strain Relipf Mom Redr tlowng FIELD ASSEMBLY Drsvr Shall Ball Bearing 6000LB Ring 10 Ball Bedrinq 6 ...

  • Makita 3705 - page 19

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh ...

Manufacturer Makita Category Trimmer

Documents that we receive from a manufacturer of a Makita 3705 can be divided into several groups. They are, among others:
- Makita technical drawings
- 3705 manuals
- Makita product data sheets
- information booklets
- or energy labels Makita 3705
All of them are important, but the most important information from the point of view of use of the device are in the user manual Makita 3705.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Makita 3705, service manual, brief instructions and user manuals Makita 3705. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Makita 3705.

Similar manuals

A complete manual for the device Makita 3705, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Makita 3705 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Makita 3705.

A complete Makita manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Makita 3705 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Makita 3705, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Makita 3705, that we can find in the current document
3. Tips how to use the basic functions of the device Makita 3705 - which should help us in our first steps of using Makita 3705
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Makita 3705
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Makita 3705 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Makita 3705?

Use the form below

If you did not solve your problem by using a manual Makita 3705, ask a question using the form below. If a user had a similar problem with Makita 3705 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)