English dropdown-ico

Manual Cisco Systems 17053

27 pages 0.06 mb
Download

Go to site of 27

Summary
  • Cisco Systems 17053 - page 1

    Troubleshooting Cisco Catalyst Switches to NIC Compatibility Issues Document ID: 17053 Introduction Prerequisites Requirements Components Used Conventions Background Information Purpose Why Do Autonegotiation and Compatibility Issues Exist? General Troubleshooting for 10/100/1000 Mbps NICs Autonegotiation Valid Configuration Table EtherChannel and ...

  • Cisco Systems 17053 - page 2

    Components Used This document is not restricted to specific software and hardware versions. Conventions Refer to Cisco Technical Tips Conventions for more information on document conventions. Background Information Purpose This document discusses how to troubleshoot these issues: Autonegotiation • Physical Connectivity • Port Errors (Data Link ...

  • Cisco Systems 17053 - page 3

    performance−related issues. The most common problems with NIC issues deal with speed and duplex configuration. Table 1 summarizes all possible settings of speed and duplex for FastEthernet NICs and switch ports. Note: This section is only applicable for 10/100/1000 Mbps (1000BASE−T) NICs, and not 1000BASE−X NICs. Table 1Autonegotiation Val ...

  • Cisco Systems 17053 - page 4

    100 Mbps, Full−duplex 100 Mbps, Full−duplex 100 Mbps, Half−duplex Duplex Mismatch 1 AUTO 100 Mbps, Full−duplex 100 Mbps, Half−duplex 100 Mbps, Full−duplex Duplex Mismatch 1 100 Mbps, Full−duplex 100 Mbps, Full−duplex 100 Mbps, Full−duplex 100 Mbps, Full−duplex Correct Manual Configuration 2 100 Mbps, Half−duplex AUTO 100 Mbps, ...

  • Cisco Systems 17053 - page 5

    2 Some third−party NIC cards can fall back to half−duplex operation mode, even though both the switchport and NIC configuration are manually configured for 100 Mbps, full−duplex. This is because NIC autonegotiation link detection still operates when the NIC is manually configured. This causes duplex inconsistency between the switchport and th ...

  • Cisco Systems 17053 - page 6

    Example for Cisco IOS Software on the Switch − Catalyst 2900XL, 3500XL, 2948G−L3, and 6000 that Run Cisco IOS Software show interfaces type Switch# show interfaces fastethernet 0/1 FastEthernet0/1 is down, line protocol is down • States other than connected and line protocol is up indicate a physical connectivity issue. Complete these steps i ...

  • Cisco Systems 17053 - page 7

    This is an example: %PAGP−5−PORTFROMSTP:Port 3/3 left bridge port 3/3 %PAGP−5−PORTTOSTP:Port 3/3 joined bridge port 3/3 For Cisco IOS Software−based switches, these messages appear for link up/down situations: %LINK−3−UPDOWN: Interface interface , changed state to up %LINK−3−UPDOWN: Interface interface , changed state to down This ...

  • Cisco Systems 17053 - page 8

    collisions are normal. Generally, a one percent ratio of errors to total traffic is acceptable for half−duplex connections. If the ratio of errors to input packets is greater than two or three percent, performance degradation can be noticed. In half−duplex environments, it is possible for both the switch and the connected device to sense the wi ...

  • Cisco Systems 17053 - page 9

    64−byte transmit time occurs. They are only detected during transmissions of packets longer than 64 bytes. Its detection is exactly the same as it is for a normal collision; it just happens later than it does for a normal collision. Excessive Collisions Excessive collisions are the number of frames that are dropped after 16 attempts to send the p ...

  • Cisco Systems 17053 - page 10

    Multiple Collisions This is an indication of a half−duplex configuration. Late Collisions This is an indication of faulty hardware (NIC, cable, or switch port) or a duplex mismatch. Excessive Collisions This is an indication of overutilization of the switch port at half−duplex or duplex mismatch. Carrier Sense This is an indication of faulty ha ...

  • Cisco Systems 17053 - page 11

    2 In−Discard and Lrn−Discard do not exist on all Catalyst platforms. Table 5Possible Causes for Incrementing CatOS Counters Counter Possible Cause Delay Exced Severe problem with the switch. Create a service request with Cisco Technical Support. MTU−Exced Verify ISL and dot1q configurations. Verify another switch or router does not inject ...

  • Cisco Systems 17053 - page 12

    Teaming of Network Interface Cards Teaming of Network Interface Cards, or NIC Teaming, can cause instability in the networks. Such setups can introduce disruptions to the Spanning tree and can make it undergo frequent recomputations. If intermittent loss of connectivity to NIC teamed servers occurs for devices or hosts in the same VLAN, try to disa ...

  • Cisco Systems 17053 - page 13

    Cisco Catalyst Switch Compatibility and Operation−Specific Issues These sections deal with specific Cisco Catalyst switch issues that can affect performance, compatibility, and interoperation of certain NICs. Catalyst 8510 and 8540 CSR In the campus switch router (CSR) Cisco IOS Software Release 12.0(5)W5(13), autonegotiation for speed and duplex ...

  • Cisco Systems 17053 - page 14

    after an autonegotiation failure. For detailed information on Cisco bug IDs, refer to the Bug Toolkit ( registered customers only ) . Refer to Cisco Catalyst 6500 Series Switches Release Notes for more Catalyst 6000 and 6500 documented bug fixes. Catalyst 5000 and 5500 Switches This table lists several known issues found on the Catalyst 5000 and 55 ...

  • Cisco Systems 17053 - page 15

    WS−X5225R) can result in speed or duplex mismatches under certain conditions. The problem typically occurs after the module is reset or the switch port is disabled and reenabled. The workaround is to disconnect and reconnect the cable that connects the workstation to the switch port. CSCdk32984 ( registered customers only ) 4.2(2) The 48−port, ...

  • Cisco Systems 17053 - page 16

    day to once a month. This issue can reoccur even after the switch is power cycled. The purpose of this Cisco bug ID is to combine several software reworks, fixes that resolve and reduce the loss of connectivity issues, and additional troubleshooting checks in software. CSCdr37645 ( registered customers only ) 4.5(8), 5.5(2), 6.1(1) An invalid packe ...

  • Cisco Systems 17053 - page 17

    CSCds89148 ( registered customers only ) 5.5.6, 6.2.1 Xmit−Err counter increments on unconnected ports for unexplained reasons. The bug also resolves an issue of high−CPU utilization conditions that can be caused by unconnected ports that are configured as host ports. For detailed information on Cisco bug IDs, refer to the Bug Toolkit ( registe ...

  • Cisco Systems 17053 - page 18

    For detailed information on Cisco bug IDs, refer to the Bug Toolkit ( registered customers only ) . NIC Compatibility and Operation Issues Disclaimer : Use this table as a guide in order to troubleshoot NIC issues. Consult the NIC vendor for verification and proper resolution of the issue. Table 11 NIC Model/Manufacture Symptom Description Resoluti ...

  • Cisco Systems 17053 - page 19

    AsantéFast 10/100 PCI Adapter Slow login or fails to log in to server.  See technical document TID1084 at Asanté support website. AsantéFast 10/100 PCI Adapter Numerous CRC and FCS errors reported on switch when connected to Power Macintosh 9500.  See technical document TID1109 at Asanté support website. AsantéFast 10/100 PCI Adapter Slo ...

  • Cisco Systems 17053 - page 20

    traffic. 3Com 3C905/3C905B Intermittent DHCP issues. Despite the proper configuration of Catalyst switch ports, workstations still experience some intermittent DHCP issues. Upgrade to driver version 4.01b or later, which resolves DHCP issues. 3Com 3C905/3C905B Unable to log in to Novell Internetwork Packet Exchange (IPX) network. Despite the proper ...

  • Cisco Systems 17053 - page 21

    1.0.33921641.2241835. 3Com 3C985/3C985B Novell 5.0 issues Refer to 3Com technical support reference 1.0.16744826.2027011. 3Com 3C985/3C985B Clients are unable to log in or browse server, but pings work correctly.  Refer to 3Com technical support reference 2.0.4428387.2305072. 3Com 3C985/3C985B Packets larger than Ethernet MTU (1518 bytes) are ge ...

  • Cisco Systems 17053 - page 22

    fails. The motherboards were manufactured with an Intel Chipset that are incompatible with Cisco switches and Netgear hubs. IBM 10/100 EtherJet CardBus Adapter Extremely slow performance when operating at 10 Mbps. Certain 10/100 switches implement automatic correction for polarity−reversed cables that are not completely compatible with the same c ...

  • Cisco Systems 17053 - page 23

    can see poor network connections or excessive numbers of dropped packets. The interoperability issue arises when a module with a ten bit interface (TBI) transmits an odd byte packet to a receiver with a Gigabit media−independent interface (GMII). Carrier Extension is detailed in subsection 35.2.3.5 in the IEEE 802.3 specification. Carrier Extensi ...

  • Cisco Systems 17053 - page 24

    type keyword can be set to Auto Detect or 10BASE−T/100BaseTX. The related port on the attached hub or switch must also be set to 10Mbps, full−duplex. Xircom RealPort2 CardBus Ethernet 10/100 Adapter (R2BE/RBE/CBE) Models Extremely slow performance when operating at 10 Mbps. Certain 10/100 switches implement automatic correction for polarity−r ...

  • Cisco Systems 17053 - page 25

    manufacturer patches and utility software are installed. Xircom XE2000 PCMCIA NIC Does not autonegotiate to 100 Mbps, full−duplex. NIC only autonegotiates to 100 Mbps, half−duplex. Known limitation of XE2000 NIC. Refer to the XE2000 release notes. Appendix A: Information to Gather Before Creating a Service Request If the troubleshooting procedu ...

  • Cisco Systems 17053 - page 26

    0.14 Loopback 1 = loopback mode switched on 0 = loopback mode switched off 0.13 Rate Selection (least−significant bit [LSB]) 0.6 0.13 1 1 reserved 1 0 1000 Mbps 0 1 100 Mbps 0 0 10 Mbps 0.12 Autonegotiation Enable 1 = autonegotiaton enabled 0 = autonegotiation disabled 0.11 Power Down 1 = power down 0 = normal down 0.10 Isolated 1 = PHY electrica ...

  • Cisco Systems 17053 - page 27

    partner and defaults to half−duplex. As described in Appendix B: Understanding How Autonegotiation Works, pulses within the FLP are used to derive code words that exchange link partner capabilities. The first code word exchanged is referred to as the base page. It informs each link partner of the message type, IEEE 802.3 or IEEE 802.9a, and a tec ...

Manufacturer Cisco Systems Category Switch

Documents that we receive from a manufacturer of a Cisco Systems 17053 can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- 17053 manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems 17053
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems 17053.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems 17053, service manual, brief instructions and user manuals Cisco Systems 17053. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems 17053.

Similar manuals

A complete manual for the device Cisco Systems 17053, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems 17053 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems 17053.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems 17053 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems 17053, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems 17053, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems 17053 - which should help us in our first steps of using Cisco Systems 17053
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems 17053
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems 17053 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems 17053?

Use the form below

If you did not solve your problem by using a manual Cisco Systems 17053, ask a question using the form below. If a user had a similar problem with Cisco Systems 17053 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)