Manual ADTRAN Total Access 544R

162 pages 1.78 mb
Download

Go to site of 162

Summary
  • ADTRAN Total Access 544R - page 1

    61200704L2- 1B July 2003 T OT AL ACCESS 544R System Manual 4200704L2#A TM T otal Access 544R A TM 1200704L3 T otal Access 544R without Power Cord 4200704L8 T otal Access 544R wi th Euro Power Cord 4200704L9 T ot al Access 544R T ot al Access 5 44R with UK Power Cord 4200704L10 T ot al Access 544R with Australian Pow er Cord 4200704L1 1 T otal Acces ...

  • ADTRAN Total Access 544R - page 2

    Trademarks Total Access 544R System Manual 2 © 2003 ADTRAN, Inc. 61200704L2-1B T rademarks Any brand names an d product names included in th is manual are trademarks, registered trademarks, or trade names of their respective holders. T o the Holder of the Manual The content s of this manu al are current as of the da te of publication. ADTRAN reser ...

  • ADTRAN Total Access 544R - page 3

    Total Access 544R System Manual Revision History 61200704L2-1B © 2003 ADTRAN, Inc. 3 Revision History This is the second issue of this manual. Conventions Notes pr ovide additiona l useful information. Cautions signify information that could pr event service interruption. W arnings pr ovide information that could pr event damage to the equipment o ...

  • ADTRAN Total Access 544R - page 4

    Safety Instructions Total Access 544R System Manual 4 © 2003 ADTRAN, Inc. 61200704L2-1B Safety Instructions When using your teleph one equipment, please follow these basic safety precautions to reduce the risk of fire, electrical shock, or personal injury: 1. Do not use this prod uct near water , such as a bathtub, wash bo wl, kitchen sink, laundr ...

  • ADTRAN Total Access 544R - page 5

    Total Access 544R System Manual Save These Important Safety Instructions 61200704L2-1B © 2003 ADTRAN, Inc. 5 Federal Communications Co mmission Radio Frequency Inte rference S t atement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to ...

  • ADTRAN Total Access 544R - page 6

    Affidavit Requir ements for Connection to Digital Servic es Total Access 544R System Manual 6 © 2003 ADTRAN, Inc. 61200704L2-1B Affidavit Requirements for C onnection to Di git al Services • An affidavit is required to be given to the telephone company whene ver digita l terminal equipment without encoded analog content and billing protection is ...

  • ADTRAN Total Access 544R - page 7

    Total Access 544R System Manual Affidavit Re quirem ents for Connection to Digital Services 61200704L2-1B © 2003 ADTRAN, Inc. 7 Affidavit for Connect ion of Customer Premises Equipment to 1.544 Mbp s and/or Subrate Digit al Services For the work to be performed in the certified terri tory of _____________ ______ (telco name) S tate of ________ ___ ...

  • ADTRAN Total Access 544R - page 8

    Affidavit Requir ements for Connection to Digital Servic es Total Access 544R System Manual 8 © 2003 ADTRAN, Inc. 61200704L2-1B This ________ da y of __________ _____, _______ __________ ___________ ____________ Notary Public My commission expires: __________ ___________ ____________ ...

  • ADTRAN Total Access 544R - page 9

    Total Access 544R System Manual In dustry Canada Compliance Information 61200704L2-1B © 2003 ADTRAN, Inc. 9 Industry Canada Compliance Information Notice: The Industry Cana da label ap plied to the product (identified by the Industry Canada logo or the “IC:” in front of the certificatio n/registration numb er) signifies that the In dustry Cana ...

  • ADTRAN Total Access 544R - page 10

    Product Warranty Total Access 544R System Manual 10 © 2003 ADTRAN, Inc. 61200704L2-1B Product W arranty ADTRAN will replace or repair this product within th e warranty period if it does not meet its published specifications or fails while in service. W arranty in formation ca n be found at www .adtran.com/warranty . Product Registration Registerin ...

  • ADTRAN Total Access 544R - page 11

    Total Access 544R System Manual Customer Serv ice, Product Support In formation, and Trainin g 61200704L2-1B © 2003 ADTRAN, Inc. 11 Post-Sale Support Y our reseller should serve as the firs t point of con tact for support. If ad ditional support is n eeded, the ADTRAN Support web site provide s a variety of support services su ch as a searchable k ...

  • ADTRAN Total Access 544R - page 12

    Customer Service, Product Support Informa tion, and Training Total Access 544R System Manual 12 © 2003 ADTRAN, Inc. 61200704L2-1B ...

  • ADTRAN Total Access 544R - page 13

    61200704L2-1B © 2003 ADTRAN, Inc. 13 T able of Content s Section 1 System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 This section of ADTRAN’s Product System Man ual is designed for use by netw ork engineers, planners, and designers for overvi ew informat ion about the Product. It contains gener ...

  • ADTRAN Total Access 544R - page 14

    Table of Contents Total Access 544R System Manual 14 © 2003 ADTRAN, Inc. 61200704L2-1B ...

  • ADTRAN Total Access 544R - page 15

    61200704L2-1B © 2003 ADTRAN, Inc. 15 SYSTEM DESCRIPTION This section of ADTRAN’s Pr oduct System Manual is designed for use by network engineers, planners, and designers for overview in formation about the Produ ct. It contains general information and describes the L2 protocol support, routing capability , security , and testing features. This s ...

  • ADTRAN Total Access 544R - page 16

    Section 1 System Descriptio n Total Access 544R Syste m Manual 16 © 2003 ADTRAN, Inc. 61200704L2-1B 1. SYSTEM OVERVIEW The T otal Access 544R is a cost-effective SHDSL access router designed for small and medium businesses, branch offices and campuses. The unit provides up to 2312 kbps for dedicated Internet access or remote office connectivity . ...

  • ADTRAN Total Access 544R - page 17

    Total Access 544R Sys tem Manual Section 1 System Description 61200704L2-1B © 2003 ADTRAN, Inc. 17 • ICMP Ping utility • Trace route utility Sof t ware Upgradeable • TFTP download • XMODEM via CRAFT port Network Interface G .shdsl: (ITU G .991.2 Compliant ) • Line Rate: 200- 2312 kbps (3 -36 DS0s) • Physical Interface: RJ-48C • Rate ...

  • ADTRAN Total Access 544R - page 18

    Section 1 System Descriptio n Total Access 544R Syste m Manual 18 © 2003 ADTRAN, Inc. 61200704L2-1B A TM Support •6 P V C s • IP over ATM (RFC 1483 ) • RFC 1483 (Multiprotocol Encapsul ation over ATM), PPPoA (RFC 2364) • Full Traffic Shaping and QoS Support • VBR-rt and UBR Support • F5 OAM Loopback Capability PPP • LCP, IPCP, BCP, C ...

  • ADTRAN Total Access 544R - page 19

    61200704L2-1B © 2003 ADTRAN, Inc. 19 ENGINEERING GUIDELINES Provides equipment dimensions, po wer re quirements, fr ont panel design , rear pa nel design, LEDs, and at-a-glance specifications. C ONTENT S Reviewing the Front Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Front Panel ...

  • ADTRAN Total Access 544R - page 20

    Section 2 Engine ering Guidelines Total Access 544R System Manual 20 © 2003 ADTRAN, Inc. 61200704L2-1B 1. POWER REQUIREMENT S The T otal A ccess 544R operates with 240 V AC, 50 Hz and a maximum current drain of 300 mA. The T otal Access 544R maximum power consumption shall not excee d 10 W atts. 2. REVIEWIN G THE FR ONT PANEL DESIGN Figure 1. show ...

  • ADTRAN Total Access 544R - page 21

    Total Access 544R System Manual Section 2 Engineering Gu idelines 61200704L2-1B © 2003 ADTRAN, Inc. 21 3. REVIEWIN G THE RE AR PANEL DESIGN The T otal Access 544R rear panel is shown in Figure 2.. Figure 2. Total Access 544R Rear Panel NTWK Connection (RJ-48C) The NTWK connection pinout is an SHDS L connection. T able 1 shows the pin out for this ...

  • ADTRAN Total Access 544R - page 22

    Section 2 Engine ering Guidelines Total Access 544R System Manual 22 © 2003 ADTRAN, Inc. 61200704L2-1B 10/100BASET Connection (RJ-48C) The 1 0/100BASET port (RJ-48C) provides a 10/100BaseT Ethe rnet LAN connection, which is used for IP Routing , TFTP , SNMP , and T elnet connec tions. T a ble 4 shows the 10/100BASET port pinout. AC Power Connectio ...

  • ADTRAN Total Access 544R - page 23

    Total Access 544R System Manual Section 2 Engineering Gu idelines 61200704L2-1B © 2003 ADTRAN, Inc. 23 4. DB-9 TO RJ ADAPTER The DB-9 to RJ adapter is use d to connect a PC or VT100 terminal to the CRAFT port. The adapter pinout is shown in T able 5. Table 5. DB-9 to RJ Adapter Pinout DB-9 RJ-45 DESCRIPTION 25 TX Data 33 RX Data 51 GND Note: All o ...

  • ADTRAN Total Access 544R - page 24

    Section 2 Engine ering Guidelines Total Access 544R System Manual 24 © 2003 ADTRAN, Inc. 61200704L2-1B ...

  • ADTRAN Total Access 544R - page 25

    61200704L2-1B © 2003 ADTRAN, Inc. 25 NETWORK T URNUP PROCEDURE Provides shipment content s list, grounding instruct ions, mounting options, an d specifics of supplying power to the unit. C ONTENT S Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Unp ...

  • ADTRAN Total Access 544R - page 26

    Section 3 Ne twork Turnup Pr ocedure Total Access 544R System Manual 26 © 2003 ADTRAN, Inc. 61200704L2-1B 1. INTRODUCTION This section discusses the unit installation process. 2. T OOLS REQU IRED The tools required for unit installation are: • Screws (customer-provided for wallmount installation) • Screwdriver (for wall or rackmount installati ...

  • ADTRAN Total Access 544R - page 27

    Total Access 544R System Manual Section 3 Networ k Turnup Procedur e 61200704L2-1B © 2003 ADTRAN, Inc. 27 • 4 Screws (P/N 3276003 003) • RJ-45 to DB-9 Adapter (P /N 3196ADPT001) • The Total Access 544R base unit 4. GROUNDING INSTRUCTIONS The following provid es grounding instructi on info rmation from the Underwrite rs’ Laboratory UL60950 ...

  • ADTRAN Total Access 544R - page 28

    Section 3 Ne twork Turnup Pr ocedure Total Access 544R System Manual 28 © 2003 ADTRAN, Inc. 61200704L2-1B 5. SUPPLYING POWER TO THE UNIT The AC powered unit comes equippe d with a detachable power cord with a 3-prong plug for co nnecting to a grounded power receptacle. As ship ped, the unit is set to factory de fault conditions. After installing t ...

  • ADTRAN Total Access 544R - page 29

    61200704L2-1B © 2003 ADTRAN, Inc. 29 SHDSL RCU A TM USER INTERFACE GUIDE The SHDSL RCU A TM User Interface Guide is designed for use by network administr ators and others who will configure and provision the system . This section provides details unique to the SHDSL RCU A TM firmware. It cont ains an overview , applicati on det ails, configuration ...

  • ADTRAN Total Access 544R - page 30

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 30 © 2003 ADTRAN, Inc. 61200704L2-1B 1. SYSTEM INFO The System Info menu provides b asic information about the unit as we ll as data fields for editing information. Figure 1 displays th e submenus th at are available when you select this menu item. Figure 1. System Info ...

  • ADTRAN Total Access 544R - page 31

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 31 S YSTEM I NF O > U NIT N AME Product-specific name for the unit. S YSTEM I NF O > CLEI C ODE The CLEI code for the unit. S YSTEM I NF O > P ART N UMB ER ADTRAN part number for the unit. S YSTEM I NF O > S ERIAL N UMBER Th ...

  • ADTRAN Total Access 544R - page 32

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 32 © 2003 ADTRAN, Inc. 61200704L2-1B S YSTEM C ONFIG Set up the unit’ s operational configuration from the S YSTE M C ONFIG menu. Figure 3 shows the ite ms included in this menu. Figure 2. System Config Menu S YSTEM C ONFIG > M ANAGEMENT Set up the CRAFT P ORT , T E ...

  • ADTRAN Total Access 544R - page 33

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 33 S YSTEM C ONFIG > M ANAGEMENT > C RAFT P ORT > I DLE T IME This option defines the amount of time in minutes user may stay connected without any activity on the CRAFT port before the user is automatically logged out of the s ...

  • ADTRAN Total Access 544R - page 34

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 34 © 2003 ADTRAN, Inc. 61200704L2-1B S YSTEM C ONFIG > M ANAGEMENT > T EL NET A CCES S > A CCES S Sets A CCESS to O N or O FF . The factory default value for this parameter is O N . S YSTEM C ONFIG > M ANAGEMENT > T EL NET A CCES S > A UTHEN M ETHOD Set ...

  • ADTRAN Total Access 544R - page 35

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 35 S YSTEM C ONFIG > M ANAGEMENT > T EL NET A CCES S > IP A CCESS L IST Set up the list of allowed telnet managers. Table 2. Telnet Security Levels Security Level Descripti on Full The us er has all ac cess to view and config u ...

  • ADTRAN Total Access 544R - page 36

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 36 © 2003 ADTRAN, Inc. 61200704L2-1B S YSTEM C ONFIG > M ANAGEMENT > SNMP M ANAG EMENT Access the SNMP management an d configure the SNMP communiti es and traps from this menu. S YSTEM C ONFIG > M ANAGEMENT > SNMP M ANAG EMENT > A CCESS When set to O FF , ...

  • ADTRAN Total Access 544R - page 37

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 37 S YSTEM C ONFIG > M ANAGEMENT > SNMP M ANAG EMENT > T RAP S Sets up the trap manager name and IP from this menu. S YSTEM C ONFIG > M ANAGEMENT > FDL M ANAG EMENT Enables the FDL management and configures mode and IP ad ...

  • ADTRAN Total Access 544R - page 38

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 38 © 2003 ADTRAN, Inc. 61200704L2-1B S YSTEM C ONFIG > M ANAGEMENT > FDL M ANAG EMENT > F AR -E ND IP A DDRESS This is the far-end IP address used for the FDL ma nagement. The FDL is a separate IP network from the customer data that is configured under the Route ...

  • ADTRAN Total Access 544R - page 39

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 39 S YSTEM C ONFIG > S YSLOG > S YSLOG F ACILITY The choices are: L OCAL 0 , L OCAL 1 , L OCAL 2 , L OCAL 3 , L OCAL 4 , L OCAL 5 , L OCAL 6 , L OCAL 7 . S YSLOG F ACILITY is the facility level for all messages forwarded from the ...

  • ADTRAN Total Access 544R - page 40

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 40 © 2003 ADTRAN, Inc. 61200704L2-1B SYSLOG using T erminal Mode Another option for configuring sy slog is using the terminal mode com mand log dump <logna me> . The logname must be all CAPS and b e one of the follo wing names: FA TA L ALER T CRITICAL ERROR WA R N ...

  • ADTRAN Total Access 544R - page 41

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 41 S YSTEM C ONFIG > S YSLOG > PPP L EVEL Minimum required level for sending P PP log messages. S YSTEM C ONFIG > S YSLOG > NA T L EVEL Minimum required level for sending NA T log messages. S YSTEM C ONFIG > S YSLOG > ...

  • ADTRAN Total Access 544R - page 42

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 42 © 2003 ADTRAN, Inc. 61200704L2-1B S YSTEM C ONFIG > S YSLOG > NOKIA L EVEL Minimum required level for sending lo g messages about communication w ith the Nokia DSLAM. Messages are only generated for prod ucts with an SHDSL W AN interface. S YSTEM C ONFIG > S ...

  • ADTRAN Total Access 544R - page 43

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 43 S YSTEM C ONFIG > S YSLOG > VOICE L EVEL Minimum required level for sending lo g messages about AAL2 voices services. Messages are only generated for A TM products. S YSTEM C ONFIG > S YSLOG > JETSTREAM L EVEL Minimum req ...

  • ADTRAN Total Access 544R - page 44

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 44 © 2003 ADTRAN, Inc. 61200704L2-1B S YSTEM C ONFIG > S YSLOG > BRIDGE L EVEL Minimum required level for sending b ridge mode log messages. S YSTEM C ONFIG > S YSLOG > MAINT L EVEL Minimum required level for se nding CRAFT port log messages. S YSTEM C ONFIG ...

  • ADTRAN Total Access 544R - page 45

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 45 S YSTEM C ONFIG > N ETWORK T IME > T IME Z ONE All time zones are based off of Greenwich Me an T ime (GMT). The choices are listed below •G M T • GMT -5 (E AS TERN ) • GMT -6 (C ENTRAL ) • GMT -7 (M OUNT AIN ) • GMT - ...

  • ADTRAN Total Access 544R - page 46

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 46 © 2003 ADTRAN, Inc. 61200704L2-1B S YSTEM U TILITY Use the S YSTEM U TILI TY menu to view and set the system parameters shown in Figure 4. Figure 3. Syst em Utility Menu S YSTEM U TILITY > U PGRADE F IRMWARE Select the firmware upgrade method and perform upgrade fr ...

  • ADTRAN Total Access 544R - page 47

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 47 S YSTEM U TILITY > U PGRADE F IRMWARE > TFTP S ERVER F ILENAME This is required when the transfer method is TFTP . It is the case-sens itive file name which contains the upgrade code. The factory defa ult is no entry in the TFT ...

  • ADTRAN Total Access 544R - page 48

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 48 © 2003 ADTRAN, Inc. 61200704L2-1B S YSTEM U TILITY > C ONFIG T RANS FER > TFTP S ERVER IP A DDRESS Specifies the IP address of the TFTP server . Get this number from your system administrator . If using the ADTRAN Utilities TFTP server , this number appears in t ...

  • ADTRAN Total Access 544R - page 49

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 49 S YSTEM U TILITY > S YS TEM U TILIZATION > P ERFOR MANCE > T OTAL A VG CPU U TILIZAT ION T OTAL A VG CPU U TILIZATION is a running total of CPU u tilization since the last reset. S YSTEM U TILITY > S YSTEM U TILIZATION &g ...

  • ADTRAN Total Access 544R - page 50

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 50 © 2003 ADTRAN, Inc. 61200704L2-1B S YSTEM U TILITY > P ING > # T RANSMI T S T otal packets sent (read only). S YSTEM U TILITY > P ING > # R ECEIVES T otal packets received (read only). S YSTEM U TILITY > P ING > % L OSS Percentage loss based on pin g ...

  • ADTRAN Total Access 544R - page 51

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 51 S YSTEM U TILITY > T ERMINAL M ODE Selecting the terminal mode gives the user a command-line prompt to perform utilities such as pings, traceroutes, resets, firmware updates, configuration, and more. T ERMINAL M ODE can also be ac ...

  • ADTRAN Total Access 544R - page 52

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 52 © 2003 ADTRAN, Inc. 61200704L2-1B noNat Do not NA T the tra ce packets Options may be entered in any order and may be truncated. V alid interface names are eth0, fdl0, ppp0, fr0, fr1, etc. Example u sage: trace 10.0.0.5 h 20 t 1 r 1 so eth0 This will perform a trace t ...

  • ADTRAN Total Access 544R - page 53

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 53 I NTERFACES (SHDSL) V iew the SHDSL interface status and conf igure SHDSL paramete rs from this menu. Figure 4. Interfaces Menu I NTERFACES (SHDSL) > C ONFIG > A NNEX = A/B Select the maintenance or signaling protocol used ov e ...

  • ADTRAN Total Access 544R - page 54

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 54 © 2003 ADTRAN, Inc. 61200704L2-1B I NTERFACES (SHDSL) > S TA T US > SHDSL S TATS > F RAME M ODE Displays the type of framing (either SHDSL Fr amed or SHDSL Framed Plesio w/bit stuf fing). I NTERFACES (SHDSL) > S TA T US > SHDSL S TATS > G . HS E VENT ...

  • ADTRAN Total Access 544R - page 55

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 55 I NTERFACES (SHDSL) > S TA T US > EOC S TATS > V ENDOR S ERIAL N UMBER Serial number of remote unit. I NTERFACES (SHDSL) > S TA T US > EOC S TATS > V ENDOR S OFTWARE V ERSION Software version of remote unit. I NTERF ...

  • ADTRAN Total Access 544R - page 56

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 56 © 2003 ADTRAN, Inc. 61200704L2-1B I NTERFACES > S TA T U S > MAC A DD RESS This is a read-only field which displays the unique MAC address programmed at ADTRAN. I NTERFACES > S TA T U S > D ATA L INK Displays the data link layer protocol status. L2 P ROTOC ...

  • ADTRAN Total Access 544R - page 57

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 57 L2 P ROTOCOL (SHDSL) > P ROT OCOL > A T M Asynchronous T ransfer Mode allocates bandwidth on demand, automatically adjusting the network capacity to meet the system needs. Fixed-le ngth cells (53 octet) require lower processing ...

  • ADTRAN Total Access 544R - page 58

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 58 © 2003 ADTRAN, Inc. 61200704L2-1B L2 P ROTOCOL (SHDSL - A TM) > C ONFIG > PVC C ONFIG > A CT IVE Activates the A TM PVC. The choices are Y ES or N O . Default is N O . L2 P ROTOCOL (SHDSL - A TM) > C ONFIG > PVC C ONFIG > S UB -I NTERFACE The SHDSL S ...

  • ADTRAN Total Access 544R - page 59

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 59 N ONE The connection will not allow th e PPP peer to authenticate it. P AP , C HAP , OR E AP The unit will ask for EAP during the first PPP LCP negotiation and allow the PPP peer to negotiate down to CHAP or PA P . C HAP OR E AP The ...

  • ADTRAN Total Access 544R - page 60

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 60 © 2003 ADTRAN, Inc. 61200704L2-1B L2 P ROTOCOL (SHDSL - A TM) > C ONFI G > P VC C ONFIG > C ONNECTION [R OUTER ] > S ETUP > M ODE This mode identifies how the data w ill be transferred. The choices are: The default is R OUTE IP . L2 P ROTOCOL (SHDSL - A ...

  • ADTRAN Total Access 544R - page 61

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 61 AP: R X C ELLS This is the number of cells received. AP: R X OAM C ELLS This is the number of OAM cells received AP: R ECEIVE C ELLS D ISCARDED This is the number of cells received and discarded. An incrementing count in this field c ...

  • ADTRAN Total Access 544R - page 62

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 62 © 2003 ADTRAN, Inc. 61200704L2-1B AAL5: N O AT M F RAMES This is for internal use only . AAL5: N O D ATA P ACKET S This is for internal use only . C LEAR S TA TS This is used to clear the co unters on this menu screen. L2 P ROTOCOL (SHDSL - A TM) > S TA T U S > ...

  • ADTRAN Total Access 544R - page 63

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 63 L2 P ROTOCOL (SHDSL - A TM) > S TA T U S > PVC S TA T U S > P ROTOCO L S TAT US Use these menus to view the P ROTOCOL S TATS and to C LEAR S TATS for the PVC Protocol. L2 P ROTOCOL (ETH) Configure the L2 PROTOCOL parameters ...

  • ADTRAN Total Access 544R - page 64

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 64 © 2003 ADTRAN, Inc. 61200704L2-1B L2 P ROTOCOL (ETH) > I NTER FACE Displays the in terface type. L2 P ROTOCOL (ETH) > P ROTOCOL Displays the L2 protocol for the 10 /1 00BaseT Ethernet port. Currently only 802.3 is supported. L2 P ROTOCOL (ETH) > C ONFIG Confi ...

  • ADTRAN Total Access 544R - page 65

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 65 L2 P ROTOCOL (ETH) > S TAT U S > E XCESSIVE C OLLIS IONS T otal number of collisions that resulted in packet being drop ped. L2 P ROTOCOL (ETH) > S TAT U S > D EFERRE D T RANSMISS IONS T otal number of packets de ferred d ...

  • ADTRAN Total Access 544R - page 66

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 66 © 2003 ADTRAN, Inc. 61200704L2-1B Figure 6. Bridge Menu B RIDGE > C ONFIG Configure the interfaces and bridge table parameters from this menu. B RIDGE > C ONFIG > I NTERFACES Configure the SHDSL interface brid ging parameters from this menu. B RIDGE > C ON ...

  • ADTRAN Total Access 544R - page 67

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 67 B RIDGE > C ONFIG > B RIDGE T ABLE > B RIDGE T ABLE A GING (0-65535) B RIDGE T ABLE A GING is how soon an entry ages out of the Br idge table (in minutes). Default is 5. B RIDGE > S TA T US V iew the bridging statistics f ...

  • ADTRAN Total Access 544R - page 68

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 68 © 2003 ADTRAN, Inc. 61200704L2-1B Figure 7. Router Menu R OUTER > C ONFIG Configure the interfaces, routes, DHCP Serv er , and UDP Relay options from this menu. R OUTER > C ONFIG > I NTERFACES Configure the layer 3 options for the Ethe rnet and SHDSL interfac ...

  • ADTRAN Total Access 544R - page 69

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 69 R OUTER > C ONFIG > I NTERFACES (ETH)> S ETUP Configure the Ethernet addressing, RIP , and Proxy ARP from this menu. P RIMARY IP This is used to setup the IP addresses for the LAN on the unit. IP A DDRESS The IP address assi ...

  • ADTRAN Total Access 544R - page 70

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 70 © 2003 ADTRAN, Inc. 61200704L2-1B R OUTER > C ONFIG > I NTERFACES (ETH) > S UB -I NTERFACE The Ethernet sub-interface is A TM[0. 1]. The [0.1] represents the A TM physica l and logical ports, when 0 is the physical port and 1 is t he logical port as signed to ...

  • ADTRAN Total Access 544R - page 71

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 71 R OUTER > C ONFIG > R OUTES Configures the default gateway an d static routes from this menu. R OUTER > C ONFIG > R OUTES > D EFAULT G ATEWAY The default gateway is used by the unit to send IP packets whose destination ...

  • ADTRAN Total Access 544R - page 72

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 72 © 2003 ADTRAN, Inc. 61200704L2-1B R OUTER > C ONFIG > DHCP S ERVER > DHCP M ODE When set to O N , the unit acts as a DHCP server and will dy namically assign IP , network mask, default gateway , and DNS addresses to any device which transmits a broadcast DHCP ...

  • ADTRAN Total Access 544R - page 73

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 73 R OUTER > C ONFIG > UDP R ELAY > UDP R ELAY L IST Up to four relay destination servers can be specified in this list. R OUTER > S TA TU S Vi e w t h e IP R OUTES , IP S TATS , and ARP C ACHE statistics from this menu. R O ...

  • ADTRAN Total Access 544R - page 74

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 74 © 2003 ADTRAN, Inc. 61200704L2-1B R OUTER > S TA TU S > IP R OU TES > U SE Number of times the unit has referenced the route. R OUTER > S TA TU S > IP R OU TES > F LAGS Important tags associated with this route entry R OUTER > S TA TU S > IP R ...

  • ADTRAN Total Access 544R - page 75

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 75 R OUTER > S TA TU S > IP S TA TS This section describes the following Statistics submen us (and see the tables on the pages following): •I P •I C M P •T C P • UDP All of these statistics are taken from the MIB-II variab ...

  • ADTRAN Total Access 544R - page 76

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 76 © 2003 ADTRAN, Inc. 61200704L2-1B B AD PROTOC OL DISCARDS The number of locally-addressed datagrams rece ived successfully but discarded because of an unknown or unsupp orted protocol. D AT AGRAMS DISCARDED The number of input IP datagrams fo r which no problems were ...

  • ADTRAN Total Access 544R - page 77

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 77 R OUTER > S TA TU S > IP S TA TS > ICMP IP REASSEMBLY FAILURES The number of failures detected by the IP reasse mbly algorithm (for whatever reason: timed out, errors, etc.). Note that this is not necessarily a co unt of dis ...

  • ADTRAN Total Access 544R - page 78

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 78 © 2003 ADTRAN, Inc. 61200704L2-1B ICMP T IMEOUT S R ECEIVED The number of ICMP T ime Exceeded mess ages received. ICMP P ARAMETER P ROBLEM M SGS R CVD The number of ICMP Parameter Problem messages received. ICMP SOURCE QUENCH MSGS RCVD The number of ICMP Source Quench ...

  • ADTRAN Total Access 544R - page 79

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 79 ICMP P ACKET E RRORS this unit did not send due to proble ms discovered within ICMP such as a lack of buffers. This value should not include errors discovere d outside the ICMP layer such as the inability of IP to rout e the resultan ...

  • ADTRAN Total Access 544R - page 80

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 80 © 2003 ADTRAN, Inc. 61200704L2-1B R OUTER > S TA TU S > IP S TA TS > UDP V iew the UDP statistics from this menu. R OUTER > S TA TU S > IP S TA TS > UDP T ABLE V iew the UDP table statistics from this menu. ICMP A DDR M ASK R EPLY M SGS S ENT The num ...

  • ADTRAN Total Access 544R - page 81

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 81 R OUTER > S TA TU S > IP S TA TS > TCP V iew the TCP statistics from this menu. R ETRANSMISSION T IMEOUT A LGORITHM The algorithm used to de termine the timeout value used for retransmitting unackn owledged octets. M IN R ET ...

  • ADTRAN Total Access 544R - page 82

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 82 © 2003 ADTRAN, Inc. 61200704L2-1B R OUTER > S TA TU S > IP S TA TS > TCP C ONNS V iew the TCP Conns S t atistics from this menu. This table shows the different states of each TCP connection. TCP C URRENT C ONNECTIONS The number of TCP connections for which th ...

  • ADTRAN Total Access 544R - page 83

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 83 R OUTER > S TA TU S > IP S TA TS > ARP C ACHE This lists the contents of the units’ s ARP table. A ll resolved cache entries tim e out after 20 minutes. Unresolved entries time out in 3 minutes. The ARP cache can be cleare ...

  • ADTRAN Total Access 544R - page 84

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 84 © 2003 ADTRAN, Inc. 61200704L2-1B S ECURITY > F IL TERS Configure the filter characteristics from this menu. S ECURITY > F IL TERS > F ILTER D EFINES The unit can filter packets based on certain parameters within the pack et. The method used by the unit allow ...

  • ADTRAN Total Access 544R - page 85

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 85 S ECURITY > F IL TERS > F ILTER D EFINES > P ATTERN F ILTER D EFINES The pattern filter is applied to bridge packets only . Th at is any packet which is forward ed by the bridge functionality of the unit. Up to 32 pattern de ...

  • ADTRAN Total Access 544R - page 86

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 86 © 2003 ADTRAN, Inc. 61200704L2-1B S RC A DDR IP address compared to the source address. V a lue is in dotted decimal format. Default is 0.0.0.0 . S RC M ASK Bits which are used in the source comparison. V alue is in dotted deci mal format. Default is 0. 0.0.0 . D EST ...

  • ADTRAN Total Access 544R - page 87

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 87 S ECURITY > R AD IUS S ERVER The parameters for the Radius Serv er are configured in this menu. S ECURITY > R AD IUS S ERVER > S ERVER 1 This is the IP address of the first RADIUS S ERVER that the unit should attemp t to com ...

  • ADTRAN Total Access 544R - page 88

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 88 © 2003 ADTRAN, Inc. 61200704L2-1B S ECURITY > R AD IUS S ERVER > S ERVER 2 This is the IP address of the second RADIUS S ERVER that the unit should attempt to communicate with when the primary server does not respond. Defa ult is 0 .0.0. 0. S ECURITY > R AD I ...

  • ADTRAN Total Access 544R - page 89

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 89 S ECURITY > R AD IUS S ERVER > UDP P ORT This is the UDP port the unit shoul d use when communicating with the RADIUS S ERVER . The default is 1812 , which is the commonly used port. S ECURITY > R AD IUS S ERVER > S ECRET ...

  • ADTRAN Total Access 544R - page 90

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 90 © 2003 ADTRAN, Inc. 61200704L2-1B Appendix A. RFC1483 Qu ick St art (IP Routing) The T otal Access 544R allow s for complete integration of data delivery from on e compact platform (see Figure 9). Multiple users can share ne twork access over a single SHDSL connection ...

  • ADTRAN Total Access 544R - page 91

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 91 . IP Routing Ste p A ct i on 1. From the T otal Access 544R main menu, select the L2 P ROTOCOL > I NTERFACES menu. Set up the A TM network here . 2. Select the AT M C ONFIG menu located under the main C ONFIG field. 3. Enter the I ...

  • ADTRAN Total Access 544R - page 92

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 92 © 2003 ADTRAN, Inc. 61200704L2-1B Appendix B. RFC1483 Quick St art (IP Routing with NA T) T o illustrate the use of NA T , consider the example from Appendix B. T o set up a si ngle public address that will be used to access th e public network, you will use the NA T ...

  • ADTRAN Total Access 544R - page 93

    Total Access 544R System Manual Sect ion 4 SHDSL RCU ATM User Interfac e Guide 61200704L2-1B © 2003 ADTRAN, Inc. 93 Appendix C. RFC 1483 Qu ick S t art (Bridging) The T otal Access 544R allow s for complete integr ation of data delivery from one compact platform. T o configure a T otal Access 544R for Bridging, yo u need to know the VPI values for ...

  • ADTRAN Total Access 544R - page 94

    Section 4 SHDSL RCU ATM User Interface Guide T otal Access 544R System Manual 94 © 2003 ADTRAN, Inc. 61200704L2-1B ...

  • ADTRAN Total Access 544R - page 95

    61200704L2-1B © 2003 ADTRAN, Inc. 95 DET AIL LEVEL PROCEDURES DLP-1 Connecting the Termina l or PC to the CRAFT Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 DLP-2 Logging in to the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 DLP-3 Adding/Removing Teln e ...

  • ADTRAN Total Access 544R - page 96

    Section 5 Detail Level Procedures Total Access 544R System Manual 96 © 2003 ADTRAN, Inc. 61200704L2-1B ...

  • ADTRAN Total Access 544R - page 97

    61200704L2-1B © 2003 ADTRAN, Inc. 97 DLP-1 Connecting the T erminal or PC to the CRAFT Port Introduction Provisioning is facilitated by a series of intuitive menus that ar e accessible on a co mputer screen. Connecting either a VT100 terminal or a PC emulating a VT100 terminal to the CRAFT po rt on the rear of the unit allows access to the menus a ...

  • ADTRAN Total Access 544R - page 98

    Section 5 DLP-1 Total Access 544R System Manual 98 © 2003 ADTRAN, Inc. 61200704L2-1B 1. Connect a VT100 terminal to the unit. 2. Connect a PC emulating a VT 100 terminal to the unit. 3. Most personal computers or laptops can run communications so ftware that will emulate a VT100 terminal. Windows pr ograms suc h as T ermin al © or Hype rtermina l ...

  • ADTRAN Total Access 544R - page 99

    Total Access 544R System Manual Section 5 DLP-1 61200704L2-1B © 2003 ADTRAN, Inc. 99 Follow-up Procedures Once this procedure is complete, return to the proced ure which referred you to th is DLP and continue with the tasks indicated there. ...

  • ADTRAN Total Access 544R - page 100

    Section 5 DLP-1 Total Access 544R System Manual 100 © 2003 ADTRAN, Inc. 61200704L2-1B ...

  • ADTRAN Total Access 544R - page 101

    61200704L2-1B © 2003 ADTRAN, Inc. 101 DLP-2 Logging in to the System Introduction Once connected to the unit via either a VT100 terminal or PC configured as a VT100 terminal, it is necessary to log in to the system to gain access to the management and provisio ning functions. This DLP provides specific steps for logging in to the system and access ...

  • ADTRAN Total Access 544R - page 102

    Section 5 DLP-2 Total Access 544R System Manual 102 © 2003 ADTRAN, Inc. 61200704L2-1B 1. After connecting to the system , a blank screen will appear . Pressing any key will display the login screen shown below . The cursor will blink at the L OGIN field, waiting for a password to be entered. 2. At the L OGIN field, enter the p assword for the unit ...

  • ADTRAN Total Access 544R - page 103

    Total Access 544R System Manual Section 5 DLP-2 61200704L2-1B © 2003 ADTRAN, Inc. 103 3. Upon entering the corre ct password, the M AIN M ENU is displayed as shown below . Y ou are now logged in to the menu system. Follow-up Procedures Once this procedure is complete, return to the proced ure which referred you to th is DLP and continue with the t ...

  • ADTRAN Total Access 544R - page 104

    Section 5 DLP-2 Total Access 544R System Manual 104 © 2003 ADTRAN, Inc. 61200704L2-1B ...

  • ADTRAN Total Access 544R - page 105

    61200704L2-1B © 2003 ADTRAN, Inc. 105 DLP-3 Adding/Removing T elnet Users and Changing Password Security Levels Introduction All menu items in the unit are protected by passwords of varying security leve ls. By assigning different passwords to different security levels, the System Administrator can control which users can view or change various me ...

  • ADTRAN Total Access 544R - page 106

    Section 5 DLP-3 Total Access 544R Manual 106 © 2003 ADTRAN, Inc. 61200704L2-1B 1. Connect to the unit usin g either th e 10/100B ASE T or CRAFT interfac es. If you are not already connected to the unit’ s CRAFT interface (either with a VT100 compatible terminal or with a PC runn ing VT100 emulation software), follow the procedure in DLP-1, Conne ...

  • ADTRAN Total Access 544R - page 107

    Total Access 544R Manual Section 5 DLP-3 61200704L2-1B © 2003 ADTRAN, Inc. 107 The unit contains six dif ferent password levels. The table below gives a brief de scription of each level. Follow-up Procedures Once this procedure is complete, return to the proced ure which referred you to th is DLP and continue with the tasks indicated there. Securi ...

  • ADTRAN Total Access 544R - page 108

    Section 5 DLP-3 Total Access 544R Manual 108 © 2003 ADTRAN, Inc. 61200704L2-1B ...

  • ADTRAN Total Access 544R - page 109

    61200704L2-1B © 2003 ADTRAN, Inc. 109 DLP-4 Setting Ethernet IP Parameters Introduction If the unit is connected to an IP network for T elnet , TFTP , or SNMP management, several IP parameters must be set for the unit to commun icate with the network. These para meters are described in this DLP along with the procedures for setting them. Prerequis ...

  • ADTRAN Total Access 544R - page 110

    Section 5 DLP-4 Total Access 544R System Manual 110 © 2003 ADTRAN, Inc. 61200704L2-1B 1. Connect the unit to your VT1 00 system (details fo und in DLP-1, Co nnecting the T erminal or PC to the CRAFT Port ). 2. Log in to the system with maximum right s (details for logging in are in DLP-2 and DLP-3). 3. From the R OUTER /C ONFIG /I NTERFACES (E TH ...

  • ADTRAN Total Access 544R - page 111

    61200704L2-1B © 2003 ADTRAN, Inc. 111 DLP-5 V erifying Communica tions Over an IP LAN Introduction When an ETHERNET port is connected to a local area network (L AN), test steps must be performed on the unit to ensure that it is communic ating properly over the network. This procedure outlines those steps. Prerequisite Procedures Before beginning t ...

  • ADTRAN Total Access 544R - page 112

    Section 5 DLP-5 Total Access 544R System Manual 112 © 2003 ADTRAN, Inc. 61200704L2-1B 1. Ascertain the unit IP address. If you do not already have the IP Address for the unit, obtain it from the Network Administrator or manually check for the address in the R OUTER /C ONFIG /I NTERFACES (E TH )/S ETUP /P RIMARY IP/IP A DDRESS menu. 2. Ping the uni ...

  • ADTRAN Total Access 544R - page 113

    Total Access 544R System Manual Section 5 DLP-5 61200704L2-1B © 2003 ADTRAN, Inc. 113 3. T elnet to th e unit. From the same computer used in the previous step, T elnet to the unit and verify that the T elnet session is properly opened (see DLP-6, T elnettin g to the Unit ). Once the T elnet session is established, press <Ctrl + L> to log ou ...

  • ADTRAN Total Access 544R - page 114

    Section 5 DLP-5 Total Access 544R System Manual 114 © 2003 ADTRAN, Inc. 61200704L2-1B ...

  • ADTRAN Total Access 544R - page 115

    61200704L2-1B © 2003 ADTRAN, Inc. 115 DLP-6 T elnetting to the Unit Introduction If the T otal Access 544R is part of a mana gement cluster connected to the local ne twork, you may use a PC connected to the network to T elnet into the unit. This procedure details the steps wh ich mu st be performed to T elnet into the unit. Prerequisite Procedures ...

  • ADTRAN Total Access 544R - page 116

    Section 5 DLP-6 Total Access 544R System Manual 116 © 2003 ADTRAN, Inc. 61200704L2-1B 1. Connect the co mputer to the unit’ s CRAFT port as shown in DLP-1, Connecting the T erminal or PC to the CRAFT Port . 2. Log in to the unit as shown in DLP-2, Logging in to the System . 3. Select S YSTEM C ONFIG , M ANAGEMENT , and T ELNET A CCESS . 4. Right ...

  • ADTRAN Total Access 544R - page 117

    Total Access 544R System Manual Section 5 DLP-6 61200704L2-1B © 2003 ADTRAN, Inc. 117 12. From a remote computer system co n nected to the LAN, T elnet to the unit. The following screen will appear . 13. Enter the user name assigne d in S tep 7 and press <Enter> . The following screen will appear . 14. Enter the passwo rd assigned in S tep 7 ...

  • ADTRAN Total Access 544R - page 118

    Section 5 DLP-6 Total Access 544R System Manual 118 © 2003 ADTRAN, Inc. 61200704L2-1B Y ou are now T elnetted into the unit’ s menu system. 15. When you complete your configuration changes and save the changes (when prompted), press <Ctrl+L> to log out and close the session. Follow-up Procedures Once this procedure is complete, return to t ...

  • ADTRAN Total Access 544R - page 119

    61200704L2-1B © 2003 ADTRAN, Inc. 119 DLP-7 Upgrading the Firmware Using XMODEM Introduction The unit supports firmware updates via the 10/1 00B ASE T port using either TFTP from a network server or the CRAF T interface using XMODEM. XMODEM is found in the VT100 terminal application in the ADTRAN Utilities package and in most PC VT100 co mmunicati ...

  • ADTRAN Total Access 544R - page 120

    Section 5 DLP-7 Total Access 544R System Manual 120 © 2003 ADTRAN, Inc. 61200704L2-1B 1. Connect to the unit usin g the CRAFT interfac e. If you are not already connected to the unit’ s CRAFT interface (either with a VT100 compatible terminal or with a PC running VT100 emulation so ftware), follow the procedure in DLP-1, Connecting the T erminal ...

  • ADTRAN Total Access 544R - page 121

    61200704L2-1B © 2003 ADTRAN, Inc. 121 DLP-8 Upgrading the Firmware Using TFTP Introduction The unit supports firm ware updates via the 10/100B ASE T Ethernet port using either TFTP from a network server or the CRAFT interfaces using XMODEM. The unit also supports TFTP updates across the W AN using the data/router channe ls. This DLP provides the s ...

  • ADTRAN Total Access 544R - page 122

    Section 5 DLP-8 Total Access 544R System Manual 122 © 2003 ADTRAN, Inc. 61200704L2-1B For LAN Upgrades 1. Connect to the unit us ing the 10/100B ASE T interface. If you are not already connected to the unit’ s 10/100B ASE T port using T elnet client software, use the procedure in DLP-6, T elnetting to the Unit , to connect to the unit. 2. V erif ...

  • ADTRAN Total Access 544R - page 123

    Total Access 544R Sys tem Manual Section 5 DLP-8 61200704L2-1B © 2003 ADTRAN, Inc. 123 Prior to the start of the upgrade, the transfer status will display I DLE . During the TFTP upload, various status messages display in T RANSFER S TAT U S to indicate progress. The following table describes these messages. 9. When the update h as su ccessfully c ...

  • ADTRAN Total Access 544R - page 124

    Section 5 DLP-8 Total Access 544R System Manual 124 © 2003 ADTRAN, Inc. 61200704L2-1B Prior to the start of the upgrade, the transfer status will display I DLE . During the TFTP upload, various status messages display in T RANSFER S TAT U S to indicate progress. The following table describes these messages. 8. When the upd ate has su ccessfully co ...

  • ADTRAN Total Access 544R - page 125

    61200704L2-1B © 2003 ADTRAN, Inc. 125 DLP-9 Saving the Current Configuration Using TFTP Introduction The unit supports configuration transfers from the unit (via the 10/100B ASE T Ethernet port) to a TFTP server located on the network or a TFTP server accessible across the W AN. This DLP provides the steps to follow for a successful configuration ...

  • ADTRAN Total Access 544R - page 126

    Section 5 DLP-9 Total Access 544R System Manual 126 © 2003 ADTRAN, Inc. 61200704L2-1B Saving Configuration using T FTP Server on Local Network 1. Connect to the unit usin g the 10/1 00B ASE T interfac e. If you are not already connected to the unit’ s 10/100B ASE T port using T elnet client software, use the procedure in DLP-6, T elnetting to th ...

  • ADTRAN Total Access 544R - page 127

    Total Access 544R Sys tem Manual Section 5 DLP-9 61200704L2-1B © 2003 ADTRAN, Inc. 127 Saving Configuration using TFTP Server Accessible Across the W AN 1. T elnet into the unit us ing F ULL or S UPPORT levels (refer to DLP-3, Adding/Removing T elnet Users and Changing Passw ord Security Levels ). 2. V erify the TFTP server is r unning on the netw ...

  • ADTRAN Total Access 544R - page 128

    Section 5 DLP-9 Total Access 544R System Manual 128 © 2003 ADTRAN, Inc. 61200704L2-1B ...

  • ADTRAN Total Access 544R - page 129

    61200704L2-1B © 2003 ADTRAN, Inc. 129 DLP-10 Loading the Current Conf iguration Using TFTP Introduction The unit supports configuration uploads from a uni t (via the 10/100B ASE T Ethernet port) to a TFTP server located on the network or a TFTP server accessible across the W AN. This DLP provides the steps for a successful configuration upload usi ...

  • ADTRAN Total Access 544R - page 130

    Section 5 DLP-10 Total A ccess 544R System Manual 130 © 2003 ADTRAN, Inc. 61200704L2-1B Loading Configuration using T FTP Server on Local Network 1. Connect to the unit usin g the 10/1 00B ASE T interfac e. If you are not already connected to the unit’ s 10/100B ASE T port using T elnet client software, use the procedure in DLP-6, T elnetting to ...

  • ADTRAN Total Access 544R - page 131

    Total Access 544R System Manual Section 5 DLP-10 61200704L2-1B © 2003 ADTRAN, Inc. 131 Loading Configuration using TFTP Server Accessible Across the W AN 1. T elnet into the unit us ing F ULL or S UPPORT levels (refer to DLP-3, Adding/Removing T elnet Users and Changing Passw ord Security Levels ). 2. V erify the TFTP server is r unning on the net ...

  • ADTRAN Total Access 544R - page 132

    Section 5 DLP-10 Total A ccess 544R System Manual 132 © 2003 ADTRAN, Inc. 61200704L2-1B the tasks indicated there. ...

  • ADTRAN Total Access 544R - page 133

    61200704L2-1B © 2003 ADTRAN, Inc. 133 DLP-1 1 Saving the Current Configuration Using XMODEM Introduction The unit supports configuratio n tran sfers from the unit using a VT100 term inal or terminal emulator (with XMODEM) and the CRAFT interface. This DLP provides the steps to follow for a successful configuration transfer using the CRAFT port and ...

  • ADTRAN Total Access 544R - page 134

    Section 5 DLP-11 Total A ccess 544R System Manual 134 © 2003 ADTRAN, Inc. 61200704L2-1B Perform Steps Below in the Order Listed 1. Connect to the unit using the RJ-45 CRAFT interface. If you are not already connected to the unit’ s CRAFT interface (either with a VT100 compatible terminal or with a PC running VT100 emulation software), follo w th ...

  • ADTRAN Total Access 544R - page 135

    61200704L2-1B © 2003 ADTRAN, Inc. 135 DLP-12 Loading the Current Conf iguration Using XMODEM Introduction The unit supports configuration uplo ads from a unit using a VT 100 terminal or terminal emulator (with XMODEM) and the CRAF T interface. This DLP provid es the steps for a successful configuration upload using the CRAFT port and XMODEM. Prere ...

  • ADTRAN Total Access 544R - page 136

    Section 5 DLP-12 Total A ccess 544R System Manual 136 © 2003 ADTRAN, Inc. 61200704L2-1B 1. Connect to the unit using the RJ-45 CRAF T inte rface. If you are not already connected to the unit’ s CRAF T interface (either with a VT100 compatible terminal or with a PC runn ing VT100 emulation software), follow the procedure in DLP-1, Connecting the ...

  • ADTRAN Total Access 544R - page 137

    61200704L2-1B © 2003 ADTRAN, Inc. 137 DLP-13 Saving and Loading T ext Co nfiguration Using the T erminal Command Line Introduction The unit has the ability to dow nload a text file which contains the co nfiguration of the entire unit. This configuration may be altered in a text editor and then uploaded to the unit . This DLP will explain how to sa ...

  • ADTRAN Total Access 544R - page 138

    Section 5 DLP-13 Total A ccess 544R System Manual 138 © 2003 ADTRAN, Inc. 61200704L2-1B Saving the Router's Configuration 1. Establish a connec tion to the router with t he terminal software either thr ough the C RAFT por t or via a T elnet session. 2. From the M ain Menu, select S YSTEM U TI LITY , then T ERMINAL M ODE , and then press <E ...

  • ADTRAN Total Access 544R - page 139

    Total Access 544R System Manual Section 5 DLP-13 61200704L2-1B © 2003 ADTRAN, Inc. 139 7. Press the SP ACE BAR to continue. The router will then prin t its configuration to the terminal screen. (With capture en abled, the term inal software will capture the configurat ion and write it to the file that you designated.) 8. When the configura tion st ...

  • ADTRAN Total Access 544R - page 140

    Section 5 DLP-13 Total A ccess 544R System Manual 140 © 2003 ADTRAN, Inc. 61200704L2-1B ...

  • ADTRAN Total Access 544R - page 141

    61200704L2-1B © 2003 ADTRAN, Inc. 141 DLP-14 Unit Inst allation Us ing T he Auto-Config Feature Introduction A UTO -C ONFIG allows the service provider to gain initial acces s to a newly installed IAD while in its factory default state. This eliminates the need for a skilled technician on-site duri ng installation, as it only requires someone to m ...

  • ADTRAN Total Access 544R - page 142

    Section 5 DLP-14 Total A ccess 544R System Manual 142 © 2003 ADTRAN, Inc. 61200704L2-1B T o prevent electrical shock, do not inst all equipment in a we t lo cation or duri ng a lightning storm. ...

  • ADTRAN Total Access 544R - page 143

    Total Access 544R System Manual Section 5 DLP-14 61200704L2-1B © 2003 ADTRAN, Inc. 143 1. V erify the un it is at fact ory default. 2. Connect the network inte rface cable to the NTWK port on the rear of th e unit. 3. Power up the unit. 4. The unit begins auto -detecting whether the packet s receiv ed on the W AN in terface are PPP LCP packets or ...

  • ADTRAN Total Access 544R - page 144

    Section 5 DLP-14 Total A ccess 544R System Manual 144 © 2003 ADTRAN, Inc. 61200704L2-1B 8. T ype Save at the > prompt. This a pplies all configurat ion changes and the cu rrent connection is lost. 9. At this point, the service pr ovider reconfig ures the network to match the unit's new configuration. 10. After the networ k configuration is ...

  • ADTRAN Total Access 544R - page 145

    61200704L2-1B © 2003 ADTRAN, Inc. 145 DLP-15 A.03 to A.04 Firmware Upgrade Introduction Until now , the T ota l Access 544R ha s been running firmware version A. 03.xx. Recently , A.04.xx has been released. The development of A.04.xx code is a sign ificant step in the evolution of the T otal Access product line, as it allows all T o tal Access fam ...

  • ADTRAN Total Access 544R - page 146

    Section 5 DLP-15 Total A ccess 544R System Manual 146 © 2003 ADTRAN, Inc. 61200704L2-1B Prerequisite Procedures Obtain the A.04 firmware and the A.03.9X (T ransition Build) firmware from the ADTRAN website (http://www .ADTRAN.com). T ools and Materials Required • VT100 comp atible terminal or comp ut er with terminal emulation software • Appro ...

  • ADTRAN Total Access 544R - page 147

    Total Access 544R System Manual Section 5 DLP-15 61200704L2-1B © 2003 ADTRAN, Inc. 147 Upgrade From A.03 to A.03.9 X (T ransition Build) to A.04 1. Upgrade the fir mware from A. 03 to A.03.9 X (T r ansition Build ) firmware. S ee DLP-7 or DL P-8 for instructions on how to perfor m this upgrade. 2. Once the upgrade to A.03.9X is complete, immediate ...

  • ADTRAN Total Access 544R - page 148

    Section 5 DLP-15 Total A ccess 544R System Manual 148 © 2003 ADTRAN, Inc. 61200704L2-1B ...

  • ADTRAN Total Access 544R - page 149

    61200704L2-1B © 2003 ADTRAN, Inc. 149 ADTRAN UTILITIES Provides instructions for configuring and using the ADTRAN Utilities so ftware programs including T e lnet, VT100, Syslog, and TFTP . ADTRAN delivers several PC software utilities alon g with the T otal Access 544R. These utilities are located on the CD-ROM that came with your shipment. They a ...

  • ADTRAN Total Access 544R - page 150

    Section 6 ADTRAN Utilities Tot al Access 544R System Manual 150 © 2003 ADTRAN, Inc. 61200704L2-1B 1. T ELNET UTILITY The T elnet utility delivered with the T otal Access 544R provides enhancements to standard T elnet programs that make it easier to wo rk with T otal Access 544R options. Access the T e lnet program remotely through the 10BaseT Ethe ...

  • ADTRAN Total Access 544R - page 151

    Total Access 544R System Manu al Section 6 ADTRAN Utilities 61200704L2-1B © 2003 ADTRAN, Inc. 151 Host Name Accepts and stores host names. Y ou may either enter a name, an IP address, or a domain name directly from this field. Click on the dro p-down arrow to di splay a complete list of previously stored host names. P ORT Provides several port opt ...

  • ADTRAN Total Access 544R - page 152

    Section 6 ADTRAN Utilities Tot al Access 544R System Manual 152 © 2003 ADTRAN, Inc. 61200704L2-1B Edit Menu Provides C OPY and P ASTE commands . Options Menu Provides viewing alternativ es for the terminal screen. Colors Three options change the color o f the background window ( B ACK G ROUND ), bold highlights ( B OLD ), and text ( T EXT ). Local ...

  • ADTRAN Total Access 544R - page 153

    Total Access 544R System Manu al Section 6 ADTRAN Utilities 61200704L2-1B © 2003 ADTRAN, Inc. 153 About Displays version and owner information. 2. VT100 UTILITY Use the VT100 to configure an T otal Access 544R whic h is directly connected to a PC. The VT100 display is almost identical to the T elnet display . For a detailed description of how to w ...

  • ADTRAN Total Access 544R - page 154

    Section 6 ADTRAN Utilities Tot al Access 544R System Manual 154 © 2003 ADTRAN, Inc. 61200704L2-1B Disconnect Closes a specified serial port at the end of a VT100 session. File T ransfer Uploads and downloads files to and from an T otal Access 544R. XMODEM CRC Selects the XMODEM file transfer protocol. ASCII Cfg Files Selects ASCII transfer mode. P ...

  • ADTRAN Total Access 544R - page 155

    Total Access 544R System Manu al Section 6 ADTRAN Utilities 61200704L2-1B © 2003 ADTRAN, Inc. 155 Content s Opens on-line help. About Displays version and owner information. 3. TFTP SERVER The TFTP Server utility transfers T o tal Access 544R configuration file s to and from a TFTP server (see Figure 3 for the menu tree). Y o u can install this pr ...

  • ADTRAN Total Access 544R - page 156

    Section 6 ADTRAN Utilities Tot al Access 544R System Manual 156 © 2003 ADTRAN, Inc. 61200704L2-1B Figure 4. TFTP Server Interface Only one configuration transfer session (upload or download) may be active at a time. The TCP/IP parameters are not saved or overwritten as part of an T o tal Access 544R unit’ s tr ansf erred conf iguration to allow ...

  • ADTRAN Total Access 544R - page 157

    Total Access 544R System Manu al Section 6 ADTRAN Utilities 61200704L2-1B © 2003 ADTRAN, Inc. 157 Content s Opens on-line help. About Displays version and owner information. 4. STATUS FIELD This field displays general informatio n about port and transfer status. This field is read-only . The unlabeled field in the center of th e screen displays pr ...

  • ADTRAN Total Access 544R - page 158

    Section 6 ADTRAN Utilities Tot al Access 544R System Manual 158 © 2003 ADTRAN, Inc. 61200704L2-1B ...

  • ADTRAN Total Access 544R - page 159

    61200704L2-1B © 2003 ADTRAN, Inc. 159 MIBS Provides a listing of SNMP Management Info rmation Ba ses (MIBs) supported by the T otal Access 544R. T raps supported fo r each MIB are also listed. C ONTENT S MIBs Supported by the Total Access 544R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 MIB Compilation Or ...

  • ADTRAN Total Access 544R - page 160

    Section 7 MIBs Total Access 544R System Manual 160 © 2003 ADTRAN, Inc. 61200704L2-1B 1. MIBS SUPPORTED BY THE T OTAL ACCESS 544R St andard RFC MIBs : RFC1573.mi2 IANAifT ype-MIB RFC1907.mi2 SNMPv2-MIB RFC201 1.mi2 IP-MIB RFC2096.mi2 IP-FORW ARD-MIB RFC21 15.mi2 FRAME-RELA Y -DTE-MIB RFC2493.mi2 PerfHist-TC-MIB RFC2494.mi2 DS0-MIB and DS0BUNDLE-MIB ...

  • ADTRAN Total Access 544R - page 161

    Total Access 544R System Manual Section 7 MIBs 61200704L2-1B © 2003 ADTRAN, Inc. 161 2. MIB COMPILATION ORDER 3. T RAP S SUPPORT ED BY THE T OTAL ACCESS 544R IANAifT ype-MIB PerfHist-TC-MIB SNMPv2-MIB (if not included with SNMP manager) IF-MIB IP-MIB IP-FORW AR D-MIB FRAME-RELA Y -DTE-MIB DS1-MIB DS0-MIB DS0BUNDLE-MIB EtherLike-MIB CIRCUIT -IF-MIB ...

  • ADTRAN Total Access 544R - page 162

    Section 7 MIBs Total Access 544R System Manual 162 © 2003 ADTRAN, Inc. 61200704L2-1B 4. MIB V ARIABLES SUPPORTED BY THE T OTAL ACCESS 544R SNMPv2 states the su pported MIB variables by the follo wing method: The unit will have a MIB called T A 6XX.mi2 that w ill describe the SNMP variab les supported. This MIB will contain an AGENT -CAP ABILITIES ...

Manufacturer ADTRAN Category Router

Documents that we receive from a manufacturer of a ADTRAN Total Access 544R can be divided into several groups. They are, among others:
- ADTRAN technical drawings
- Total Access 544R manuals
- ADTRAN product data sheets
- information booklets
- or energy labels ADTRAN Total Access 544R
All of them are important, but the most important information from the point of view of use of the device are in the user manual ADTRAN Total Access 544R.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals ADTRAN Total Access 544R, service manual, brief instructions and user manuals ADTRAN Total Access 544R. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product ADTRAN Total Access 544R.

A complete manual for the device ADTRAN Total Access 544R, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use ADTRAN Total Access 544R by users. Manuals are usually written by a technical writer, but in a language understandable to all users of ADTRAN Total Access 544R.

A complete ADTRAN manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual ADTRAN Total Access 544R - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the ADTRAN Total Access 544R, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the ADTRAN Total Access 544R, that we can find in the current document
3. Tips how to use the basic functions of the device ADTRAN Total Access 544R - which should help us in our first steps of using ADTRAN Total Access 544R
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with ADTRAN Total Access 544R
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of ADTRAN Total Access 544R in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning ADTRAN Total Access 544R?

Use the form below

If you did not solve your problem by using a manual ADTRAN Total Access 544R, ask a question using the form below. If a user had a similar problem with ADTRAN Total Access 544R it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)