English dropdown-ico

Manual Porter-Cable FN250A

13 pages 1.17 mb
Download

Go to site of 13

Summary
  • Porter-Cable FN250A - page 1

    Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...

  • Porter-Cable FN250A - page 2

    2 PORTER ✦ ✦ CABLE Porter-Cable Corporation 4825 Highway 45 North Jackson, TN 38305 Date of Manufacture: ___________________________ Fecha de fabricación:, Date de fabrication: Serial No: ______________________________________ Número de serie:, Nombre d'ordre GB ENGLISH EC-DECLARA TION OF CONFORMITY We declare under our sole responsibili ...

  • Porter-Cable FN250A - page 3

    3 indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. used without the safety al ...

  • Porter-Cable FN250A - page 4

    4 1. Read and understand tool labels and manual. Failure to follow warnings could result in DEATH or SERIOUS INJURY . Fig. 1. 2 . Operator and others in work area MUST wear safety glasses with side shields. These safety glasses must conform to ANSI Z87.1 requirements (approved glasses have “Z87” printed or stamped on them). Fig. 2. 3. Keep fing ...

  • Porter-Cable FN250A - page 5

    5 Fig. 8 Fig. 9 Fig. 10 Fig. 7 Fig. 11 Fig. 12 Fig. 13 9. Do not connect tool to pressure which potentially exceeds 200 PSI (13.7 BAR). 10 . Only use air hose that is rated for a maximum working pressure of at least 150 PSI (10.3 BAR) or 150% of the maximum system pressure, which ever is greater. 11. Connect tool to air supply hose with a coupling ...

  • Porter-Cable FN250A - page 6

    6 21. Remove finger from trigger when not driving fasteners. Never carry tool with finger on trigger. In “Contact Actuation Mode” tool will fire a fastener if safety is bumped while trigger is depressed. Fig. 14. 22. Do not overreach. Keep proper footing and balance at all times when using or handling the tool. 23. Fire fasteners into work surf ...

  • Porter-Cable FN250A - page 7

    7 Employer must enforce compliance with the safety warnings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and understand tool labels and manual. Failure to follow warnings could result in DEATH or SERIOUS IN ...

  • Porter-Cable FN250A - page 8

    8 Never point tool at yourself or others. Always connect tool to air supply before loading fasteners (Fig. 18). Do not load fasteners with trigger or safety depressed. Only use approved Porter-Cable fasteners. Operator and others in work area MUST wear safety glasses with side shields. Always wear ANSI Z87.1 approved safety glasses, and ANSI S3.19 ...

  • Porter-Cable FN250A - page 9

    9 F ASTENER GUIDE A Fastener Guide (A) Fig. 23 and 24, is factory installed on Model FN250A. The Guide is held in place with a bolt and nut (B) Fig. 23 and 24. The Fastener Guide must be used whenever driving fasteners that are less than 1 1 / 2 " long. The Fastener Guide must be removed when driving fasteners that are 1 1 / 2 " or more i ...

  • Porter-Cable FN250A - page 10

    10 Remove finger from trigger when not driving fasteners. Never carry tool with finger on trigger: tool will fire a fastener if safety is bumped. Keep fingers AWAY from trigger when not driving fasteners to avoid accidental firing. Never carry tool with finger on trigger. In “Contact Actuation Mode” t ool will fire a fastener if safety is bumpe ...

  • Porter-Cable FN250A - page 11

    11 CLEAN AND INSPECT DAIL Y Disconnect tool from air supply before cleaning and inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammable cleaning solutions to wipe exterior of tool only if necessary. DO NOT SOAK tool with cleaning solutions. Such solutions can damage int ...

  • Porter-Cable FN250A - page 12

    12 2. Tool does nothing or Inadequate air supply. Verify adequate air supply. operates sluggishly. Inadequate lubrication. Put 5 or 6 drops of oil into air inlet. Worn or damaged Install Overhaul Kit. o-rings or seals. 3. Air leak near bottom Loose screws. Tighten screws. of tool. Worn or damaged Install Overhaul Kit. o-rings or bumper. 4. Tool jam ...

  • Porter-Cable FN250A - page 13

    The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...

Manufacturer Porter-Cable Category Nail Gun

Documents that we receive from a manufacturer of a Porter-Cable FN250A can be divided into several groups. They are, among others:
- Porter-Cable technical drawings
- FN250A manuals
- Porter-Cable product data sheets
- information booklets
- or energy labels Porter-Cable FN250A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Porter-Cable FN250A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Porter-Cable FN250A, service manual, brief instructions and user manuals Porter-Cable FN250A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Porter-Cable FN250A.

Similar manuals

A complete manual for the device Porter-Cable FN250A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Porter-Cable FN250A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Porter-Cable FN250A.

A complete Porter-Cable manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Porter-Cable FN250A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Porter-Cable FN250A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Porter-Cable FN250A, that we can find in the current document
3. Tips how to use the basic functions of the device Porter-Cable FN250A - which should help us in our first steps of using Porter-Cable FN250A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Porter-Cable FN250A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Porter-Cable FN250A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Porter-Cable FN250A?

Use the form below

If you did not solve your problem by using a manual Porter-Cable FN250A, ask a question using the form below. If a user had a similar problem with Porter-Cable FN250A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)