English dropdown-ico

Manual Cisco Systems EHWIC1GESFPCU

18 pages 0.26 mb
Download

Go to site of 18

Summary
  • Cisco Systems EHWIC1GESFPCU - page 1

    Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Configuring Gigabit Ethernet Enhanced High-Speed WAN Interface Cards First Published: March 15, 2011 This document describes how to configure the Ci sco Gigabit Ethernet enhanced hi gh-speed W AN interface card (EHWIC). The EHWIC 1 GE-SF P-CU can be insta ...

  • Cisco Systems EHWIC1GESFPCU - page 2

    2 Configuring Gigabit Eth ernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Contents Contents • Prerequisites for the EHWIC 1 GE-SFP-CU • Restrictions for the EHWIC 1 GE-SFP-CU • Overvie w of the EHWIC 1 GE-SFP-CU • Configuring the EHWIC 1 GE-SFP-CU • Confi guring Loopback • Configur ation Examples for EHWIC 1 GE-SFP-CU • Co ...

  • Cisco Systems EHWIC1GESFPCU - page 3

    3 Configuring Gigabit Ethernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Overview of the EHWIC 1 GE-SFP-CU Overview of the EHWIC 1 GE-SFP-CU The Cisco Gigabit Ethernet W AN EHWIC (EHWIC 1 GE -SFP-CU) is an enhanced high-speed interface card provid ing copper and opti cal Gigabit Eth ernet ports and connecti vity of T1/E1 and T3/E3 o ver ...

  • Cisco Systems EHWIC1GESFPCU - page 4

    4 Configuring Gigabit Eth ernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Configuring the EHWIC 1 GE-SFP-CU LEDs Ta b l e 1 lists the LEDs and descri bes their functionali ty a nd dif ferent states. The LEDs provide a vis ual indication of y our av ailable services. Ta b l e 1 L E D I n d i c a t o r s Configuring the EHWIC 1 GE-SFP-CU ...

  • Cisco Systems EHWIC1GESFPCU - page 5

    5 Configuring Gigabit Ethernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Configuring Loopback DETAILED STEPS Configuring Loopback Use the loopback command in in terface conf iguration mode to conf igure loopback. The EHWIC 1 GE-SFP-CU supports MA C layer loopback a nd dri ver type loopback. The MA C loopback is used to detect MA C failu ...

  • Cisco Systems EHWIC1GESFPCU - page 6

    6 Configuring Gigabit Eth ernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Configuration Examples for EHWIC 1 GE-SFP-CU Configuration Examples for EHWIC 1 GE-SFP-CU This section pro vides the follo wing configuration e xamples: • EHWIC 1 GE-SFP-CU Running Configuration, page 6 • Show Controller O utput, page 9 • Show Interface Outp ...

  • Cisco Systems EHWIC1GESFPCU - page 7

    7 Configuring Gigabit Ethernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Configuration Examples for EHWIC 1 GE-SFP-CU ! ! ! redundancy ! ! ! ! ! ! ! interface GigabitEthernet0/0 no ip address duplex auto speed auto ! interface GigabitEthernet0/1 no ip address shutdown duplex auto speed auto ! interface GigabitEthernet0/2 no ip address d ...

  • Cisco Systems EHWIC1GESFPCU - page 8

    8 Configuring Gigabit Eth ernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Configuration Examples for EHWIC 1 GE-SFP-CU ip forward-protocol nd ! no ip http server no ip http secure-server ! ! logging esm config ! ! ! ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 line aux 0 line 67 no activation-character no exec transport preferred ...

  • Cisco Systems EHWIC1GESFPCU - page 9

    9 Configuring Gigabit Ethernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Configuration Examples for EHWIC 1 GE-SFP-CU PID: PVDM2-64 , VID: V01 , SN: FOC1052368L NAME: "SM-ES3-24-P: EtherSwitch SM L3 + PoE + 23 10/100 + 1 10/100/ 1000 on Slot 1", DESCR: "SM-ES3-24-P: EtherSwitch SM L3 + PoE + 23 10/100 + 1 10/100/1000" ...

  • Cisco Systems EHWIC1GESFPCU - page 10

    10 Configuring Gigabit Eth ernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Configuration Examples for EHWIC 1 GE-SFP-CU date_code 08090349 (yymmddvv, v=vendor specific) cc_ext 0xC5 Digital Diag Type 0x00 (Not available) PHY Registers ------------- Register 0x00: 1000 01CD 0362 5D12 0000 0000 0004 2001 Register 0x08: 0000 0000 0000 xxxx ...

  • Cisco Systems EHWIC1GESFPCU - page 11

    11 Configuring Gigabit Ethernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Configuration Examples for EHWIC 1 GE-SFP-CU Fragment Frames Received : 0 In-Range Length Errors : 0 Alignment Errors Received : 0 Symbol Errors Received : 0 Internal MAC Errors : 0 EHWIC-1GE-SFP Mac Tx Statistics: ============================================= Byt ...

  • Cisco Systems EHWIC1GESFPCU - page 12

    12 Configuring Gigabit Eth ernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Configuration Examples for EHWIC 1 GE-SFP-CU Management Interrupt Enable (0x6000): Hwic Int Frame Mgmt Int 0x06 IRQ2 Int 0 IRQ1 Int 0 Graceful Stop Tx Int 0 Network Interrupt Enable (0x3C00): Rx Frame Drop Int 1 Generic Frame Tx Int 1 Generic Frame Rx Int 1 DMA W ...

  • Cisco Systems EHWIC1GESFPCU - page 13

    13 Configuring Gigabit Ethernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Configuring SFPs Hardware is EHWIC-1GE-SFP-CU, address is 000f.f7a2.912b (bia 000f.f7a2.912b) Internet address is 1.1.1.2/24 MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keep ...

  • Cisco Systems EHWIC1GESFPCU - page 14

    14 Configuring Gigabit Eth ernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Configuring Third-Party SFPs • 1000 Mbps speed for 1000B ASE SFPs • Only the follo wing routers and mo dules support third-party SFPs: • Cisco 2921 Integrated Services Router • Cisco 2951 Integrated Services Router • Cisco 3900 Integrated Services Route ...

  • Cisco Systems EHWIC1GESFPCU - page 15

    15 Configuring Gigabit Ethernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Additional References Examples This example sho ws how to conf igure a third- party SFP on a Cisco IS R G2 Series Router: Router# configure terminal Router(config-if)# service unsupported-transceiver Router(config)# interface ethernet 0/3/0 Router(config-if)# medi ...

  • Cisco Systems EHWIC1GESFPCU - page 16

    16 Configuring Gigabit Eth ernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Additional References Standards MIBs RFCs Technical Assistance Cisco and the Cisco logo are tradem arks or registered tr ademarks of Cisco and/or its af filiates in the U.S. and other countries . T o view a list of Cisco trademarks, go to this URL: www .cisco.com ...

  • Cisco Systems EHWIC1GESFPCU - page 17

    17 Configuring Gigabit Ethernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Additional References ©2011- 2013 Ci sco Systems, In c. All right s reserv ed. ...

  • Cisco Systems EHWIC1GESFPCU - page 18

    18 Configuring Gigabit Eth ernet Enhanc ed High-Speed WAN Interface Ca rds OL-24318-02 Additional References ...

Manufacturer Cisco Systems Category Computer Accessories

Documents that we receive from a manufacturer of a Cisco Systems EHWIC1GESFPCU can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- EHWIC1GESFPCU manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems EHWIC1GESFPCU
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems EHWIC1GESFPCU.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems EHWIC1GESFPCU, service manual, brief instructions and user manuals Cisco Systems EHWIC1GESFPCU. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems EHWIC1GESFPCU.

Similar manuals

A complete manual for the device Cisco Systems EHWIC1GESFPCU, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems EHWIC1GESFPCU by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems EHWIC1GESFPCU.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems EHWIC1GESFPCU - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems EHWIC1GESFPCU, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems EHWIC1GESFPCU, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems EHWIC1GESFPCU - which should help us in our first steps of using Cisco Systems EHWIC1GESFPCU
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems EHWIC1GESFPCU
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems EHWIC1GESFPCU in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems EHWIC1GESFPCU?

Use the form below

If you did not solve your problem by using a manual Cisco Systems EHWIC1GESFPCU, ask a question using the form below. If a user had a similar problem with Cisco Systems EHWIC1GESFPCU it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)