Manual Campbell Hausfeld GN0800

20 pages 1.18 mb
Download

Go to site of 20

Summary
  • Campbell Hausfeld GN0800 - page 1

    9. Keep all persons away from parts that move or become hot during operation. 10. Be sure all powered devices are shut off prior to connecting them to the generator. 11. Keep the generator clean and well maintained at all times. Never operate this generator in an explosive atmosphere or poorly ventilated area. ! WARNING Please read and save these i ...

  • Campbell Hausfeld GN0800 - page 2

    A Ground Fault Circuit Interrupter may not be effective if used on a generator that is not grounded! 3. When installing a GFCI, be sure to follow all national and local regulations, or call a licensed or certified electrical technician. GROUNDING 1. Use the ground terminal on the generator frame to connect the unit to a suitable ground source. Secu ...

  • Campbell Hausfeld GN0800 - page 3

    3 GN0950 and GN0800 4. Move the choke/run switch to the choke position. 5. Turn engine switch on by pressing the top of the switch. 6. Pull the starter rope with a brisk smooth motion. 7. Return choke/run switch to the run position. 8. After each start up, allow engine to run 2-3 minutes with no load. Engine speed is preset to provide proper output ...

  • Campbell Hausfeld GN0800 - page 4

    4 Operating Instructions compression cycle, and the intake and exhaust valves are closed. (The piston pushes a small amount of air from the spark plug hole on compression). 6. To clean air filter – Remove filter from generator. Wash in a solvent. Pour motor oil (SAE #20) on filter, squeeze out excess and reinstall in generator. Maintenance (Conti ...

  • Campbell Hausfeld GN0800 - page 5

    5 Zero output from receptacles Low output voltage with no load 6 Vac or above Below 6 Vac High output voltage with no load Low output voltage under load Erratic output voltage Noisy operation Engine won’t start 1. Engine speed is too slow 2. Open or shorted wiring 3. Faulty capacitor 4. Open/shorted rotor or stator windings 5. Open rectifier 1. E ...

  • Campbell Hausfeld GN0800 - page 6

    Operating Instructions 6 Limited W arranty 1. DURATION: Ninety (90) days from the date of purchase by the original purchaser. Units used for rental, industrial or commercial purposes are warranted for 90 days from date of purchase. 2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio ...

  • Campbell Hausfeld GN0800 - page 7

    Favor ler e guardar essas instruções. Leia com atenção antes de tentar montar, instalar, operar ou fazer a manutenção do produto descrito. Proteja a si próprio e a terceiros obedecendo todas as informações de segurança. A não observância dessas instruções pode resultar em lesões pessoais e/ou danos materiais! Guarde essas instruçõe ...

  • Campbell Hausfeld GN0800 - page 8

    8P g Instru çõ es de Opera çã o NUNCA OPERE O GERADOR SOB AS SEGUINTES CONDIÇÕES: 1. Chuva ou mau tempo 2. Vibração excessiva 3. Centelhas 4. Falha do motor 5. Perda de potência elétrica 6. Alteração ou oscilação na velocidade do motor 7. Aquecimento excessivo no equipamento conectado 8. Tomadas danificadas 9. Peças danificadas, queb ...

  • Campbell Hausfeld GN0800 - page 9

    9P g GN0950 and GN0800 2.5 300 600 1000 600 375 250 5 600 1200 500 300 200 125 7.5 900 1800 350 200 125 100 Amps Watts Watts Fio Fio Fio Fio Fio 120 V 220 V No. 8 No.10 No. 12 No. 14 No. 16 EXTENS Õ ES COMPRIMENTOS M Á XIMOS RECOMENDADOS (EM P É S) Opera çã o (continua çã o) 3. Abra a chave de combustível – chave na posição vertical, ap ...

  • Campbell Hausfeld GN0800 - page 10

    10 Pg Instru çõ es de Opera çã o Manuten çã o 3. Coloque aprox. uma colher de chá de óleo no furo da vela. 4. Puxe o cordão de arranque diversas vezes para espalhar o óleo no cilindro. 5. Puxe lentamente o cordão até sentir uma resistência. Isto indica que o pistão está se movendo para cima no ciclo de compressão, e que as válvulas ...

  • Campbell Hausfeld GN0800 - page 11

    11 Pg Saída nula das tomadas Baixa voltagem de saída sem carga 6 Vca ou acima Abaixo de 6 Vca Alta voltagem de saída sem carga Baixa voltagem de saída com carga Voltagem de saída errática Operação ruidosa Motor não dá partida 1. Velocidade do motor muito baixa 2. Fiação aberta ou em curto 3. Capacitor defeituoso 4. Enrolamentos do rotor ...

  • Campbell Hausfeld GN0800 - page 12

    Instru çõ es de Opera çã o 12 Pg Garantia Limitada 1. DURAÇÃO 90 (noventa) dias a partir da data de compra pelo primeiro comprador. Unidades usadas para locação, e finalidades industriais ou comerciais são garantidas por um período de 90 dias da data da compra. 2. QUEM CONCEDE ESTA GARANTIA (GARANTIDOR): Campbell Hausfeld/Scott Fetzer Com ...

  • Campbell Hausfeld GN0800 - page 13

    Notas 13 PG ...

  • Campbell Hausfeld GN0800 - page 14

    ® Sirvase leer y guardar estas instrucciones. Lea con cuidado antes de tratar de armar, instalar, manejar o darle servicio al producto descrito en este manual. Protéjase Ud. y a los demás observando todas las reglas de seguridad. El no seguir las instrucciones podría resultar en heridas y/o daños a su propiedad. Guarde este manual como referen ...

  • Campbell Hausfeld GN0800 - page 15

    15 Sp Manual de Instrucciones NUNCA MANEJE SU GENERADOR BAJO ESTAS CONDICIONES: 1. Tiempo inclemente o lluvioso 2. Vibración excesiva 3. Está echando chispas 4. Falla del motor 5. Disminución de la producción eléctrica 6. Cambio u oscilación de la velocidad del motor 7. Recalentamiento del equipo conectado 8. Tomacorrientes dañados 9. Partes ...

  • Campbell Hausfeld GN0800 - page 16

    16 Sp 2.5 300 600 1000 600 375 250 5 600 1200 500 300 200 125 7.5 900 1800 350 200 125 100 Amperios Vatios Vatios Cable Cable Cable Cable Cable 120 V 220 V #8 #10 #12 #14 #16 CORDONES DE EXTENSION LONGITUD M Á XIMA RECOMENDADA (EN PIES) Funcionamiento (Continuaci ó n) Computadora 300 Reproductor de CD 100 Videograbadora 100 Radio 100 Televisión ...

  • Campbell Hausfeld GN0800 - page 17

    17 Sp Manual de Instrucciones que pueda estar presente. Revise si hay decoloración, la bujía debe ser de color tostado. Verifique la luz; ésta debe ser de 0,7 a 0,8 mm. 3. Vierta aproximadamente una cucharadita de aceite dentro del orificio de la bujía 4. Tire el cordón de arranque varias veces para distribuir el aceite por todo el cilindro. 5 ...

  • Campbell Hausfeld GN0800 - page 18

    18 Sp Cero producción de los tomacorrientes Baja producción de voltaje sin carga 6 Vac o más Menos de 6 Vac Alta producción de voltaje sin carga Baja producción de votaje con carga Producción errática de voltaje Funcionamiento ruidoso Engine won’t start 1. La velocidad del motor es demasiado baja 2. Open or shorted wiring 3. Falla del cond ...

  • Campbell Hausfeld GN0800 - page 19

    19 Sp Manual de Instrucciones Garantía Limitada 1. DURACIÓN: Noventa (90) días a partir de la fecha de compra del comprador original. Las unidades usadas, con fines de alquiler industriales o comerciales están garantizadas durante 90 días a partir de la fecha de compra. 2. QUIEN DA ÉSTA GARANTÍA (EL GARANTIZADOR): Campbell Hausfeld / Scott F ...

  • Campbell Hausfeld GN0800 - page 20

    Notas ...

Manufacturer Campbell Hausfeld Category Portable Generator

Documents that we receive from a manufacturer of a Campbell Hausfeld GN0800 can be divided into several groups. They are, among others:
- Campbell Hausfeld technical drawings
- GN0800 manuals
- Campbell Hausfeld product data sheets
- information booklets
- or energy labels Campbell Hausfeld GN0800
All of them are important, but the most important information from the point of view of use of the device are in the user manual Campbell Hausfeld GN0800.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Campbell Hausfeld GN0800, service manual, brief instructions and user manuals Campbell Hausfeld GN0800. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Campbell Hausfeld GN0800.

A complete manual for the device Campbell Hausfeld GN0800, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Campbell Hausfeld GN0800 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Campbell Hausfeld GN0800.

A complete Campbell Hausfeld manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Campbell Hausfeld GN0800 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Campbell Hausfeld GN0800, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Campbell Hausfeld GN0800, that we can find in the current document
3. Tips how to use the basic functions of the device Campbell Hausfeld GN0800 - which should help us in our first steps of using Campbell Hausfeld GN0800
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Campbell Hausfeld GN0800
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Campbell Hausfeld GN0800 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Campbell Hausfeld GN0800?

Use the form below

If you did not solve your problem by using a manual Campbell Hausfeld GN0800, ask a question using the form below. If a user had a similar problem with Campbell Hausfeld GN0800 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)