Manual Bunn JDF-2

22 pages 0.27 mb
Download

Go to site of 22

Summary
  • Bunn JDF-2 - page 1

    INST ALLA TION & OPERA TING MANUAL JDF-2 BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644 www .bunnomatic.com BUNN ® 35303.0000 12/03 ©2003 Bunn-O-Matic Corporation ...

  • Bunn JDF-2 - page 2

    2 BUNN-O-MA TIC COMMERCIAL PRODUCT W ARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor. 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years parts and 1 year l ...

  • Bunn JDF-2 - page 3

    3 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27442.0000 00986.0002 33461.0001 ! W ARNING DO NO T O VERLOAD CIRCUIT . AL W A YS ELECTRICALL Y GROUND THE CHASSIS OR AD APT ...

  • Bunn JDF-2 - page 4

    4 PLUMBING REQUIREMENTS This dispenser must be connected to a COLD WATER system with operating pressure between 20 and 100 psi (138 and 690 kPa). This water source must be capable of producing a minimum flow rate of 3 fluid ounces (88.7 milliliters) per second. A shut off valve should be installed in the line before the dispenser. Install a regulat ...

  • Bunn JDF-2 - page 5

    5 number .]) BUNN-O-MA TIC does not recommend the use of saddle valves to install the dispenser . The size and shape of the hole(s) made in the supply line(s) by saddle valves may restrict water flow . Note- A water strainer (Bunn-O-Matic part number 23720.1000) should be installed in line, prior to the flexible water line. This strainer is supplie ...

  • Bunn JDF-2 - page 6

    6 LOADING Frozen Concentrates 1. Thaw the frozen concentrate in a refrigerated 35-40 degrees F (1.6-4.4 degrees C) environment for 36 to 48 hours before use. 2. Thoroughly mix the thawed concentrate by vigorously shaking the product container. 3. Open the dispenser door. 4. Prior to placing the product container in the dispenser, make sure that the ...

  • Bunn JDF-2 - page 7

    7 OPERA TING CONTROLS Refrigeration Switch The refrigeration switch is located on the top of the dispenser near the left rear corner. This switch controls power to the compressor and the condenser fan motor. Sanitize Switch The sanitize switch is located behind the drip tray in the lower left corner of the chassis. The drip tray can be removed to p ...

  • Bunn JDF-2 - page 8

    8 OPERATING CONTROLS (cont.) FIG 5 Press and Hold Models A. Product Dispense Switch Pressing and holding switch will initiate product flow from the respective nozzle; releasing the switch will stop the flow. B. Hidden Switch These switches are used to access, change and exit the dispenser program mode. C. Lock Switch This switch is used to lockout ...

  • Bunn JDF-2 - page 9

    9 DISPENSER USE Press and Hold Models (Refer to Fig 5) 1. Place a cup on the drip tray beneath the desired dispensing nozzle. 2. Press and hold the “Product Dispense” switch until the beverage reaches the desired level, then release. Portion Control Models (Refer to Fig 6) 1. Place a cup on the drip tray beneath the desired dispensing nozzle. 2 ...

  • Bunn JDF-2 - page 10

    10 CLEANING & PREVENTIVE MAINTENANCE General Cleaning and Sanitizing Procedures Note: The Bunn Juice Dispenser incorporates a rinse reminder feature which lights the rinse led on the front panel when it is time to rinse. See dip switch function list to activate this feature. Daily: Rinse Procedure Tools required: 32 oz. (946 ml) minimum empty c ...

  • Bunn JDF-2 - page 11

    11 CLEANING (cont) 6. Select the dispense stations by pressing the “Dispense Switch” for that station. Use the “+/Stop Switch” for portion contol dispensers. The “REFILL” indicator will light and the beeper will sound for the dispense head selected. 7. Once the dispense heads have been selected, press and hold the “Sanitize Switch” ...

  • Bunn JDF-2 - page 12

    12 Monthly: Clean Condenser Air Filter 1. Remove the condenser air filter located on the rear of the dispenser. 2. Using a water spray, clean the air filter. Annually: Replace Pump Tubing 1. Open dispenser door. 2. Remove all product containers and place them in a refrigerated (35-40 degrees F [1.6-4.4 degrees C]) environment. Disconnect all connec ...

  • Bunn JDF-2 - page 13

    13 ADJUSTMENT & OPTIONAL SETTINGS SETTING THE MIX RATIO/BRIX Ratio Cup Method 1. Adjust the water flow as described in Water Flow Testing and Adjustment. 2. Remove the dispense nozzle from the appropriate dispense position. 3. Assemble, lubricate, and install the Flow Separator Assembly (BUNN-O-MATIC part number 32629.0000) into the dispense no ...

  • Bunn JDF-2 - page 14

    14 W ater Flow T esting and Adjustment 1. Enter the “Pump Speed Programming” mode by simultaneously press- ing both “Hidden Switches” Fig 5 or Fig 6. Note that the beeper sounds twice and that the “PROGRAM” indicator begins flashing. 2. Place a graduated measuring cup or the large chamber of the empty brixing cup (BUNN-O-MATIC part numb ...

  • Bunn JDF-2 - page 15

    15 the “Product Dispense” (“+/STOP”) Switch is pressed, the motor speed is decreased by one step (5 RPM.) Note that each step is confirmed by a single flash of the appropriate “REFILL” indicator and a single tone from the beeper. 4. Repeat as necessary at the remaining dispense stations. 5. Exit the “Pump Speed Programming” mode by ...

  • Bunn JDF-2 - page 16

    16 6. If the password is forgotten, it can be reset to “0” (dispenser lockout disabled) as follows: Note: The following procedure also clears the programming and service lockout password. a) Disconnect the dispenser from its power source. b) Place the “Refrigeration Switch” Fig 3, in the OFF (rearward) position. c) While pressing and holdin ...

  • Bunn JDF-2 - page 17

    17 3. To enter the password, proceed as follows: a) Press and hold either “Hidden Switch”. b) In a 5 second period, press and release the “Sanitize Switch” the password number of times. For example: If the password is set to 3, press and release the “Sanitize Switch” 3 times in the 5 second period. c) Release the “Hidden Switch”. d) ...

  • Bunn JDF-2 - page 18

    18 Dispense Fault List “REFILL” indicator Beeper Fault 2 flashes 2 beeps Dispense station locked out. 3 flashes 3 beeps DISPENSE/RINSE sensing fault. 4 flashes 4 beeps DISPENSE/RINSE knob mis-positioned. 5 flashes 5 beeps Pump motor stalled/speed sensor inoperative. All “REFILL” 3 beeps Dispenser locked out. indicators flash 3 times Cooling ...

  • Bunn JDF-2 - page 19

    19 Dip Switch Function List Dip Switch Controls Off On 1 “REFILL” indicator when “concentrate out” is detected. Inactive Active 2 Lockout dispense components when “concentrate out” is detected. Inactive Active ( Note ) 3 Number of positions that can dispense/rinse simultaneously. 3 2 4 Rinse timer Off On 5 Audio feedback during dispense ...

  • Bunn JDF-2 - page 20

    20 COOLANT SCHEMA TIC DIAGRAM CONDENSER SUCTION A CCUMULA TOR COMPRESSOR EV APORA T OR PROCESS TUBE 33464.0000A 09/00 ©2000 Bunn-O-Matic Corporation FIL TER DR YER 35303 012703 ...

  • Bunn JDF-2 - page 21

    21 SCHEMA TIC WIRING DIAGRAM 35303 121203 J3-1 J3-2 J1-1 J1-5 J1-10 C O N T R O L P C B O A R D J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 LAMP ASSY. GRN GRN GRN N L1 BLU BRN/BLK RED/BLK RED/BLK GRY WHI BLK LIMIT THERMOSTAT K2 K2 COMP. COMPRESSOR ASSEMBLY + – RECT TRANSFORMER WHI/BLU WHI WHI WHI WHI/RED WHI/RED BLK BLK RED/BLK RED/BLK ...

  • Bunn JDF-2 - page 22

    22 SCHEMA TIC WIRING DIAGRAM 35303 121203 J3-1 J3-2 J1-1 J1-5 J1-10 C O N T R O L P C B O A R D J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 LAMP ASSY. GRN GRN GRN BLU BRN/BLK RED/BLK RED/BLK GRY WHI BLK LIMIT THERMOSTAT K2 K2 COMP. COMPRESSOR ASSEMBLY + – RECT TRANSFORMER WHI/BLU WHI WHI WHI WHI/RED WHI/RED BLK BLK RED/BLK RED/BLK GRY W ...

Manufacturer Bunn Category Beverage Dispenser

Documents that we receive from a manufacturer of a Bunn JDF-2 can be divided into several groups. They are, among others:
- Bunn technical drawings
- JDF-2 manuals
- Bunn product data sheets
- information booklets
- or energy labels Bunn JDF-2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Bunn JDF-2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Bunn JDF-2, service manual, brief instructions and user manuals Bunn JDF-2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Bunn JDF-2.

Similar manuals

A complete manual for the device Bunn JDF-2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Bunn JDF-2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Bunn JDF-2.

A complete Bunn manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Bunn JDF-2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Bunn JDF-2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Bunn JDF-2, that we can find in the current document
3. Tips how to use the basic functions of the device Bunn JDF-2 - which should help us in our first steps of using Bunn JDF-2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Bunn JDF-2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Bunn JDF-2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Bunn JDF-2?

Use the form below

If you did not solve your problem by using a manual Bunn JDF-2, ask a question using the form below. If a user had a similar problem with Bunn JDF-2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)