English dropdown-ico

Manual Makita AN611

19 pages 1.28 mb
Download

Go to site of 19

Summary
  • Makita AN611 - page 1

    Construction Coil Nailer 4.5 - 8.5 kgf/cmZG (65 - 120 PSIG) MODEL AN61 1 300 - 400 PCS. 32 mm, 38 mm, 45 mm, 50 mm, 57 mm, 65 mm (1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2") INSTRUCTION MANUAL SPECIFICATIONS Air pressure I Applicable length I Nail capacity Min. hose diameter Dimensions (L x W x H) Net weight 6.5 mm (1/ ...

  • Makita AN611 - page 2

    IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING THIS TOOL, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. For personal safety and proper operation and main- tenance of the tool, read this instruction manual carefully before using the tool. *Always wear safe ...

  • Makita AN611 - page 3

    General Tool Handling Guidelines: 1. Always assume that the tool contains fasteners. 2. Do not point the tool toward yourself or anyone whether it contains fasteners or not. 3. Do not actuate the tool unless the tool is placed firmly against the workpiece. 4. Respect the tool as a working implement. 5. No horseplay. 6. Do not hold or carry the tool ...

  • Makita AN611 - page 4

    *Only those involved in the work should be in the vicinity. Children especially must be kept away at all times. There may be local regulations concerning noise which must be complied with by keeping noise levels within prescribed limits. In certain cases, shutters should be used to contain noise. Do not play with the contact element: it prevents ac ...

  • Makita AN611 - page 5

    Never use the tool with other than compressed air. If bottled gas (carbon dioxide, oxgen, nitrogen, hydrogen, air, etc.) or combustible gas (hydrogen, propane, acetylene, etc.) is used as a power source for this tool, the tool will explode and cause serious injury. *Always check the tool for its overall condition and loose screws before operation. ...

  • Makita AN611 - page 6

    Make sure that the trigger is locked when the change lever is set to the LOCK position. Check walls, ceilings, floors, roofing and the like carefully to avoid possible electrical shock, gas leakage, explosions, etc. caused by striking live wires, conduits or gas pipes. Use only nails specified in this manual. The use of any other nails may cause ma ...

  • Makita AN611 - page 7

    Make sure no one is nearby before nailing. Never attempt to nail from both the inside and outside at the same time. Nails may rip through and/or fly off, presenting a grave danger. Watch your footing and maintain four balance with the tool. Make sure there is no one below when working in high locations, and secure the air hose to prevent danger if ...

  • Makita AN611 - page 8

    Do not leave the loaded tool or the air compressor under pressure for a long time out in the sun. Be sure that dust, sand, chips and foreign matter will not enter the tool in the place where you leave it setting. *Do not point the ejection port at anyone in the When the air hose is connected, do not carry the tool with your finger on the trigger or ...

  • Makita AN611 - page 9

    Stop nailing operations immediately if you notice something wrong or out of the ordinary with the tool. .Always disconnect the air hose and remove all of the nails: 1. When unattended. 2. Before performing any maintenance or repair. 3. Before cleaning a jam. 4. Before moving the tool to a new location. Perform cleaning and maintenance right after f ...

  • Makita AN611 - page 10

    .Do not operate this tool if it does not contain a legible WARNING LABEL. Do not modify tool without authorization from Makita. Ask Makita's Factory or Authorized service center for periodical inspection of the tool. To maintain product SAFETY and RELIABILITY, maintenance and repairs should be performed by Makita Authorized or Factory Service ...

  • Makita AN611 - page 11

    TOOL INSTALLATION INSTRUCTIONS AND USE Selecting compressor The air compressor must comply with the requirements of Select a compressor that has ample pressure and air output to assure cost-efficient operation. The graph shows the relation between nailing frequency, applicable pressure and compressor air output. Thus, for example, if nailing takes ...

  • Makita AN611 - page 12

    Nose adapter CAUTION : Always lock the trigger and disconnect the hose before installing or removing the nose adapter. When nailing workpieces with easily-marred surfaces, use the nose adapter. It is factory installed at the rear of the tool. Attach the nose adapter to the contact arm (see right). When not in use, store the nose adapter at the rear ...

  • Makita AN611 - page 13

    Place the nail coil over the coil support plate. Uncoil enough nails to reach the feed claw. Place the first nail in the driver channel and the second nail in the feed claw. The nail heads must be in the slot in the feeder body. Place other uncoiled nails on feeder body. Close the magazine cap and door after checking to see that the nail coil is se ...

  • Makita AN611 - page 14

    For No. 1 method, set the change lever to the “Intermittent Nailing” position. For No. 2 method, set the change lever to the “Continuous Nailing” position. After using the change lever to change the nailing method, always make sure that the change lever is properly set to the position for the desired nailing method. Air exhaust Air exhaust ...

  • Makita AN611 - page 15

    Never hang the tool on a waist belt or the like. Dangerous accidental firing may result. Nails Handle nail coils and their box care.Jlly. If the nail coils have been handled roughly, they may be out of shape or their connector breaks, causing poor nail feed. Avoid storing nails in a very humid or hot place or place exposed to direct sunlight. .. ...

  • Makita AN611 - page 16

    MAINTENANCE CAUTION: Always be sure that the trigger is locked and the air hose is disconnected from the tool before attempting to perform inspection or maintenance. Maintenance of nailer Always check the tool for its overall condition and loose screws before operation. Tighten as required. Make sure all safety systems are in working order before o ...

  • Makita AN611 - page 17

    When the tool is not to be used for an extended period of time, lubricate the tool using pneumatic tool oil and store the tool in a safe place. Avoid exposure to direct sunlight and/or a humid or hot environment. Maintenance of compressor, air set and air hose After operation, always drain the compressor tank and the air filter. If moisture is allo ...

  • Makita AN611 - page 18

    Keep the air hose away from heat (over 6OoC, over 140°F), away from chemicals (thinner, strong acids or alkalis). Also, route the hose away from obstacles which it may become dangerously caught on during operation. Hoses must also be directed away from sharp edges and areas which may lead to damage or abrasion to the hose. To maintain product SAFE ...

  • Makita AN611 - page 19

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one- year period, return the COMPLETE tool, freig ...

Manufacturer Makita Category Laptop

Documents that we receive from a manufacturer of a Makita AN611 can be divided into several groups. They are, among others:
- Makita technical drawings
- AN611 manuals
- Makita product data sheets
- information booklets
- or energy labels Makita AN611
All of them are important, but the most important information from the point of view of use of the device are in the user manual Makita AN611.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Makita AN611, service manual, brief instructions and user manuals Makita AN611. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Makita AN611.

Similar manuals

A complete manual for the device Makita AN611, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Makita AN611 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Makita AN611.

A complete Makita manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Makita AN611 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Makita AN611, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Makita AN611, that we can find in the current document
3. Tips how to use the basic functions of the device Makita AN611 - which should help us in our first steps of using Makita AN611
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Makita AN611
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Makita AN611 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Makita AN611?

Use the form below

If you did not solve your problem by using a manual Makita AN611, ask a question using the form below. If a user had a similar problem with Makita AN611 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)