Manual Craftsman 316.794830

36 pages 4.86 mb
Download

Go to site of 36

Summary
  • Craftsman 316.794830 - page 1

    Operator's Manual 4-Cycle GAS SUITCASE BLOWER Model No. 316.794830 INCREDI.PULL UNBELIEVABLE STARTING EA S E with MAX FIRE,_._II3NITIO N M • SAFETY • ASSEMBLY • OPERATION • MAINTENANCE • PARTS LIST • ESPAI_IOL, P. E1 CAUTION: Before using this product, read this manual and follow all safety rules and operating instructions. Sears, ...

  • Craftsman 316.794830 - page 2

    TABLE OF CONTENTS Rules forSafe Operation ................................. 2 Warranty Information ................................... 4 Know Your Unit ........................................ 5 Assembly Instructions ................................... 6 Oil and Fuel Information ................................. 7 Starting/Stopping Instructions ... ...

  • Craftsman 316.794830 - page 3

    • Add fuel in a clean, well-ventilated outdoor area where there are no sparks or flames. Slowly remove the fuel cap only after stopping engine. Do not smoke while fueling or mixing fuel. Wipe up any spilled fuel from the unit immediately. Always wipe unit dry before using. • Move the unit at least 30 feet (9.1 m) from the fueling source and sit ...

  • Craftsman 316.794830 - page 4

    • SAFETY AND INTERNATIONAL SYMBOLS • This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. SYMBOL MEANING • AFETY ALERT SYMBOL Indicates danger, warning or caution. ...

  • Craftsman 316.794830 - page 5

    APPLICATIONS Cleaning yards, garages, driveways, porches, patios, around walls, fences and more. On/Off Stop Control Variable Speed Cruise Control Trigger Handle Air Filter Cover / Starter Rope Grip Spark Plug Blower Tube Muffler Cover Concentrator Curved_/ / Primer Bulb Oil Filler Cap Red Choke Lever Fuel Cap / ...

  • Craftsman 316.794830 - page 6

    ASSEMBLING UNIT Installing Blower Tube WARNING: To prevent serious personal injury, stop theor removingengine andtubes.a ow the mpe er to stop before attach ng _ll WARNING: To prevent serious personal injury or I damage to the unit, the blower tube must be installed I while operating this unit. 1. Align the bump on the end of the blower tube with t ...

  • Craftsman 316.794830 - page 7

    WARNING: OVERFILLING OIL CRANKCASE MAY I CAUSE SERIOUS PERSONAL INJURY. Check and I maintain the proper oil level in the crank case; it is important and cannot be overemphasized. Check the oil before each use and change it as needed. See Changing the Oil. RECOMMENDED OIL TYPE Using the proper type and weight of oil in the crankcase is extremely imp ...

  • Craftsman 316.794830 - page 8

    I_ I WARNING: Operate this unit only in a well- I ventilated outdoor area. Carbon monoxide exhaust fumes can be lethal in a confined area. WARNING: Avoid accidental starting. Make sure you are in the starting position when pulling the starter rope (Fig. 13). To avoid serious injury, the operator and unit must be in a stable position while starting. ...

  • Craftsman 316.794830 - page 9

    HOLDING THE BLOWER WARNING: After starting the unit, always stand on the left side of the unit to operate it as shown in figure 15 to keep from blocking the air intake. Before operating the unit, stand in the operating position. Check for the following: • Operator is wearing proper clothing, such as boots, safety glasses or goggles, ear/hearing p ...

  • Craftsman 316.794830 - page 10

    WARNING: To prevent serious injury, never perform maintenance or repairs with unit running. Always service and repair a cool unit. Disconnect the spark plug wire to ensure that the unit cannot start. MAINTENANCE SCHEDULE Perform these required maintenance procedures at the frequency stated in the table. These procedures should also be a part of any ...

  • Craftsman 316.794830 - page 11

    AIR FILTER MAINTENANCE I_ I WARNING: To avoid serious personal injury, always I turrniYou_.unt off and a ow tto coo before you cean or Cleaning the Air Filter Clean and re-oil the air filter every 10 hours of operation. It is an important item to maintain. Failure to maintain the air filter will VOID the warranty. 1. Open the air filter cover. Push ...

  • Craftsman 316.794830 - page 12

    IDLE SPEED ADJUSTMENT The idle speed of the engine is adjustable. An idle adjustment screw is between the air filter cover and the engine starter housing (Fig. 27). NOTE: Careless adjustments can seriously damage your unit. A Sears or other qualified service dealer should make carburetor adjustments. Check Fuel Old fuel is usually the reason for im ...

  • Craftsman 316.794830 - page 13

    The recommended clearance for both intake and exhaust is .003 - .006 in. (.076 - 0.152 mm). Use a standard automotive .005 in. (0.127 mm) feeler gauge. The feeler gauge should slide between the rocker arm and valve stem with a slight amount ofresistance, without binding. See Figures 30 and 31. 8. If the clearance is not within specification: a. Tur ...

  • Craftsman 316.794830 - page 14

    CAUSE Empty gasoline tank Primer bulb wasn't pressed enough Old gasoline Fouled spark plug Plugged spark arrestor CAUSE Air filter is plugged Old fuel CAUSE Old gasoline Dirty air filter Plugged spark arrestor CAUSE Old gasoline Fouled spark plug Plugged spark arrestor ACTION Fill fuel tank with new gasoline Press primer bulb fully and slowly ...

  • Craftsman 316.794830 - page 15

    Owners Warranty Responsibilities As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your operator's manual. Sears recommends that you retain all receipts covering maintenance on your small off-road engine, but Sears cannot deny warranty solely for the lack of receipts or for your f ...

  • Craftsman 316.794830 - page 16

    ...

  • Craftsman 316.794830 - page 17

    Manual del Operador 4-Ciclos SOPLADOR A GASOLINA Modelo No. 316.794830 INCREDI.PULL_ '_ UNBELIEVABLE STARTING EA S E with MAX FIR_'_INNITIEIN TM • SEGURIDAD • ASSEMBLAJE • OPERACION • MANTENIMIENTO • LISTA DE PIEZAS PRECAUCION: Antes de utilizar este producto, lea este manual y siga todas las reglas de seguridad y las instruccio ...

  • Craftsman 316.794830 - page 18

    Los simbolos de seguridad se utilizan para Ilamar su atencion sobre posibles peligros. Los simbolos de seguridad y sus explicaciones merecen toda su atencion y comprension. Los simbolos de seguridad no eliminan ningQn peligro por si mismos. Las instrucciones o advertencias que ofrecen no substituyen las medidas adecuadas deprevencion de accidentes. ...

  • Craftsman 316.794830 - page 19

    ADVERTENCIAS DE SEGURIDAD PARA LOS RECORTADORES A GASOLINA ADVERTENCIA: La gasolina es muy inflamable y I sus gases pueden explotar si se encienden. Tome las I siguientes precauciones: • Guarde el combustible en envases que hayan sido dise_ados y aprobados para el almacenamiento de dichos materiales. • Evite crear una fuente de encendido por co ...

  • Craftsman 316.794830 - page 20

    • SIMBOLOS DE SEGURIDAD E INTERNACIONALES • Este manual del operador describe los simbolos y figuras de seguridad e internacionales que pueden aparecer en este producto Lea el manual del operador para obtener informacion completa acerca de la seguridad, ensamble, operacion y mantenimiento y reparacion. SIMBOLO SIGNIFICADO SIMBOLO SIGNIFICADO ? ...

  • Craftsman 316.794830 - page 21

    APLICAClON Limpieza de jardines, cocheras, entradas de autom6viles, p6rticos, patios, alrededor de paredes, cercos, etc. Gatillo Control de encendido y apagado Control de crucero de velocidad variable Manija Cubierta del filtro de aire Cuerda de arranque Bujia de encendido Tubo del soplador Tubo curvado Boquilla concentradora Cubierta del silenci ...

  • Craftsman 316.794830 - page 22

    ENSAMBLE DE LA UNIDAD Instalacibn del Tubo de la Sopladora _ DVERTENCIA: Para evitar graves lesiones I personales, apague el motor y espere que el propulsor se detenga antes de conectar o retirar los tubos. _ DVERTENCIA : Para evitar graves lesiones I personales y el dafio de la unidad, el tubo del soplador debe estar instalado mientras opere esta ...

  • Craftsman 316.794830 - page 23

    ADVERTENClA: EL LLENAR DEMASIADO EL CARTER PUEDE CAUSAR LESIONES PERSONALES GRAVES No podemos exagerar la importancia del control y mantenimiento del nivel correcto de aceite en el cigQefial. Verifique el aceite antes de cada uso y cfimbielo cuando sea necesario segQn se indica en la seccion de Cambio del aceite. TIPO DE ACEITE RECOMENDADO El uso d ...

  • Craftsman 316.794830 - page 24

    ADVERTENClA: Use esta unidad solo en un Area exterior bien ventilada. Los gases de escape de monoxido de carbono pueden ser letales en un Area cerrada. ADVERTENClA: Evite los arranques accidentales. Coloquese en posicion de inicio cuando tire de la cuerda de arranque (Fig. 15 o 16). El operador y la unidad deben estar en una posicion estable al arr ...

  • Craftsman 316.794830 - page 25

    SOSTENIMIENTO DE LA SOPLADORA/ASPIRADORA I ADVERTENCIA: Despu6s de arrancar la unidad, I parese siempre en el lado izquierdo de la unidad para operarla, tal como se muestra en la Figura 20. Antes de operar esta unidad, parese en la posicion de operacion. Verifique Io siguiente: • El operador esta vestido con la ropa apropiada tal como botas, gafa ...

  • Craftsman 316.794830 - page 26

    PROGRAMA DE MANTENIMIENTO ADVERTENCIA: Para evitar lesiones personales graves, nunca realice mantenimiento ni reparaciones con la unidad funcionando. Realice siempre el mantenimiento y las reparaciones con la unidad fria. Desconecte el cable de la bujia de encendido para cerciorarse de que la unidad no arrancar& Estos procedimientos requeridos ...

  • Craftsman 316.794830 - page 27

    aproximadamente en la parte superior de la etiqueta de la botella (Fig. 20). Mida el nivel con la varilla de medicion. Si el nivel estfi bajo, agregue una pequefia cantidad de aceite y vuelva a medir (Fig. 17). No Io Ilene demasiado. 5. Vuelva a colocar el tapon de relleno de aceite/varilla de medicion. 6. Vuelva a conectar el manguito de la bujia ...

  • Craftsman 316.794830 - page 28

    Limpieza del Filtro de Aire La condici6n del filtro de aire es importante para el funcionamiento de la unidad. Un filtro de aire sucio limitara el flujo de aire y cambiara la mezcla de aire y combustible. Con frecuencia esto se confunde con un carburador fuera de ajuste. Inspeccione la condicion del filtro de aire antes de ajustar el tornillo de ve ...

  • Craftsman 316.794830 - page 29

    8. Si el huelgo no se encuentra dentro de las especificaciones: a. Gire la tuerca de ajuste con una Ilave de 8 mm (5/16 pulgadas) o una guia de tuercas (Fig. 31). • Para incrementar el huelgo, gire la tuerca de ajuste en sentido antihorario. • Para reducir el huelgo, gire la tuerca de ajuste en sentido horario. b.Vuelva a inspeccionar ambos hue ...

  • Craftsman 316.794830 - page 30

    CAUSA El tanque de gasolina esta vacio La bombilla de cebado no fue oprimida Io suficiente La gasolina es viejo La bujia de encendido esta arruinada Parachispas obstruido CAUSA El filtro de aire esta obstruido La gasolina es viejo CAUSA La gasolina es viejo El accesorio de corte esta atascado de hierba El filtro de aire esta sucio Parachispas obstr ...

  • Craftsman 316.794830 - page 31

    tenga los recibos ni porque usted no pueda asegurar que se ha realizado todo el mantenimiento programado. • Sin embargo, como propietario del motor "off-road" pequefio, usted deber& estar consciente de que Sears pudiera denegarle cobertura de la garantia si su motor "off-road" pequefio o una pieza del mismo ha presentado f ...

  • Craftsman 316.794830 - page 32

    E16 ...

  • Craftsman 316.794830 - page 33

    E17 ...

  • Craftsman 316.794830 - page 34

    REPLACEMENT PARTS - MODEL 316.794830 4-CYCLE GAS BLOWER Item Part No. Description 1 753-05246 Muffler Screws 2 753-05900 Muffler Assembly (includes 1 & 3) 3 753-05244 Muffler Gasket 4 791-181025 Screw 5 753-05901 Rocker Cover 6 753-05902 O-Ring 7 791-181003 Screw 8 753-05903 Throttle Cable 9 753-05673 Insulator Gasket 10 753-05248 Nut 11 753-05 ...

  • Craftsman 316.794830 - page 35

    REPLACEMENT PARTS - MODEL 316.794830 4-CYCLE GAS BLOWER Item Part No. 1 753-05917 2 753-05918 3 753-04595 4 753-05919 5 753-05920 6 753-05926 7 753-05927 8 753-05928 9 753-05929 10 753-05930 11 791-181003 12 753-05931 13 753-05924 Description Intake Cover Spring Screw Handle Grips Impeller Housing (includes 4) Latch Tube Nut Washer Impeller Throttl ...

  • Craftsman 316.794830 - page 36

    Your Home For expert troubleshooting and home solutions advice: www.managemyhome.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For ...

Manufacturer Craftsman Category Blower

Documents that we receive from a manufacturer of a Craftsman 316.794830 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 316.794830 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 316.794830
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 316.794830.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 316.794830, service manual, brief instructions and user manuals Craftsman 316.794830. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 316.794830.

Similar manuals

A complete manual for the device Craftsman 316.794830, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 316.794830 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 316.794830.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 316.794830 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 316.794830, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 316.794830, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 316.794830 - which should help us in our first steps of using Craftsman 316.794830
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 316.794830
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 316.794830 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 316.794830?

Use the form below

If you did not solve your problem by using a manual Craftsman 316.794830, ask a question using the form below. If a user had a similar problem with Craftsman 316.794830 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)