Manual Multiquip HTXD6i / STXD6i

32 pages 2.59 mb
Download

Go to site of 32

Summary
  • Multiquip HTXD6i / STXD6i - page 1

    SETUP , ADJUSTMENTS AND CALIBRA TIONS THIS MANU AL MUST A CCOMP ANY THE EQ UIPMENT A T ALL TIMES. T o find the latest re vision of this publication, visit our website at: www .m ultiquip.com SERIES MODEL HTXD6i/STXD6i HYDRAULIC RIDE-ON TROWEL (Y ANMAR 4TNV84T -Z-DSA2 DIESEL ENGINE) Re vision #1 (01/24/14) PN: 32399 ...

  • Multiquip HTXD6i / STXD6i - page 2

    P A GE 2 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) T ABLE OF CONTENTS HTX6Di/STX6Di T r owel Machine Inf ormation And Maintenance Log ............ 3 Saf ety Inf ormation ................................................ 4-9 T ools Needed ......................................................... 10 Ma ...

  • Multiquip HTXD6i / STXD6i - page 3

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 3 MACHINE INFORMA TION AND MAINTENANCE LOG T echnician__________________________________ e Date:___________________________ Machine Inf ormation MODEL LH Motor Serial No. Machine Serial No. RH Motor Serial No. Engine Serial No. Program ID Pump Serial ...

  • Multiquip HTXD6i / STXD6i - page 4

    P A GE 4 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) Do not operate or service the equipment before reading the entire manual. Saf ety precautions should be f ollow ed at all times when operating this equipment. F ailure to read and understand the safety messages and operating instructions could resul ...

  • Multiquip HTXD6i / STXD6i - page 5

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 5 GENERAL SAFETY CA UTION  NEVER operate this equipment without proper protectiv e clothing, shatter proof glasses, respiratory protection, hearing protection, steel-toed boots and other protective de vices required by the job or city and state reg ...

  • Multiquip HTXD6i / STXD6i - page 6

    P A GE 6 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) TRO WEL SAFETY D ANGER  Engine fuel e xhaust gases contain poisonous carbon mono xide. This gas is colorless and odor less, and can cause death if inhaled.  The engine of this equipment requires an adequate free fl ow of cooling air . NEVER o ...

  • Multiquip HTXD6i / STXD6i - page 7

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 7 NO TICE  NEVER run engine without an air fi lter or with a dir ty air fi lter . Sev ere engine damage may occur . Ser vice air fi lter frequently to pre v ent engine malfunction.  NEVER tamper with the f actor y settings of the engine or en ...

  • Multiquip HTXD6i / STXD6i - page 8

    P A GE 8 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) TRANSPORTING SAFETY CA UTION  NEVER allow an y person or animal to stand underneath the equipment while lifting.  Ride-on trowels are v er y heavy and awkw ard to mov e around. Use proper heavy lifting procedures and DO NO T attempt to lift th ...

  • Multiquip HTXD6i / STXD6i - page 9

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 9  T railer should be adjusted to a le v el position at all times when towing.  Raise and lock tr ailer wheel stand in up position when towing.  Place choc k blocks underneath wheel to prev ent rolling while parked.  Place suppor t bloc ks ...

  • Multiquip HTXD6i / STXD6i - page 10

    P A GE 10 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) TOOLS NEEDED The specialized tools listed in T able 1 are required to maintain and service the HTXD6i and STXD6i r ide-on trow els. Fleet technicians and ser vicing dealers must ha v e these tools f or efficient unit setup and component calibratio ...

  • Multiquip HTXD6i / STXD6i - page 11

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 11 MACHINE INFORMA TION MODEL 1 . Enter appropriate model:  HTXD6i — f or 6-blade HTX  STXD6i — f or 6-blade STX SERIAL NUMBER 2 . Mac hine Serial Number — as shown on serial tag. 3 . Engine Serial Number — located on top of engine (E/N) ...

  • Multiquip HTXD6i / STXD6i - page 12

    P A GE 12 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) GENERAL PROCEDURES SETUP JUMPER INST ALLA TION 1 . Remo v e Cap (PN: 22812) on P24 of main har ness (under f oot platf orm). 2 . Install Setup J umper (P/N: 32007 on P24). NO TICE These general procedures will be ref erenced in other sections thro ...

  • Multiquip HTXD6i / STXD6i - page 13

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 13 INITIAL CHECK AND ADJUSTMENTS PRELIMINAR Y CHARGE PRESSURE ADJUSTMENT 1 . Loosen 1-1/16" jam n ut on charge relief v alve (Item A, Figure 5). 2 . Use a 1/2" soc k et to adjust the small he x nut within the larger he x jam nut (Item B , Fi ...

  • Multiquip HTXD6i / STXD6i - page 14

    P A GE 14 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) Engine Oil 1 . Ensure engine is le vel. 2 . Remo v e the oil filler cap (top or side). See Figure 7. Figure 7. Adding Engine Oil 3 . Add the required amount of engine oil at the top or side engine oil filler por t. 4 . W ait 3 minutes then procee ...

  • Multiquip HTXD6i / STXD6i - page 15

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 15 SER VICE TOOL SETUP AND CONNECTION WHITEMAN SER VICE TOOL (WST) INST ALLA TION 1 . Call or e-mail Multiquip T echnical Suppor t or Field Ser vice to obtain the application specific Whiteman Ser vice T ool (WST) file. 2 . Also obtain softw are lic ...

  • Multiquip HTXD6i / STXD6i - page 16

    P A GE 16 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) 9 . The ne w screen will ha v e both na vigation and tool bars active (Figure 13.) Figure 13. WST T ool Bar 10. Click on "T ools". On the drop-down men u, clic k on "License Manager" (Figure 14). Figure 14. WST License Manager 1 ...

  • Multiquip HTXD6i / STXD6i - page 17

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 17 LAPTOP CONFIGURA TION CONNECTION PROCEDURE 1 . Plug the CAN Gate wa y cable to the trow el at the ser vice por t (Figure 16). Do not connect laptop at this time. Figure 16. CAN Gateway Cab le to Service P ort 2 . On the tro wel, turn the ignition k ...

  • Multiquip HTXD6i / STXD6i - page 18

    P A GE 18 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) MACHINE SETUP AND CALIBRA TION CALIBRA TE FOOT PED AL 1 . T ur n key to ON position b ut DO NOT star t machine. 2 . Clic k “CALIBRA TION” button on machine setup page. 3 . Clic k “CALIBRA TION” button in "PED AL SENSOR" frame (Fig ...

  • Multiquip HTXD6i / STXD6i - page 19

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 19 MACHINE SETUP AND CALIBRA TION Calibration 1 . Set sensor z ero position def ault: a . Ensure that f oot pedal is fully released. b. Read % SENSOR V OL T A GE. c . Round % Sensor V oltage value to nearest percent and enter in CALB POINT 1 DEF A UL ...

  • Multiquip HTXD6i / STXD6i - page 20

    P A GE 20 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) MA CHINE PRESSURE ADJUSTMENT Charge Pressure Adjustment 1 . Disab le cold star t. 2 . With machine off , install gauge capable of reading 300 psi to Charge Or Pitch pressure test por t (Figure 27). Figure 27. Pressure T est P or ts Location 3 . Res ...

  • Multiquip HTXD6i / STXD6i - page 21

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 21 MACHINE SETUP AND CALIBRA TION 8 . Return engine r pm to idle. 9 . T ur n off machine and remove gauge . Pitch Pressure Adjustment 1 . Disab le cold star t. 1 . Increase engine rpm to full operating RPM. 2 . Loosen 3/4" jam n ut on pitch relie ...

  • Multiquip HTXD6i / STXD6i - page 22

    P A GE 22 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) 8 . Retighten jam n ut. 9 . Return engine to idle. 10. T urn off machine and remove gauge . 11. Record Pressure on Machine Information and Maintenance Log. 12. Re-enable cold star t. TRO WEL SPEED ADJUSTMENTSETUP Adjust Zero Str oke P osition 1 . ...

  • Multiquip HTXD6i / STXD6i - page 23

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 23 MACHINE SETUP AND CALIBRA TION 5 . Re-measure speed, repeating steps 2 and 3 until Left Side T rowel Speed is correct: a . HTXD6i — 157 to 160 RPM (942 to 960 Pulses per minute) b. STXD6i— 127 to 130 RPM (762 to 780 Pulses per minute) 6 . Recor ...

  • Multiquip HTXD6i / STXD6i - page 24

    P A GE 24 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) 6 . Set Sensor z ero position def ault: a . Ensure f oot pedal is fully released. b. Read % Sensor V oltage (Figure 35). Figure 35. Star t Stroke Sensor Calibration c . Round value to nearest percent and enter in CALB POINT 1 DEF A UL T . d . Press ...

  • Multiquip HTXD6i / STXD6i - page 25

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 25 MACHINE SETUP AND CALIBRA TION Measure Blade Leading Edge Height 1 . Fully pitch machine b y pressing and holding T win pitch up button until pitch cylinders fully e xtended. 2 . Choose a b lade on both LH and RH Rotor . Using Gauge P/N 32044, meas ...

  • Multiquip HTXD6i / STXD6i - page 26

    P A GE 26 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) Set Zero Pitc h Cylinder Stops 1 . Flatten b lades (bottom out the pitch cylinders). 2 . T ur n machine off. 3 . Remo v e cle vis pin (Item E, Figure 39) from pitch cylinder allowing y oke (Item B, Figure 39) to rest on thrust collar . Figure 39. Z ...

  • Multiquip HTXD6i / STXD6i - page 27

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 27 b. Install 3.25” Gauge (P/N 32044) o v er both Left and Right Cylinders as shown in Figure 41. Figure 41. Gaug e Installation c . Press Hard Ret. button to retract cylinder onto gauge. d . V er ify gauge is tight between cylinder body and cle vis ...

  • Multiquip HTXD6i / STXD6i - page 28

    P A GE 28 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) INSPECTION FLUID LEVELS Record the f ollowing fluid le vels on Machine Inf ormation and Maintenance Log in Inspection section. Refer to Fluid Fill and Check section f or procedure.  Engine Oil  Engine Coolant  Hydraulic Oil MECHANICAL 1 . ...

  • Multiquip HTXD6i / STXD6i - page 29

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 29 ST A TIC BLADE PITCH DRIFT TEST 1 . Switch smart pitch switch to off position. 2 . Bring machine up to temperature. This will be indicated by “Cold Star t” (aux 1) lamp tur ning off. 3 . Choose one b lade from each spider and mark with small X ...

  • Multiquip HTXD6i / STXD6i - page 30

    P A GE 30 — HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) FUSE INFORMA TION T able 3. Fuses Fuse Number Amps Designator Functions Fused 1 20 T13 MCU P ow er T21 Service Port Connector 2 20 T3 Oil Cooler 3 5 T5 Light Switch T15 Pitch Switches 4 20 T6 Left Lights 5 7.5 T23 Spra yers 6 20 T7 Right Lights T a ...

  • Multiquip HTXD6i / STXD6i - page 31

    HTXD6i/STXD6i TRO WEL • SETUP , ADJUSTMENTS AND CALIBRA TIONS — REV . #1 (01/24/14) — P A GE 31 NOTES ...

  • Multiquip HTXD6i / STXD6i - page 32

    SETUP , ADJUSTMENTS AND CALIBRA TIONS Y our Local Dealer is: HERE’S HOW TO GET HELP PLEASE HA VE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING United St a teS Multiquip Corporate Office MQ P arts Depar tment 18910 Wilmington A v e. Carson, CA 90746 Contact: mq@multiquip .com T el. (800) 421-1244 F ax (310) 537-3927 800-427-1244 310-537-3700 F ...

Manufacturer Multiquip Category Battery Charger

Documents that we receive from a manufacturer of a Multiquip HTXD6i / STXD6i can be divided into several groups. They are, among others:
- Multiquip technical drawings
- HTXD6i / STXD6i manuals
- Multiquip product data sheets
- information booklets
- or energy labels Multiquip HTXD6i / STXD6i
All of them are important, but the most important information from the point of view of use of the device are in the user manual Multiquip HTXD6i / STXD6i.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Multiquip HTXD6i / STXD6i, service manual, brief instructions and user manuals Multiquip HTXD6i / STXD6i. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Multiquip HTXD6i / STXD6i.

Similar manuals

A complete manual for the device Multiquip HTXD6i / STXD6i, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Multiquip HTXD6i / STXD6i by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Multiquip HTXD6i / STXD6i.

A complete Multiquip manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Multiquip HTXD6i / STXD6i - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Multiquip HTXD6i / STXD6i, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Multiquip HTXD6i / STXD6i, that we can find in the current document
3. Tips how to use the basic functions of the device Multiquip HTXD6i / STXD6i - which should help us in our first steps of using Multiquip HTXD6i / STXD6i
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Multiquip HTXD6i / STXD6i
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Multiquip HTXD6i / STXD6i in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Multiquip HTXD6i / STXD6i?

Use the form below

If you did not solve your problem by using a manual Multiquip HTXD6i / STXD6i, ask a question using the form below. If a user had a similar problem with Multiquip HTXD6i / STXD6i it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)