English dropdown-ico

Manual Cisco Systems 500

24 pages 0.71 mb
Download

Go to site of 24

Summary
  • Cisco Systems 500 - page 1

    Quick Start Guide Cisco 500 Series Stackable Managed Switches ...

  • Cisco Systems 500 - page 2

    2 500 Series Stacka ble Managed Switches We l c o m e Thank you f or choosing the Cisco 500 S eries Stackable Managed Switch, a Cisco net work communications devic e. This devic e is designe d to be operational right out of the box as a standar d layer 2 and 3 swit ch. In the fact or y default configuration, it will f or ward packets betwe en conne ...

  • Cisco Systems 500 - page 3

    500 Series Stackable Managed Switches 3 Mounting the Cisc o Stackable Manage d Swi tch There ar e t wo ways to ph ysically install the switch: • Set the switch on a flat surface. • Mount the swit ch in a stan da r d ra ck ( 1 rack unit) . Do not deploy the devic e in a location where any of the f ollowing conditions exist: High Ambient T emp er ...

  • Cisco Systems 500 - page 4

    4 500 Series Stacka ble Managed Switches Reduc e d Air Flow —B oth side panels must be unob struct e d to pr event overheating. Mech anical O verloading — The device should b e level, stable, and secure to pr event it from slidin g or shifting out of po sition. Circuit Overlo ading —Adding the device to the power outlet must not overload that ...

  • Cisco Systems 500 - page 5

    500 Series Stackable Managed Switches 5 C AUTION F or stability , load the rack fr om the b ottom to the t op, with the heaviest device s on the b ottom. A top-heavy rack is lik ely t o be unstable and might tip o ver . C onne cting Net work D evic es T o conne ct the switch t o the network : S TEP 1 Conne ct an Ethernet cable to an Ethernet por t ...

  • Cisco Systems 500 - page 6

    6 500 Series Stacka ble Managed Switches Power over Ethernet (PoE) C onsiderations If your swit ch is one of the PoE mo dels , consider the following table f or specific informati o n: N OTE The swit ch can delive r a maximum of 15.4 W at ts to an y 10/ 100 Gigabit PoE port . SF500 -24M P , SF500 -48MP , SG5 00X -24MPP , and SG50 0X -48MP can deliv ...

  • Cisco Systems 500 - page 7

    500 Series Stackable Managed Switches 7 phones , IP cam eras, and wireles s ac ce s s po ints . The PoE switches can det e ct and supply power to pre-standar d legacy PoE Powered Devices . Due to th e suppor t of legacy PoE, it is pos sible that a PoE switch acting as a PSE may mistakenly det ect and supply power to an attaching PSE , including oth ...

  • Cisco Systems 500 - page 8

    8 500 Series Stacka ble Managed Switches When the switch is using the factor y default IP addr es s , the System LED flashes c ontinuously . When the switch is using a DHCP s er ver -as signe d IP address or an administrator has configured a static IP addr es s, the System LED is on solid (DHCP is enabled by default). N OTE If you are managing the ...

  • Cisco Systems 500 - page 9

    500 Series Stackable Managed Switches 9 C AUTION Mak e sure that any configuration changes ma de are saved t o the Star tup co nfiguration befor e exiting from the web-b ase d interface b y clicking on the Sav e icon. Exit ing b ef ore you save y our c onfiguration will result in all current changes being lo st the next time the switch is r eb oote ...

  • Cisco Systems 500 - page 10

    10 500 Series Stacka ble Managed Switches C AUTION Mak e sure that any configuration changes are sav e d befor e exiting by issuing the command: copy running-conf ig startup- config Y ou ar e ready t o c onfigure the switch. R efer to the Cisco 500 S eries Stackable Managed Switch Administration Guide f or fur ther inf ormation. N OTE If you ar e n ...

  • Cisco Systems 500 - page 11

    500 Series Stackable Managed Switches 11 T IP The default stack ports on the 500X ar e X G3/S 1 and X G4/S2. If the correct mo dule is plugged into X G3/S 1 and X G4/S2, the switch should be able t o detect the co nne ction and configure the speed acc ording t o the module capability without any manual configuration. The 5G /S 1 and 5 G/S2 interfac ...

  • Cisco Systems 500 - page 12

    12 500 Series Stacka ble Managed Switches Changing the stack mode of a switch r equires a reboot of the switch. Stack Unit Mo de s Device s can operate in one of the f o llowing Stack Unit modes : •S t a n d a l o n e — The device is not conne cted t o any other device and does not have a stack port . •N a t i v e S t a c k i n g —A device ...

  • Cisco Systems 500 - page 13

    500 Series Stackable Managed Switches 13 Stack C onfiguration Options The f ollowing des cribe s s ome typical stack c onfigurations: Example St acking S c enario s N OTE Spe eds lis ted below that u se xx -auto mean auto-detection of the SFP speed. F or the S G500X - 24, S G500X - 24P , S G 500X -24MPP , SG500X -48, and SG500X -48P , and SG500X -4 ...

  • Cisco Systems 500 - page 14

    14 500 Series Stacka ble Managed Switches • Ports X G 1 and X G2 ar e available as standar d net work por ts –S p e e d — 1 G o r 1 0 G Stacking Option Two: • Po r t s XG 3 / S 1 a n d XG 4 / S 2 a r e n o t a v a i l a b l e • Port S 1 , S2 and 5 G are configured as stack por ts –S p e e d — 1 G , 5 G , 1 G / 5 G - a u t o • Ports ...

  • Cisco Systems 500 - page 15

    500 Series Stackable Managed Switches 15 • Ports S 3 and S4 are a vailable as standard network por ts –S p e e d — 1 G Non-Stacking st andalone option: • Port S 1 /SFP , S2/S FP are a vailable as standard network p o r ts – Speed— 1G or 100M • Ports S 3 and S4 are configur ed as standard networking p or ts –S p e e d — 1 G ...

  • Cisco Systems 500 - page 16

    16 500 Series Stacka ble Managed Switches Ex tern al Fe atur e s of the Cis c o 500 S erie s St ackable Manage d S witch This section de scribe s the exterior of the swit ches including por ts , LEDs , and connectors. F ront Panel The por ts and LEDs are locat e d on the front panel of the swit ch. 500X Lef t Side 500 Lef t Side SG500XG-8F 8T Le ft ...

  • Cisco Systems 500 - page 17

    500 Series Stackable Managed Switches 17 500X Right Side 500 Right Side SG500XG-8F 8T Right Side RJ-45 Ethernet Ports —Us e these por ts to connect net work devices , such as computers, printers, and ac ces s points , to the swit ch. Standard Ethernet por ts can not be use d to stack the swit che s . SFP (if presen t)— The small f orm-factor pl ...

  • Cisco Systems 500 - page 18

    18 500 Series Stacka ble Managed Switches • The 500 and 500X swit ches suppor t the f ollowing SFP+ Copp er Cable modules f or stacking : SFP-H 10 GB-CU 1M, SFP- H 10GB -CU3M, and SFP -H 1 0GB-C U5M . • SFP inter face is a c ombination por t , shared with one other RJ-45 interface. When the S FP is active, th e adjac ent RJ-45 p or t is disable ...

  • Cisco Systems 500 - page 19

    500 Series Stackable Managed Switches 19 Gigabit LED (if present) —(Green) L ocated on the right of a GE port . Lights steady when another device is connected to the por t , is p owered on, and a 1000 Mbps link is e stablished bet ween the devic es . When the LED is of f , the connection spe ed is under 1000 Mbps or nothing is cabled to the port ...

  • Cisco Systems 500 - page 20

    20 500 Series Stacka ble Managed Switches T rouble shoot Y our C onne ction If you cannot acces s your switch fr om the web-b ased inter face, the switch might not be reachable fr om your computer . Y ou can t e st network connections by using ping on a c omputer running Wi ndows: S TEP 1 Open the T erminal application. S TEP 2 Enter the ping comma ...

  • Cisco Systems 500 - page 21

    500 Series Stackable Managed Switches 21 No I P r o u t e : If the switch and your comput er are in differ ent IP subnets , you need one or more r outers t o rout e the packets betwe en the two subnets . U nusua lly long acces s time: Most conne ctions will be available in a f ew s econds . Due to the standard spanning tree loop detection logic, ad ...

  • Cisco Systems 500 - page 22

    22 500 Series Stacka ble Managed Switches Where to Go F rom Her e Suppor t Cisco Supp or t Communit y ww w .cis co.c om/ go/smallbizsuppor t Cisco Supp or t and Res ource s w w w .cisc o.com/ go/ sm allbizhelp Phone Suppor t C ontacts w w w .cisco.c om/ en/US/ supp or t / tsd_cisco_ small_busines s_suppor t_c enter_contacts .html Cisco Firmwar e Do ...

  • Cisco Systems 500 - page 23

    500 Series Stackable Managed Switches 23 ...

  • Cisco Systems 500 - page 24

    Americ as He adquar ters Cisco Systems, Inc . 170 W est T asman Drive San Jose, CA 95134- 1706 USA http ://w w w .cisc o.com Small Business Suppor t US : 1 -866-606 - 1866 Small Busines s Suppor t Global C ontact Numb ers Cisco and the Cisco logo are trademarks or regist ered trademark s of Cisc o and/or its affiliates in the U.S. and other countri ...

Manufacturer Cisco Systems Category Switch

Documents that we receive from a manufacturer of a Cisco Systems 500 can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- 500 manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems 500
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems 500.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems 500, service manual, brief instructions and user manuals Cisco Systems 500. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems 500.

Similar manuals

A complete manual for the device Cisco Systems 500, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems 500 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems 500.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems 500 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems 500, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems 500, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems 500 - which should help us in our first steps of using Cisco Systems 500
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems 500
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems 500 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems 500?

Use the form below

If you did not solve your problem by using a manual Cisco Systems 500, ask a question using the form below. If a user had a similar problem with Cisco Systems 500 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)