English dropdown-ico

Manual Craftsman 536.772101

31 pages 1.04 mb
Download

Go to site of 31

Summary
  • Craftsman 536.772101 - page 1

    3.5 Horsepower 9 Inch EDGER MODEL NO. 536.772101 Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product. SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A. F_)01101M ...

  • Craftsman 536.772101 - page 2

    TABLE OF CONTENTS WARRANTY STATEMENT SAFETY RULES INTERNATIONAL SYMBOLS ASSEMBLY OPERATION MAINTENANCE 2 SERVICE AND ADJUSTMENT 17 3 TROUBLE SHOOTING CHART 20 5 EDGER REPAIR PARTS 21 6 ENGINE REPAIR PARTS 25 10 SPANISH (ESPAI_IOL) 31 14 PARTS AND SERVICE BACK COVER WARRANTY STATEMENT LIMITED ONE-YEAR WARRANTY ON CRAFTSMAN EDGER For one year from th ...

  • Craftsman 536.772101 - page 3

    SAFETY RULES Safe Operation Practices for Edger. WARNING: Look for this symbol to point out important safety precautions. It means: "Attention! Become Alertt Your Safety Is Involved." _lb ARNING: To prevent acciden- tal starting when setting-up, transporting, adjustin9 or mak- ing repairs, always disconnect spark plug wire and put wire wh ...

  • Craftsman 536.772101 - page 4

    Safe Storage • Always refer to the owner's manual instruc- tions for important details if the Edger is to be stored for an extended period. SAFETY RULES spect the Edger for any damage, and re- pair the damage before restarting and operating it. • Never store the Edger with fuel in the fuel tank inside a building where ignition sources are ...

  • Craftsman 536.772101 - page 5

    SAFETY RULES INTERNATIONAL SYMBOLS IMPORTANT: Many of the following symbols are located on your unit or on literature sup- plied with the product. Before you operate the unit, learn and understand the purpose for each symbol. Control And Operating Symbols Slow Fast Fuel Oil Primer Button Safety Warning Symbols WARNING WARNING Thrown Objects. Rotati ...

  • Craftsman 536.772101 - page 6

    ASSEMBLY ASSEMBLY Parts Packed Separately In Carton 1 - Owner's Manual (not shown) 1 - Container Of Oil 2 - Hair Pin 1 - Control Rod 1 - Control Rod 1 - Container of Oil 1 -HairPin _lb WARNING: Always wear safety glasses or eye shields while as, sembling the Edger. Figure 1 shows the Edger completely as- sembled. References to the right or lef ...

  • Craftsman 536.772101 - page 7

    ASSEMBLY HOW TO RAISE THE HANDLE 1. Loosen the knobs and raise the upper handle to the upright position. See Figure 2. 2. Tighten the knobs. Make sure the knobs are to the outside of the handles as shown in Figure 2. 3. Insert the end of the control rod, from RIGHT to LEFT, through the hole in the front wheel arm. Attach with hair pin found in part ...

  • Craftsman 536.772101 - page 8

    ASSEMBLY HOW TO PREPARE THE ENGINE Fill With Oil This Edger was shipped with a 20 ounce container of SAE30 motor oil. Add this oil to the engine before operating. To fill the crank- case, remove the oil fill cap/dipstick and add the SAE30 motor oil. DO NOT OVERFILL. How To Add The Engine Oil 1. Put the Edger on a level surface. 2. Remove the oil fi ...

  • Craftsman 536.772101 - page 9

    ASSEMBLY _" CHECKLIST For the best performance and satisfaction from this quality product, please review the following checklist before you operate the Edger: #-" All assembly instructions have been completed. Check carton. Make sure no loose parts remain in the carton. All fasteners have been properly tight- ened. As you learn how to use ...

  • Craftsman 536.772101 - page 10

    OPERATION KNOW YOUR EDGER READ THE OWNER'S MANUAL AND ALL SAFETY RULES BEFORE YOU OPERATE the Edger. To familiarize yourself with the location of the controls, compare the illustrations with your Edger. Save this manual for future reference. Engine Stop Lever Recoil Starter Handle Depth Control Lever Control Rod Throttle Control Fuel Tank Cap ...

  • Craftsman 536.772101 - page 11

    OPERATION _IL ARNING: When the engine runs, the blade will rotate. To prevent injury, keep hands and feet away from blade. HOW TO STOP THE EDGER 1. Move the depth control lever forward to raise the blade. Then, release the engine stop lever. See Figure 8. _lb WARNING: Never leave the Edger unattended while the en- gine is running. Always raise the ...

  • Craftsman 536.772101 - page 12

    OPERATION HOW TO STOP THE ENGINE To stop the engine, release the engine stop ieven If the engine continues to run, move the throttle control to the STOP position. If the engine will not stop, hold a screwdriver against the spark plug and against the en- gine cooling fins. The spark will go to ground and the engine will stop. HOW TO START THE ENGINE ...

  • Craftsman 536.772101 - page 13

    OPERATION EDGING TIPS • Edging is best performed when conditions are dry. If the soil is to wet, dirt becomes packed around the blade causing prema- ture belt wear and decreased perfor- mance. • If dirt does become packed around the blade, stop the engine and remove the wire from the spark plug. Remove the packed dirt and debris from the blade. ...

  • Craftsman 536.772101 - page 14

    MAINTENANCE CUSTOMER RESPONSIBILITIES SERVICE RECORDS Fill in dates as you Before Every Every Before complete regular Each 10 25 Each Before service. Use Often Hours Hours Season Storage I I Lubdcate All Pivot i = I I Points _/ ' ' ,_/ ' SERVICE DATES Lubricate Wheel Axles I Check Engine Oil ....... Level ,_/ ..... Change Engine Oil ...

  • Craftsman 536.772101 - page 15

    MAINTENANCE LUBRICATION After each 25 hours, apply a small amount of engine oil to all moving parts, particularly the wheels. How To Change The Engine Oil Change the oil in the engine crankcase after each 25 hours of use. NOTE: The oil will drain more freely when the engine is warm. 1. Disconnect the spark plug wire from the spark plug. 2. Remove t ...

  • Craftsman 536.772101 - page 16

    MAINTENANCE SPARK PLUG Check the spark plug every 25 hours. Re- place the spark plug if the electrodes are pitted, burned, or if the porcelain is cracked. moval. Tighten the spark plug to a torque of 15 foot-pounds. 1. Make sure the spark plug is clean. Clean the spark plug by carefully scrap- ing the electrodes (do not sand blast or use a wire bru ...

  • Craftsman 536.772101 - page 17

    SERVICE AND ADJUSTMENT HOW TO REMOVE THE BELT The belt made of a special compound. If the belt becomes worn or breaks, replace the belt with an original equipment belt. 1. Disconnect the spark plug wire from the spark plug. 2. Drain the gasoline and oil from the en- gine. 3. Tip the Edger backwards on the handle. Block the top of the handle against ...

  • Craftsman 536.772101 - page 18

    SERVICE AND ADJUSTMENT HOW TO REPLACE THE BLADE The blade is subject to wear and damage, such as nicks and dents. This will not gener- ally affect its function. The blade is designed to not require sharp- ening. Do not attempt to sharpen the blade. The blade is also reversible. If nicks or dents are excessive, remove the blade and turn it around. T ...

  • Craftsman 536.772101 - page 19

    SERVICE AND ADJUSTMENT STORAGE _1_ WARNING: Never store the Edger indoors with fuel in the fuel tank. Never store in an en- closed, poorly ventilated area where fumes could reach an open flame, a spark or a pilot light as on a furnace, wa- ter heater or clothes dryer. _lb ARNING: Do not remove gas- oline while inside a building, near a fire, or whi ...

  • Craftsman 536.772101 - page 20

    TROUBLE SHOOTING CHART TROUBLE CAUSE Engine difficult to start Stale fuel or Engine runs erratically or Engine will not run at full speed Clogged fuel filter Dirt in fuel tank or out of fuel Carburetor out of adjustment Fouled spark plug Dirty air filter Engine smokes Plugged air filter excessively Clean debris from blade. Cutting blade will not ro ...

  • Craftsman 536.772101 - page 21

    CRAFTSMAN 536.772101 REPAIR PARTS 22 301 305 320 10 321 321 317 318 311 314 316 315 339589C KEY NO. DESCRIPTION 10 3.5HP 143.003502 (SeeEnginepages) 12 Screw 20 Pulley, V3L 22 Key, Hi Pro #505 100 Frame, Edger 300 Quill Assembly 301 Spring 302 Spring Pin 305 Belt, V4L 310 Blade Guard F=001101M KEY PARTNO. NO. DESCRIPTION PART NO. Engine 311 Bolt, C ...

  • Craftsman 536.772101 - page 22

    CRAFTSMAN 536.772101 REPAIR PARTS 418 412 416 420 405 415 403 423 343712C F_OO1101M 22 ...

  • Craftsman 536.772101 - page 23

    CRAFTSMAN 536.772101 REPAIR PARTS KEY NO. DESCRIPTION 401 Bolt, 5/16-18x.75 402 Nut, 5/16-18 403 Lower Handle 405 Handle, Depth 406 Screw 407 Spring, Compression 408 Nut, 5/16-18 409 Brkt, Adj. Quadrant 410 Rope Guide 411 Screw, 1/4-20xl.25 412 Nut, 1/4-20 415 Upper Handle 416 Bail, Operator Control 417 Torsion Spring 418 Nut, Push On 419 Cap, Oper ...

  • Craftsman 536.772101 - page 24

    CRAFTSMAN 536.772101 REPAIR PARTS 121 106 121 103 105 110 109 103 103 111 114 112 113 343716B KEY KEY NO. DESCRIPTION PARTNO. NO. DESCRIPTION 101 Rod, Axle Front 740091 109 Screw 103 Ring, Ret E. 20864 110 Flat washer 104 Arm, Front Wheel 740126-833 111 Nut, 5/16-18 105 Rod, Axle R. 740095 112 Washer, Nylon 106 Flat washer 417098 113 Spacer, Sleeve ...

  • Craftsman 536.772101 - page 25

    CRAFTSMAN 143.003502 REPAIR PARTS 130 416 1; 126 119 125 -12B 185 178 207 52 F-OO1101M 25 ...

  • Craftsman 536.772101 - page 26

    CRAFTSMAN 143.003502 KEY PART NO. NO. DESCRIPTION 0 RPM High 3050 to 3350 0 RPM Low 2400 to 2709 27625 Oil Fill Plug 29673 Oil Fill Plug Gasket 1 37289 Cylinder (Incl. 2,20 & 150) 2 26727 Dowel Pin 6 33734 Breather Element 7 36557 Breather Ass'y. (Incl. 6 & 12A) 12 36775 Breather Tube 12A 36558 Breather Cover & Tube (Incl. 12B) 12B ...

  • Craftsman 536.772101 - page 27

    CRAFTSMAN 143.003502 151 31673 Valve Spring Cap 151A 40017 Intake Valve Seal 169 36783 Valve Cover Gasket 172 36784 Valve Cover 174 30200 Screw, 10-24 x 9/16" 178 29752 Nut & Lock Washer 179 30593 Retainer Clip 182 6201 Screw, 1/4-28 x 7/8" 184 26756 Carburetor To Intake Pipe Gasket 185 36785 Intake Pipe 186 34337 Governor Link 200 33 ...

  • Craftsman 536.772101 - page 28

    CRAFTSMAN 143.003502 REPAIR PARTS (_20A 16 F-OO1101M 28 ...

  • Craftsman 536.772101 - page 29

    CRAFTSMAN 143.003502 REPAIR PARTS KEY PART N0. NO. 0 640262 1 631615 2 631767 4 631184 5 631183 6 640070 7 650506 16 631807 17 651025 18 630766 20 640018 20A 640200 25 631867 27 631024 28 632019 29 631028 30 631021 31 631022 35 640259 36 640080 36A 632766 37 632547 40 640175 44 27110A 47 630748 48 631027 60 632760B DESCRIPTION Carburetor (Incl. 184 ...

  • Craftsman 536.772101 - page 30

    CRAFTSMAN 143.003502 REPAIR PARTS ]2 _3 ]] F-001101M KEY PART NO, NO. 0 590694 1 590599A 2 590600 3 590696 4 590601 5 590697 6 590698 7 590699 8 590700 11 590695 12 590535 13 590701 8 3 DESCRIPTION Recoil Starter Spring Pin (Incl. 4) Washer Retainer Washer Brake Spring Starter Dog Dog Spring Pulley & Rewind Spring Ass'y. Starter Housing As ...

  • Craftsman 536.772101 - page 31

    For the repair or replacement parts you need delivered directly to your home Call 7am-7pm, 7days a week 1-800-366-PART (1-800-366-7278) Para ordenar piezas con entrega a domicilio - 1-800-859-7084 For in-house major brand repair service Call 24 hours a day, 7days a week 1-800-4-REPAIR (1-800-473-7247) Para pedir servicio de reparacibn a domicilio- ...

Manufacturer Craftsman Category Lawn Mower

Documents that we receive from a manufacturer of a Craftsman 536.772101 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 536.772101 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 536.772101
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 536.772101.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 536.772101, service manual, brief instructions and user manuals Craftsman 536.772101. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 536.772101.

Similar manuals

A complete manual for the device Craftsman 536.772101, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 536.772101 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 536.772101.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 536.772101 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 536.772101, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 536.772101, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 536.772101 - which should help us in our first steps of using Craftsman 536.772101
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 536.772101
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 536.772101 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 536.772101?

Use the form below

If you did not solve your problem by using a manual Craftsman 536.772101, ask a question using the form below. If a user had a similar problem with Craftsman 536.772101 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)