Manual Porter-Cable 310

17 pages 0.28 mb
Download

Go to site of 17

Summary
  • Porter-Cable 310 - page 1

    Laminate T rimmer Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Pleas ...

  • Porter-Cable 310 - page 2

    2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are ...

  • Porter-Cable 310 - page 3

    3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica from bricks and cement and other masonry pro ...

  • Porter-Cable 310 - page 4

    4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS 1) Work area safety a) Keep work a ...

  • Porter-Cable 310 - page 5

    5 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose ...

  • Porter-Cable 310 - page 6

    6 1 . Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 2. Tighten Collet nut securely to prevent the bit from slipping. Never tighten collet nut without a bit. Never adjust depth of cut while motor is running. A slip ...

  • Porter-Cable 310 - page 7

    7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litres g ........................ grams kg ........... ...

  • Porter-Cable 310 - page 8

    8 EXTENSION CORD SELECTION If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 vo ...

  • Porter-Cable 310 - page 9

    9 SELECTING THE BIT The Model 310 is equipped with a 1 / 4 " diameter collet to accept laminate trimming bits with 1 / 4 " diameter shanks. A – Motor Unit G – Ring Spring B – Base Unit H – Clamp Knob C – Sub-Base J – Collet Nut F – Depth Adjusting Ring K – Switch A F G H C B K J H C Fig. 1 FUNCTIONAL DESCRIPTION OPERA TION ...

  • Porter-Cable 310 - page 10

    10 TO INST ALL BIT 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Remove power unit from base unit as follows: a. Loosen clamping knob (H) Fig. 1. b. Grasp power unit (A) Fig. 1, and pull straight up and out of the base unit (B) Fig. 1. This will also release the depth adjusting ring (F) Fig. 1, from ring springs (G) Fig. 1. 3. Lay power unit on bench wi ...

  • Porter-Cable 310 - page 11

    11 USING A LAMINA TE TRIMMER 1. Material to be trimmed must overhang the base material by a least 1 / 8 ". 2. Always wear ansi Z87.1 safety glasses while operating a laminate trimmer. 3. DISCONNECT TOOL FROM POWER SOURCE. 4. Firmly grasp motor housing being sure switch is in the “OFF” position. 5. Verify bit is clear of foreign objects and ...

  • Porter-Cable 310 - page 12

    12 ASSEMBLING AND ADJUSTING BASE AND ROLLER (73100) 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Remove power unit from base unit (see TO INSTALL BIT), and install the bit. 3. Position the base and roller guide assembly (A) Fig. 2, to the base unit. The alignment pin on the back of the guide base fits into hole (C) Fig. 3. 4. Place the two mounting scr ...

  • Porter-Cable 310 - page 13

    13 FLUSH TRIMMING 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Attach base and guide to trimmer as outlined under ASSEMBLING AND ADJUSTING BASE AND ROLLER. 3. Remove roller guide and replace with flush trimming guide (B) Fig. 2. This guide may be identified by the molded on letter “F”. The stud on the end of this guide must face toward the trimmer ...

  • Porter-Cable 310 - page 14

    14 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air. F AILURE TO ST AR T Should your tool fail ...

  • Porter-Cable 310 - page 15

    15 A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. Since accessories other than those offered by Porter-Cable • ...

  • Porter-Cable 310 - page 16

    16 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material du ...

  • Porter-Cable 310 - page 17

    The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...

Manufacturer Porter-Cable Category Laminate Trimmer

Documents that we receive from a manufacturer of a Porter-Cable 310 can be divided into several groups. They are, among others:
- Porter-Cable technical drawings
- 310 manuals
- Porter-Cable product data sheets
- information booklets
- or energy labels Porter-Cable 310
All of them are important, but the most important information from the point of view of use of the device are in the user manual Porter-Cable 310.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Porter-Cable 310, service manual, brief instructions and user manuals Porter-Cable 310. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Porter-Cable 310.

Similar manuals

A complete manual for the device Porter-Cable 310, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Porter-Cable 310 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Porter-Cable 310.

A complete Porter-Cable manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Porter-Cable 310 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Porter-Cable 310, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Porter-Cable 310, that we can find in the current document
3. Tips how to use the basic functions of the device Porter-Cable 310 - which should help us in our first steps of using Porter-Cable 310
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Porter-Cable 310
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Porter-Cable 310 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Porter-Cable 310?

Use the form below

If you did not solve your problem by using a manual Porter-Cable 310, ask a question using the form below. If a user had a similar problem with Porter-Cable 310 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)