Manual Sears 26462_0

22 pages 1.93 mb
Download

Go to site of 22

Summary
  • Sears 26462_0 - page 1

    SF./_S OWNERS MANUAL Model No. 26462_0 CRAFTSMAN o PROFESSIONAL MID-SIZED ROUTER TABLE WARNING: Before operating product, read this manual and follow all its Safety and Operating Instructions. Sears, Roebuck and Co., Hoffman Estates IL 60179 USA 26462 12/00 Printed in U.S.A. 4 9LCN- 84 ...

  • Sears 26462_0 - page 2

    General Safety Instructions for Power Tools ................................................ 3 Additional Safety Instructions for Router Tables ......................................... 4 Introduction ........................................ . ......................................................... '...5 Optional Router Table Accessories ... ...

  • Sears 26462_0 - page 3

    SAFETY GUIDELINES- DEFINITIONS This manual contains informa- tion that is important for you to know and understand. This information relates to protect- ing YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you rec- ognize this information, we use the symbols to the right. Please read the manual and pay attention to these sections. IADANGER l ...

  • Sears 26462_0 - page 4

    18. Use recommended accessories Consult the owner's manual for recommended accessories and follow the instructions. The use of improper accessories may cause hazards. 19. Never stand on tool Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. DO NOT store materials above or near the tool making it ...

  • Sears 26462_0 - page 5

    switch box when turning the router ONor OFF. DO NOT touch anything but the switch box when doing this. NEVER reach under the router table for anyrea- son when therouter is running, except to turn it OFF. I A I 24.[ WARNING J Before making any cut, make sure the router is turned OFF, the router bit is not rotating, and the power cord is unplugged fr ...

  • Sears 26462_0 - page 6

    TOOLS REQUIRED • Phillips screwdriver. ° Small or medium sized adjustable wrench (or a set of nutdrivers). ° Electrical with 5/32" drill bit. • Hammer ROUTER TABLE 1. Position the router table top (Part No. 29LCN-981) as shown in Figure 1, with the bottom of the table top facing toward you. 2. Position the table legs (Part No. 29LCN-1283 ...

  • Sears 26462_0 - page 7

    FIGURE 5 FIGURE 7 Front of--. Router Table #10-32 Hex "Keps"_ Nut, (Typical)_ -_,- _ / Router _ _ ,_/ / Table _,_ _ --///_ / Leg Switch_ "_ #10-32 518" Long Truss Head Machin Screw, (Typical) MOUNTING ROUTER TO THE ROUTER TABLE I WARNINGI ALWAYS UNPLUG ROUTER BEFORE MOUNTING. Craftsman Routers with Three-Hole and 6" Diame ...

  • Sears 26462_0 - page 8

    Other Brands of Routers It will be necessary for you to purchase a Craftsman Professional Router Adapter Plate, #25333, from your local Sears Retail Outlet, or through the Sears Catalogue. Routers with a total overall height of 13 inches or less, and a base diameter of 7 inches or less can be accommodated. m I NOTE I Because of vibration that occur ...

  • Sears 26462_0 - page 9

    4. Repeat steps 1 through 3 for the other side of the fence. 5. Make sure the adjustable jointing fence is inside the router table fence as far as it will go and that the clamping knob has been securely tightened. FIGURE 14 Fence Clamping Knob 114-20 x 1-3/4",ong II Round Head _./|l Square IL Neck Bolt / 9/32" LD. x 3/4" O.D. L_ / x ...

  • Sears 26462_0 - page 10

    I _'WARNINGI The vibrations from operating the router can, from time to time, cause the hex nut and the clamp plate to become loose on the clamp rod. PERIODICALLY CHECK THESE FASTENERS AND ALL FASTENERS to ensure that they are tight and secure. PUSH BLOCK ASSEMBLY TO THE ROUTER TABLE FENCE 1. Position the clamp plate relative to the push block ...

  • Sears 26462_0 - page 11

    surface before use. Failure to do so could cause the router table to tip over or slide, resulting in property damage and/or serious personal injury. 1. Set the router table on a workbench or other stable and sturdy surface. 2, While holding the router table in place, spot the loca- tion of the two mounting holes in each of the legs onto the workben ...

  • Sears 26462_0 - page 12

    GENERAL The power switch box is designed to be used with most Craftsman router tables. It provides the conven- ience of an "ON-OFF" switch box at the front of the table, thus eliminating the need to reach underneath the table to turn the router "ON" and "OFF". The power switch box also provides an optional simultaneous ...

  • Sears 26462_0 - page 13

    The switch box incorporates two positive features to prevent inadvertent switching on of the router and the unauthorized, and possibly hazardous, use by others. Inadvertent switching on of the router is prevented by the clear plastic switch box cover. The cover must be raised and the switch box manually toggled to the "ON" position to sta ...

  • Sears 26462_0 - page 14

    USING THE ROUTER TABLE The fence on your router table is provided as a guide to hold the work piece for accuracy in routing. I_I_WARNING] BEFORE each and every use, make sure the router table is SECURE on a work- bench and DOES NOT MOVE. ALIGNMENT OF UNITIZED FENCE TO MITER BAR SLOT 1. Line up the front of the fence with the "0" marks on ...

  • Sears 26462_0 - page 15

    section ADJUSTING DEPTH AND HEIGHT OFTHE CUT. Tightly secure the fence assembly and the router as described before. (MAKE SURE ROUTER IS UNPLUGGED WHEN MAKING ADJUSTMENTS.) 3. LOWER THE OVERHEAD GUARD to the operating position. (Overhead guard shown raised for reasons of clarity.) 4. Check you adjustments by turning the router "ON" using ...

  • Sears 26462_0 - page 16

    FIGURE 29 Fence Clamping Knob Fence Clamping Knob Fence.,. Clamping_ Knob', _crap Nood Adjustabk Jointing Fence flush with Router Table ' Piloted Router Bit Fence Overhead guard shown raised for reasons of clarity. FIGURE 30 Router Table Fence Work Piece Pilot Bearing rides against Router Pilot Bearing Piloted Router Bit "Work Piece ...

  • Sears 26462_0 - page 17

    Cutting Tenons 1. Make certain that the adjustable fence is locked in position with its face flush with the front face of the fence. 2. Mount the push block assembly on the fence, as described in the section PUSH BLOCK ASSEMBLY TO THE ROUTER TABLE UNITIZED FENCE. 3. Install the proper table top insert into the table top hole. 4. Mark line "A&q ...

  • Sears 26462_0 - page 18

    I I When cutting tenons, always clamp I NOTE the work piece with the end to be cut resting flat on the table top. This will minimize steps in the finished tenon surface due to variations in the table top flatness. See FIGURE 36 k Piece ////_ _" Previous cuts Figure 37. l I NOTE I Always cut full depth on all four J sides of tenon in one pass a ...

  • Sears 26462_0 - page 19

    PARTS LIST FOR CRAFTSMAN PROFESSIONAL MID-SIZED ROUTER TABLE MODEL NO. 26462 @ @ @ @ @@@ @ @ @@ @@@ @ @@ KEY! 1 2 '3 4 5 6 7 .-. 8 9 10 "-11 - "12 "13 _14 15 _16 17 _'- 18 _19 -"'- 20 PART NO. 29LCN-981 29LCN-1283 29LCN-996-1 29LCN-996-2 29LCN-996-3 29LCN-1255 29LCN-1019 29LCN-1018 29LCN-994 29LCN-758 29LCN-99 ...

  • Sears 26462_0 - page 20

    TABLE ASSEMBLY FENCE ASSEMBLY U MISCELLANEOUS PARTS 2O ...

  • Sears 26462_0 - page 21

    MITER BAR ASSEMBLY @ PUSH BLOCK ASSEMBLY SWITCH ASSEMBLY 21 ...

  • Sears 26462_0 - page 22

    When corresponding, always give the following information as shown in the list: Printed in U.S.A. 12/00 49LCN-84 1. The PART NUMBER 2. The PART DESCRIPTION 3. The MODEL NUMBER: 26462 4. The ITEM NAME - PROFESSIONAL MID-SIZED ROUTER TABLE ...

Manufacturer Sears Category Router

Documents that we receive from a manufacturer of a Sears 26462_0 can be divided into several groups. They are, among others:
- Sears technical drawings
- 26462_0 manuals
- Sears product data sheets
- information booklets
- or energy labels Sears 26462_0
All of them are important, but the most important information from the point of view of use of the device are in the user manual Sears 26462_0.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Sears 26462_0, service manual, brief instructions and user manuals Sears 26462_0. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Sears 26462_0.

Similar manuals

A complete manual for the device Sears 26462_0, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Sears 26462_0 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Sears 26462_0.

A complete Sears manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Sears 26462_0 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Sears 26462_0, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Sears 26462_0, that we can find in the current document
3. Tips how to use the basic functions of the device Sears 26462_0 - which should help us in our first steps of using Sears 26462_0
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Sears 26462_0
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Sears 26462_0 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Sears 26462_0?

Use the form below

If you did not solve your problem by using a manual Sears 26462_0, ask a question using the form below. If a user had a similar problem with Sears 26462_0 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)