English dropdown-ico

Manual TRENDnet TC-NT2

8 pages 0.57 mb
Download

Go to site of 8

Summary
  • TRENDnet TC-NT2 - page 1

    TC-NT2 TC-NT2 PROFESSIONAL NETWORK TESTER INSTRUCTION MANUAL ...

  • TRENDnet TC-NT2 - page 2

    The Network Cable T ester comes in two modular units, a master unit and a remote terminator . The modular design enables the tester to be used for local loop-back test of a patch cable or remote testing of pre-installed premise wiring. The Network Cable T ester verifies continuity of individual wires and identifies open, shorted and cross-connected ...

  • TRENDnet TC-NT2 - page 3

    FEA TURES: 1. T ests pin to pin connection of cables. 2. For loop-back and remote testing. 3. Auto - scan and manual step testing. 4. Checks for opens shorts and cross connected wires. 5. T ests Lan, T elcom, UTP/STP and coax BNC cables. 6. T one feature easily locates remote cable ends. CAUTION: NOT FOR USE ON LIVE CIRCUITS. DOING SO WHERE VOL T A ...

  • TRENDnet TC-NT2 - page 4

    into the respective jacks (TX, RX) on the master unit. 2. Set the power switch to ON. (a) Auto Scan Mode: Press and release the AUTO button, the LED in the TX row will scroll in sequence (1,2,..., shield and repeat), to indicate the pins being tested. The RX row of LED will light (or not), in relation to the TX row , to indicate status. (b) Manual ...

  • TRENDnet TC-NT2 - page 5

    straight, reverse, miss-wire...etc.) can be determined. i) If more than one LED from the same row is lit or if TX & RX LEDs are unlit simultaneously- This indicates a short . ii) If a LED is skipped - This may indicate an open or a burnt out LED. iii) If no LED will light - please check or replace your battery . 3. T o test BNC, USB or other ca ...

  • TRENDnet TC-NT2 - page 6

    B. REMOTE TEST 1. Connect one end of the test cable to the MASTER unit marked TX . 2. Set the power switch to ON and set the tester to Auto scan. The TX LED will begin to scroll in sequence (1,2,3,..., shield and repeat), to indicate the pins being tested. Use a patch cord (included) if the test cable terminates into a wall jack or patch panel. 3. ...

  • TRENDnet TC-NT2 - page 7

    cable 1. Set the power switch to ON/TONE and by pressing the TEST button to select a pin to carry a tone or set the tester to AUTO scan, a sequencing tone is supplied on each of the 8 pins, shield and BNC cable. Or set the main unit on shield position. 2. The tone signal can then be received by the Net Probe (PR- 06P) or any tone probe for tracing ...

  • TRENDnet TC-NT2 - page 8

    3. RJ45 to RJ45 patch cord. 4. Carrying pouch. 5. User guide. E. REMARKS 1. The Master tester runs on one 9V standard or alkaline battery . 2. Please make sure the battery is fresh and have sufficient power . If a battery is weak or fails, the LED indicators will be dim or fail to light. The tester may not scan. 3. Please take out the battery if yo ...

Manufacturer TRENDnet Category Security Camera

Documents that we receive from a manufacturer of a TRENDnet TC-NT2 can be divided into several groups. They are, among others:
- TRENDnet technical drawings
- TC-NT2 manuals
- TRENDnet product data sheets
- information booklets
- or energy labels TRENDnet TC-NT2
All of them are important, but the most important information from the point of view of use of the device are in the user manual TRENDnet TC-NT2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals TRENDnet TC-NT2, service manual, brief instructions and user manuals TRENDnet TC-NT2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product TRENDnet TC-NT2.

Similar manuals

A complete manual for the device TRENDnet TC-NT2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use TRENDnet TC-NT2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of TRENDnet TC-NT2.

A complete TRENDnet manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual TRENDnet TC-NT2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the TRENDnet TC-NT2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the TRENDnet TC-NT2, that we can find in the current document
3. Tips how to use the basic functions of the device TRENDnet TC-NT2 - which should help us in our first steps of using TRENDnet TC-NT2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with TRENDnet TC-NT2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of TRENDnet TC-NT2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning TRENDnet TC-NT2?

Use the form below

If you did not solve your problem by using a manual TRENDnet TC-NT2, ask a question using the form below. If a user had a similar problem with TRENDnet TC-NT2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)