English dropdown-ico

Manual Hitachi 21

22 pages 0.22 mb
Download

Go to site of 22

Summary
  • Hitachi 21 - page 1

    Please read this operation Guide carefully for proper operation, and keep it for future refernce. B E-IR20 / 21 Infrared B/W Camera Module Operation Guide ...

  • Hitachi 21 - page 2

    Table of Contents BE-I R20 / 21 1 1. Intr oduction ･･･････････････････････････････････････････   2 2. General ･･･････････････････････････････････････････････   2 3. C ...

  • Hitachi 21 - page 3

    1. Introducti on BE-I R20 / 21 2 Thank you v ery much for your purchase of the Hitachi BE-IR20/21 Black and W hite Camera Module. Prior to using this camera , read this manual carefully. 2 . G e n e r a l The Hitachi BE-IR20/ 21 ar e black and whit e camer a modules using a 1/ 4 inch interline CCD. The BE-IR20/21 are so small that they are most sui ...

  • Hitachi 21 - page 4

    4 ． ． ． ． Specif ications BE-I R20 / 21 3 8) External sync input HD & VD : 5V peak -to-peak negative Input impedance : 1k Ω Frequency dev iat ion : ± 1% 9) Video output 1.0 Vp-p, 75 Ω , unbalanced Video component : 0.7 Vp-p Sync component : 0.3 Vp-p negative 10) Resolution EIA : 570(H) × 380(V) TV lines CCIR : 560(H) × 380(V) TV ...

  • Hitachi 21 - page 5

    5. Notes to users BE-I R20 / 21 4  Power supply z Connect a 9V DC volt age (8. 5 t o 9. 5V) from an external regulat ed DC pow er supply . z Use a stable power supply w it hout ripple and noise. z Prior to turning on the power swit ch , check that the polarities of the power cable are correct , referring to the connection diagram (Page 8 , 9) ? ...

  • Hitachi 21 - page 6

    5. Notes to users BE-I R20 / 21 5  Phenomena inherent to CCD imaging dev ice Following are phenomena inherent t o a CCD imaging dev ice , and not defect s. z Smear and blooming W hen strong light (lamp , fluorescent lamp , refl ected light , etc.) is shot , pale bands are displayed v ert ically above and below t he light. In this case , change t ...

  • Hitachi 21 - page 7

    6. External view BE-I R20 / 21 6 Dimensions 7. Optical dimensions Lens 19.2 ± 0.5 (C-mount) 1.4 ± 0.2 CCD Base plate Imaging face Lens-mount Extension of optical path due to the thicknes s of CCD glas s is considered. ...

  • Hitachi 21 - page 8

    8. Installation BE-I R20 / 21 7 W hen installing the camera in a housing or unit of equipment, secure with t wo M2 screws inserted into the 2. 5 mm diameters holes of the SENS board base plate. 1. Use the SENS board holds to install the camera. Avoid using only the Main board, due to risk of damage to the board connector. 2. Avoid unnecessary stres ...

  • Hitachi 21 - page 9

    9. Typical connection BE-I R20 / 21 8 BE-IR20 Image processor or Video monitor Regulated power supply (More then 300 mA) Note1 : • When more than one video monitor is connected in series , set the 75 Ω termination sw itch on the last unit to ON. Note2 : • Supply voltage range : 8.5 to 9.5V • Be sure to check the polarities of the pow er sou ...

  • Hitachi 21 - page 10

    9. Typical connection BE-I R20 / 21 9 BE-IR21 Image processor or Video monitor Regulated power supply (More then 300 mA) Note1 : • When more than one video monitor is connected in series , set the 75 Ω termination sw itch on the last unit to ON. Note2 : • Supply voltage range : 8.5 to 9.5V • Be sure to check the polarities of the pow er sou ...

  • Hitachi 21 - page 11

    10. External sync (BE-IR21) BE-I R20 / 21 10 Supply sync signals (HD and VD) f or BE-IR21 operation. Refer to connec tion on page 9. z Horizontal and vertical drive signal inputs HD EIA: f(H) = 15.734 k Hz ± 1 % VD EIA: f(V) = 59.94 Hz (f( V) = f(H) ÷ 262.5) z Input level HD 4 to 6 Vp-p negative VD 4 to 6 Vp-p negative z Input im pedance 1 k Ω H ...

  • Hitachi 21 - page 12

    11. Function setting and changes BE-I R20 / 21 11 W hen changing the function settings , perform the work with thorough care. Be sure to use anti-static measures such as a grounding band. Also observe safety precautions when soldering to avoid burn and fire hazards. Hitachi Denshi assumes on liability for damage or injury resulting fr om such w ork ...

  • Hitachi 21 - page 13

    11. Function setting and changes BE-I R20 / 21 12 11-2 Gamma response The factory setting is gamma on. If necessary , the gamma response can be changed as follows. Change the gamma response by changing the chip part. Gamma ( γ )response R217 R218 R219 ON Absent 0 Ω 0 Ω Factory sett ing OFF 0 Ω Remove Remove 0 Ω : Part code RME1784 Descript ...

  • Hitachi 21 - page 14

    11. Function setting and changes BE-I R20 / 21 13 11-3 Auto electronic shutter on / off Factory sett ing for auto elect ronic shut t er is off. If necessary , it can be set t o on. Absent the R259 , R260 chip t o set t he aut o elect r onic shut t er to on. Auto electronic s hutter R259 R260 OFF 0 Ω 0 Ω Factory setting ON Absent Absent 0 Ω : ...

  • Hitachi 21 - page 15

    11. Function setting and changes BE-I R20 / 21 14 11-4 Changes to fixed shutter mode The fixed shutter mode can be changed by replacing the chip parts indicat ed below . Mode R259 R260 R261 R262 R263 R264 R265 R266 R267 R268 R269 Normal mode 0 Ω 0 Ω Absent 0 Ω A bsent 6800 10k 27k 10k 10k 27k Auto elec t ronic shutt er m ode Remove Rem ove Ab ...

  • Hitachi 21 - page 16

    11. Function setting and changes BE-I R20 / 21 15 11-5 BE-IR20 external sync The BE-IR20 factory sett ing is for internal sync. If required, this can be changed to external sync by changing chip part s. Change the following chip parts for external sync operat ion. Sy nc system R280 R281 R282 R284 Internal 100 Ω Absent Absent 0 Ω Factory setti n ...

  • Hitachi 21 - page 17

    11. Function setting and changes BE-I R20 / 21 16 11-6 BE-IR21 internal sync The BE-IR21 factory sett ing is for external sync. If required, this can be changed to internal sync by changing chip part s. Change the following chip parts for internal sy nc operat ion. Sy nc system R280 R281 R282 R284 External Absent 0 Ω 100 Ω Absent Factory settin ...

  • Hitachi 21 - page 18

    11. Function setting and changes BE-I R20 / 21 17 11-7 HD and VD output (BE-IR20 only) The BE-IR20 can be provided with horizontal and vert ical drive outputs by changing chip parts. Change the following chip parts to prov ide HD and VD outputs. R233 R239 R240 R241 R242 R248 R249 R250 Factory sett ing 0 Ω Absent 0 Ω Absent 0 Ω Absent 0 Ω Ab ...

  • Hitachi 21 - page 19

    12. Opt ions BE-I R20 / 21 18 LA-IR20 Mount adapter dimensions Remove c-mount attachment to use as cs-mount. ...

  • Hitachi 21 - page 20

    12. Options BE-I R20 / 21 19 BE-IR20/21 and LA-IR 20 combined dimensions ...

  • Hitachi 21 - page 21

    BE-I R20 / 21 20 Spectral sensitivity (t ypical example) 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 400 500 600 700 800 900 1000 Relative sensitivity W avelength( nm) ...

  • Hitachi 21 - page 22

    BE-I R20 / 21 21 Caution The s pecifications of this equipm ent are subj ect to change without notice for im provem ent. Prior to placing your order , be sur e to confirm that these spec ifications are the latest ones. Hitachi Denshi guarantee that the equipment s hipped from our factor y conf orm s to the Hitachi Denshi’s st andard warranty cond ...

Manufacturer Hitachi Category Digital Camera

Documents that we receive from a manufacturer of a Hitachi 21 can be divided into several groups. They are, among others:
- Hitachi technical drawings
- 21 manuals
- Hitachi product data sheets
- information booklets
- or energy labels Hitachi 21
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hitachi 21.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hitachi 21, service manual, brief instructions and user manuals Hitachi 21. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hitachi 21.

Similar manuals

A complete manual for the device Hitachi 21, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hitachi 21 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hitachi 21.

A complete Hitachi manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hitachi 21 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hitachi 21, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hitachi 21, that we can find in the current document
3. Tips how to use the basic functions of the device Hitachi 21 - which should help us in our first steps of using Hitachi 21
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hitachi 21
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hitachi 21 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hitachi 21?

Use the form below

If you did not solve your problem by using a manual Hitachi 21, ask a question using the form below. If a user had a similar problem with Hitachi 21 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)