Manual Apple 073-0841

16 pages 0.63 mb
Download

Go to site of 16

Summary
  • Apple 073-0841 - page 1

    073-0841 Re v . A  Power Mac G4 Cube Optical Drive Replacement Instructions F ollow the instructions in this sheet carefully . F ailure to f ollo w these instructions could damage your equipment and v oid its w arranty . Note: Written and video instructions covering customer-installab le par ts are av ailab le at http://www .info .apple.com/inst ...

  • Apple 073-0841 - page 2

    Power Mac G4 Cube Optical Drive - 2 Removing the Computer Cor e Fr om the Enclosur e W arning: Always shut do wn y our computer before opening it to a v oid damaging its internal components or causing injury . After y ou shut down the computer , the internal components can be very hot. Let the computer cool down bef ore continuing. 1 Place your com ...

  • Apple 073-0841 - page 3

    Power Mac G4 Cube Optical Drive - 3 6 T ur n the computer upside down, and push do wn on the latch to release it. Allow the latch to extend completely. (Figure 2) Figure 2 7 Gently pull the core from the computer enclosure and place the core on a soft cloth. (Figure 3) Figure 3 Latch Extended Latch Core Enclosure ...

  • Apple 073-0841 - page 4

    Power Mac G4 Cube Optical Drive - 4 Removing the T op Plate Assembly 1. Press the latch in, and tur n o v er the core so the pow er button f aces up. 2. Remov e the f our corner screws that secure the top plate to the f our v er tical posts . 3. Remov e the f our scre ws on the two sides . (The two scre ws that align with the vertical plates are mu ...

  • Apple 073-0841 - page 5

    Power Mac G4 Cube Optical Drive - 5 4. Lift out the LED cov er that is fitted o v er the power b utton LED . Set the LED co v er aside f or installation on the top plate assembly . (Figure 5) Figure 5 5. Carefully lift up the top plate and disconnect the ke y ed connector (J1 on the logic board). (Figure 6) Figure 6 ...

  • Apple 073-0841 - page 6

    Power Mac G4 Cube Optical Drive - 6 Removing the Installed Optical Dri ve Note: The procedure is the same whether the optical dr iv e is a CD-R W or a D VD-ROM drive. 1. Grasp the top of the side panel, and slide it up and a wa y to clear the four tabs on the inner side of the panel. (Figure 7) Figure 7 2. Mov e the AirP or t Card antenna cable out ...

  • Apple 073-0841 - page 7

    Power Mac G4 Cube Optical Drive - 7 3. Using a magnetized scre wdriver , remov e the two scre ws from the side of the drive . Repeat on the other side. (Figure 9) Figure 9 ...

  • Apple 073-0841 - page 8

    Power Mac G4 Cube Optical Drive - 8 4. W arning: If the optical drive case is squeezed too tightly, the laser lens could be damaged. When handling the drive case, touch only the outer edges of the case. Holding the drive case by the corner, pull the drive up about half way and disconnect the ATA ribbon cable. Then, using pliers, grasp the power cab ...

  • Apple 073-0841 - page 9

    Power Mac G4 Cube Optical Drive - 9 6. Disconnect the board from the drive b y removing the tw o screws . Then pull the board off of the drive . (Figure 11) W arning: If the optical drive case is squeezed too tightly, the laser lens could be damaged. When handling the drive case, touch only the outer edges of the case. Figure 11 Installing the Repl ...

  • Apple 073-0841 - page 10

    Power Mac G4 Cube Optical Drive - 10 2. Install the connector board on the replacement optical drive , and secure it to the drive with the two scre ws. (Figure 13) Figure 13 3. Holding the optical drive case b y one corner , position the drive o ver the chassis so the labeled panel f aces out and the connector board is at the bottom of the drive ca ...

  • Apple 073-0841 - page 11

    Power Mac G4 Cube Optical Drive - 11 5. Install the screws , b ut do not tighten until all f our are in place. Do not overtighten. 6. Close the AirP or t Card door and secure the antenna cable (and AirP or t Card). 7. Star ting with the two bottom tabs, attach the side panel as sho wn. Ensure all four tabs engage and no cables get caught. (Figure 1 ...

  • Apple 073-0841 - page 12

    Power Mac G4 Cube Optical Drive - 12 Replacing the T op Plate Assembly 1. With the top plate assembly in hand, connect the cab le from the top plate to the J1 connector on the logic board. (Figure 17) W arning: To prevent damage to the power board, ensure the keyed connector fits into the J1 connector as shown. Figure 17 ...

  • Apple 073-0841 - page 13

    Power Mac G4 Cube Optical Drive - 13 2. Install the LED cov er o v er the power b utton LED on the top plate assemb ly . 3. P osition the top plate assembly ov er the core . Ensure that the four metal tabs align with the f our slots in the top plate, and the D VD-ROM panel tucks in under the lip of the top plate. (Figure 18) Figure 18 4. Star ting ...

  • Apple 073-0841 - page 14

    Power Mac G4 Cube Optical Drive - 14 Replacing the Computer Cor e in the Enclosure 1. Make sure that the po wer b utton gask et is secured inside the recessed area of the computer enclosure. (Figure 19) Figure 19 Caution: If the power button gasket is not centered correctly in the shell, the computer might not power up. Make sure the power button g ...

  • Apple 073-0841 - page 15

    Power Mac G4 Cube Optical Drive - 15 2 Holding the core by the latch, insert the core into the enclosure. (Figure 20) Note: The core fits into the enclosure only one way. Position the core so the ports are toward the back of the enclosure. Figure 20 3 With a flat hand, press down on the latch until it loc ks into place . Firmly press the core to e ...

  • Apple 073-0841 - page 16

    Power Mac G4 Cube Optical Drive - 16 4 T ur n y our computer upright and reconnect all cables. 5 Restar t your computer . W arning: Never turn on your computer unless all of its internal and e xternal parts are in place and it is closed. Operating the computer when it is open or missing parts can damage your computer or cause injury .  Apple Com ...

Manufacturer Apple Category Personal Computer

Documents that we receive from a manufacturer of a Apple 073-0841 can be divided into several groups. They are, among others:
- Apple technical drawings
- 073-0841 manuals
- Apple product data sheets
- information booklets
- or energy labels Apple 073-0841
All of them are important, but the most important information from the point of view of use of the device are in the user manual Apple 073-0841.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Apple 073-0841, service manual, brief instructions and user manuals Apple 073-0841. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Apple 073-0841.

Similar manuals

A complete manual for the device Apple 073-0841, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Apple 073-0841 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Apple 073-0841.

A complete Apple manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Apple 073-0841 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Apple 073-0841, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Apple 073-0841, that we can find in the current document
3. Tips how to use the basic functions of the device Apple 073-0841 - which should help us in our first steps of using Apple 073-0841
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Apple 073-0841
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Apple 073-0841 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Apple 073-0841?

Use the form below

If you did not solve your problem by using a manual Apple 073-0841, ask a question using the form below. If a user had a similar problem with Apple 073-0841 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)