English dropdown-ico

Manual Skil 3100

11 pages 1.63 mb
Download

Go to site of 11

Summary
  • Skil 3100 - page 1

    For English V ersion V ersion française V ersión en español See page 2 V oir page 12 V er la página 12 Operating/Safety Instructions Consignes de fonctionnement/sécurité Instrucciones de funcionamiento y seguridad IMPOR T ANT : IMPOR T ANT : IMPOR T ANTE: Read Before Using Lire avant usage Leer antes de usar 1-877-SKIL999 (1-877-754-5999) www ...

  • Skil 3100 - page 2

    2. General Safety Rules “ READ ALL INSTRUCTIONS” Failure to follow the safety rules listed below and other basic safety precautions may result in serious personal injury. THINK SAFETY Safety is a combination of operator common sense and alertness at all times when the X-Bench is being used. W ork Area KEEP CHILDREN AWAY Do not let visitors cont ...

  • Skil 3100 - page 3

    3. Read and understand all instructions for use of X- Bench and insert plates with tools. Failure to follow all instructions listed below may result in serious personal injury. Use only with Skil accessory insert plates (jig saw, drill press, belt sander and router). The stamped rails or clamps may have sharp edges. Be careful in handling the bench ...

  • Skil 3100 - page 4

    Replace damaged cords immediately. Use of damaged cords can shock, burn or electrocute. Always use proper extension cord. If an extension cord is necessary, a cord with adequate size conductors should be used to prevent excessive voltage drop, loss of power or over- heating. The table shows the correct size to use, de- pending on cord length and na ...

  • Skil 3100 - page 5

    5. 1. Opening the X-Bench a . T he X-Bench comes in the folded position and no assembly is r equired. In order to open the X-Bench, the user must pull and twist the main knob, located by the handle, to the open position (Fig. 1a). b. After the table has been opened, the knob must be turned back into the locked position before extending the legs or ...

  • Skil 3100 - page 6

    c. Once the user sets one leg at the desired height, follow the same steps for the remaining three legs. 4. Adjustable Foot – for Leveling Bench a. If you are working in an area that is not level, we have provided a solution. We have an adjustable foot that will extend 1.75” inches to level your bench (Fig. 6). Before operating make sure the en ...

  • Skil 3100 - page 7

    7 . M ake sure X-Bench is not plugged in and m ain outlet is off. 8. Power Switch a. The female plug is located on the bottom of the switch and the m ale plug is located on the side of the switch box (Fig. 11). C onnect the switch box to an electrical outlet by using an e xtension cord. Plug the desired tool into the female plug and turn the switch ...

  • Skil 3100 - page 8

    11. Tail Vise (Sold Separately) a. Locate the following parts: (1) Clamp block (MDF), (2) Guide rods, (1) Threaded rod, (6) Bolts and (6) Bolt covers. b. Position clamp block (MDF) over guide rods, and threaded r od as shown in figure 16 c . Securely attach guide block to the rods with (6) washer and bolts provided (Fig. 16). d . Place one bolt cov ...

  • Skil 3100 - page 9

    15. Shelf and Tool Bag (Sold Separately) a. Shelf and tool bag come fully assembled. b. There are four hooks under the work bench (Fig. 23.) c. Attach the Velcro straps located on the shelf to the hooks under the table (Fig. 23). Note: Unit can fold up with shelf and bag attached. Maximum weight load is 20lbs. 13. Finishing Tray (Sold Separately) a ...

  • Skil 3100 - page 10

    10 . 15. Universal Insert Plate: a. A blank insert plate is provided with the X-Bench. This area is meant to be used only with the Skil insert plate technology which is sold separately. The insert plates which can be purchased separately are a jigsaw insert plate, sander insert plate, router insert plate and a drill press insert plate. Use only X-B ...

  • Skil 3100 - page 11

    11 . Direction of Cut Direction of Cut ...

Manufacturer Skil Category Saw

Documents that we receive from a manufacturer of a Skil 3100 can be divided into several groups. They are, among others:
- Skil technical drawings
- 3100 manuals
- Skil product data sheets
- information booklets
- or energy labels Skil 3100
All of them are important, but the most important information from the point of view of use of the device are in the user manual Skil 3100.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Skil 3100, service manual, brief instructions and user manuals Skil 3100. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Skil 3100.

Similar manuals

A complete manual for the device Skil 3100, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Skil 3100 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Skil 3100.

A complete Skil manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Skil 3100 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Skil 3100, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Skil 3100, that we can find in the current document
3. Tips how to use the basic functions of the device Skil 3100 - which should help us in our first steps of using Skil 3100
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Skil 3100
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Skil 3100 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Skil 3100?

Use the form below

If you did not solve your problem by using a manual Skil 3100, ask a question using the form below. If a user had a similar problem with Skil 3100 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)