English dropdown-ico

Manual Barco DATA 708

34 pages 0.85 mb
Download

Go to site of 34

Summary
  • Barco DATA 708 - page 1

    R9002129 INST ALLA TION MANUAL DA T A 708 ...

  • Barco DATA 708 - page 2

    ...

  • Barco DATA 708 - page 3

    BARCO PROJECTION SYSTEMS Date : 260597 Art. No. : R5975987A R9002129 INST ALLA TION MANUAL DA T A 708 ...

  • Barco DATA 708 - page 4

    Due to constant research, the information in this manual is subject to change without notice. Produced by BARCO NV, May 1997. All rights reserved. Trademarks are the rights of their respective owners. BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Printed in Belgium ...

  • Barco DATA 708 - page 5

    Table of Contents i-1 5975987A BARCODATA 708 260597 T ABLE OF CONTENTS i WARNINGS .................................................................................................................................................................................... 1 -1 SAFETY INSTRUCTIONS .............................................................. ...

  • Barco DATA 708 - page 6

    Table of Contents i-2 5975987A BARCODATA 708 260597 ...

  • Barco DATA 708 - page 7

    Safety Instructions 1-1 5975987A BARCODATA 708 260597 WARNING TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT) This equipment has been tested and found to comply with the limits of a class A digital device, pursuant to Part 15 of the FCC Rules. These limits ...

  • Barco DATA 708 - page 8

    Safety Instructions 1-2 5975987A BARCODATA 708 260597 Power cord with ANSI 73.11 plug : The wires of the power cord are colored in accordance with the following code. Green/yellow: ground White: neutral Black: line (live) 3 . Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconne ...

  • Barco DATA 708 - page 9

    Unpacking and Dimensions 2-1 5975987A BARCODATA 708 260597 2 UNP ACKING AND DIMENSIONS Unpacking Take the projector out of its shipping carton and place it on a table. Save the original shipping carton and packing material, they will come in handy if you ever have to ship your projector. For maximum protection, repack your projector as it was origi ...

  • Barco DATA 708 - page 10

    Unpacking and Dimensions 2-2 5975987A BARCODATA 708 260597 Projector dimensions (mm) ...

  • Barco DATA 708 - page 11

    Installation Guidelines 3-1 5975987A BARCODATA 708 260597 3 INST ALLA TION GUIDELINES Installation guidelines Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system. * Environment Do not install the projection system in a site ne ...

  • Barco DATA 708 - page 12

    Installation Guidelines 3-2 5975987A BARCODATA 708 260597 * Where to install the projector? To indicate a correct installation position it is necessary to know the distance : - projector - ceiling - projector - screen To find this correct position for the projector, equipped with HD145 lenses, formulas are given in the next paragraph. Abbreviations ...

  • Barco DATA 708 - page 13

    Installation Set Up 1-1 5975987A BARCODATA 708 260597 4 INST ALLA TION SET UP Access to controls Opening procedure : During the projector set up and installation it is neces- sary to open the top cover. To gain access, procede as follow : *Turn both lock screws with a screwdriver or a coin counter clockwise. * Lift up and pivot the top cover. * Sup ...

  • Barco DATA 708 - page 14

    Installation Set Up 4-2 5975987A BARCODATA 708 260597 Scan adaptation The scanning can be switch by turning the Horizontal and Vertical scan connectors and the convergence connectors. To change the scanning, it is necessary to open the projector top cover and to rotate the chassis. For opening the projector's top cover, see Getting access to c ...

  • Barco DATA 708 - page 15

    Installation Set Up 1-3 5975987A BARCODATA 708 260597 A : Horizontal scan inversion Three connectors are used, one for each horizontal deflection coil. When changing the horizontal scan, insure that all three connectors are set in the same position. See position of the connectors for the corresponding projector configuration. B : Vertical scan inve ...

  • Barco DATA 708 - page 16

    Installation Set Up 4-4 5975987A BARCODATA 708 260597 ...

  • Barco DATA 708 - page 17

    Projector Set Up 5-1 5975987A BARCODATA 708 260597 5 PROJECT OR SET UP Projector Set Up The strap on the CPU unit allow a set up of the password mode. Gaining access to the strap - Open the top cover (see installation set up) - Open the chassis (see installation set up) Horizont al scan connectors Ver ti c al sc an connectors Convergence connectors ...

  • Barco DATA 708 - page 18

    Projector Set Up 5-2 5975987A BARCODATA 708 260597 ...

  • Barco DATA 708 - page 19

    Power Connection 6-1 5975987A BARCODATA 708 260597 6 POWER CONNECTION Power (mains) cord connection Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the front of the projector. See installation instructions before connecting to the supply V NOM 120 V olt I MAX 5 AMP ...

  • Barco DATA 708 - page 20

    Power Connection 6-2 5975987A BARCODATA 708 260597 ...

  • Barco DATA 708 - page 21

    Installation Adjustments 7-1 5975987A BARCODATA 708 260597 7 INST ALLA TION ADJUSTMENTS Entering the adjustment mode ADJUST MENT MODE Selec t a path f rom belo w: Select with or th en <ENTER > <EXI T> to ret u rn GUID ED RANDOM ACC ESS I NSTALLA TIO N SER VICE IRIS so urc e 1 Random Access Adjustment Guided Adjustment Installation (only ...

  • Barco DATA 708 - page 22

    Installation Adjustments 7-2 5975987A BARCODATA 708 260597 Overview flow chart installation mode. SCHEIMPF LUG ADJUSTM ENT <ENTER> t o conti nue <E XIT> t o return LOOS EN THE 4 LENS MOUN TING NUTS O N EA C H LE N S , UNTI L THE TAG OF EACH SCHEIMPFLUG RI NG CA N B E MOV ED T O I TS DE S IRE D POS ITI ON (1.4 M, 2.4 M OR 4.0 M SCREEN WI ...

  • Barco DATA 708 - page 23

    Installation Adjustments 7-3 5975987A BARCODATA 708 260597 ADJU STMENT MO DE Select a path from below: Select wi th or then <E NTER> <EXIT> t o return GUI DED RANDOM ACCESS INSTALLAT ION SERVICE IRIS source 1 Push the control disk up or down to highlight "Installation" and press ENTER. ENTER continues displaying a WARNING. EXI ...

  • Barco DATA 708 - page 24

    Installation Adjustments 7-4 5975987A BARCODATA 708 260597 Scheimpfug adjustment The scheimpfug correction can be adjusted separately for the three tubes within 3 ranges: range 1 : 1.4 m (55") to 1.9 m (75"), optimum screen width 1.4 m (55") range 2 : 1.9 m (75") to 3.2 m (126"), optimum screen width 2.4 m (94") range ...

  • Barco DATA 708 - page 25

    Installation Adjustments 7-5 5975987A BARCODATA 708 260597 Optical lens focusing OPTICAL LE NS FO CUSI NG <ENTE R> to con tinue <EXIT> to return 1. LOOSEN THE NUT O N THE REAR O F THE XXXX L ENS, ROTATE THE LENS BARREL TO FOCUS THE CEN TER OF THE IMA GE, THE N TIGHTE N THE NUT 2. LOOSEN THE NUT O N THE FRO NT OF T HE XXX X LENS A ND ROT ...

  • Barco DATA 708 - page 26

    Installation Adjustments 7-6 5975987A BARCODATA 708 260597 Raster centering The raster must be centered on the CRT screen surface of each tube, therefore, it is necessary to look into the lenses. Caution : To avoid eye discomfort while performing these adjust- ments, reduce the contrast and gradually increase the brightness level until the raster b ...

  • Barco DATA 708 - page 27

    Installation Adjustments 7-7 5975987A BARCODATA 708 260597 CRT projection angle adjustment The projection angle of the red and blue CRT's is dependent on the desired size of the projected image. If the centers of green, blue and red do not coincide, the CRT projection angle must be adjusted. Never try to correct this misalignment with the shif ...

  • Barco DATA 708 - page 28

    Installation Adjustments 7-8 5975987A BARCODATA 708 260597 Loosen the four hexagon screws A, A', B and B', upper and lower fixation latch. These screws fasten the cooling house of the red tube. Pivot the red CRT until the center of the red image coincides with the center of the green image. If the angle of the red CRT is corrected, tighte ...

  • Barco DATA 708 - page 29

    Installation Adjustments 7-9 5975987A BARCODATA 708 260597 ADJUSTM ENT MOD E source 1 Select wi th or then <E NTER> <EXIT> t o return GUIDE D RANDOM ACCESS INSTAL LATIO N SERVI CE IRIS After finishing the installation adjustments procedure, the 'Path selection' returns on the screen. You are now able to start the alignment pro ...

  • Barco DATA 708 - page 30

    Installation Adjustments 7-10 5975987A BARCODATA 708 260597 ...

  • Barco DATA 708 - page 31

    G2 Adjustment A-1 5975987A BARCODATA 708 260597 A G2 ADJUSTMENT Enter the adjustment mode by pressing ADJUST and highlight Service . Press ENTER to start up the service mode. G2 adjustment ADJU STMENT MO DE Select a path from below: Select wi th or then <E NTER> <EXIT> t o return source 1 GUI DE D RANDOM AC CESS INSTALLATION SERVICE IRI ...

  • Barco DATA 708 - page 32

    G2 Adjustment A-2 5975987A BARCODATA 708 260597 A green LED for each color is mounted on the driver board, below the CRT's. When selecting the G2 adjustment menu, these green LEDs must be out. If not, follow the procedure to adjust the G2 : - Loosen the retaining screws of the upper electronic chassis and pivot it to the lenses. - Adjust the G ...

  • Barco DATA 708 - page 33

    FORMULA OUTSIDE PACKAGE DIMENSIONS (Inches) CHEMICAL FAMILY FEDERAL STOCK NUMBER (FSN) GROSS WEIGHT (LBS) % TRESHOLD LIMIT VALUE (Units) ALLOYS AND METALLIC COATINGS % % PIGMENTS SOLVENTS ADDITIVES CATALYST VEHICLE HAZARDOUS MIXTURES OF OTHER LIQUIDS, SOLIDS, OR GASES APPEARANCE AND ODOR BOILING POINTS (°C.) SPECIFIC GRAVITY (H 2 O=1) VAPOR PRESSU ...

  • Barco DATA 708 - page 34

    STABILITY UNSTABLE STABLE CONDITIONS TO AVOID INCOMPATABILITY (Materials to avoid) HAZARDOUS DECOMPOSITION PRODUCTS HAZARDOUS POLYMERIZATION WILL NOT OCCUR CONDITIONS TO AVOID MAY OCCUR STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED WASTE DISPOSAL METHOD RESPIRATORY PROTECTION (Specific type) VENTILATION LOCAL EXHAUST MECHANICAL (General ...

Manufacturer Barco Category Projector

Documents that we receive from a manufacturer of a Barco DATA 708 can be divided into several groups. They are, among others:
- Barco technical drawings
- DATA 708 manuals
- Barco product data sheets
- information booklets
- or energy labels Barco DATA 708
All of them are important, but the most important information from the point of view of use of the device are in the user manual Barco DATA 708.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Barco DATA 708, service manual, brief instructions and user manuals Barco DATA 708. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Barco DATA 708.

Similar manuals

A complete manual for the device Barco DATA 708, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Barco DATA 708 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Barco DATA 708.

A complete Barco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Barco DATA 708 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Barco DATA 708, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Barco DATA 708, that we can find in the current document
3. Tips how to use the basic functions of the device Barco DATA 708 - which should help us in our first steps of using Barco DATA 708
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Barco DATA 708
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Barco DATA 708 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Barco DATA 708?

Use the form below

If you did not solve your problem by using a manual Barco DATA 708, ask a question using the form below. If a user had a similar problem with Barco DATA 708 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)