English dropdown-ico

Manual John Deere ET-3402-J

20 pages 0.14 mb
Download

Go to site of 20

Summary
  • John Deere ET-3402-J - page 1

    7 1/4 Inch Circular Saw Operator's Manual 1 CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! THIS MANUAL IS AN IMPORTANT PART OF THE CIRCULAR SAW AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT. ET -3402-J 7 1/4-INCH CIRCULAR SA W ...

  • John Deere ET-3402-J - page 2

    2 7 1/4 Inch Circular Saw Operator's Manual Congratulations on the purchase of your new Circular Saw! You can be assured your circular saw was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance. This operator's manual was compiled for your bene ...

  • John Deere ET-3402-J - page 3

    7 1/4 Inch Circular Saw Operator's Manual 3 T able of Content SAFETY .................................................................................................................. 4-11 GENERAL SAFETY RULES .................................................................. 4-11 FUNCTIONAL DESCRIPTION ........................................ ...

  • John Deere ET-3402-J - page 4

    4 7 1/4 Inch Circular Saw Operator's Manual W ARNI N G W A R N I NG SI N T HE M A NUA LS . W A RN I NG SI N T HE M A NUA LS . CA U T I ON OC A UT I ON S IN O T H E M A N UA L S OC AUT I ON S IN O T H E M A N UA L S OC AUT I ON S IN O T H E M A N UA L S OC A UT I ON S IN O T H E M A N UA L S RECOGNIZE SAFETY INFORMATION This is the safety alert ...

  • John Deere ET-3402-J - page 5

    7 1/4 Inch Circular Saw Operator's Manual 5 KEEP WORK AREA CLEAN AND WELL LIT. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. Don't expose power tools to rain. Don't use power tools in damp or wet locations. Keep work area well lit. Don't use tool in presence of flammable liquids or gases. Power too ...

  • John Deere ET-3402-J - page 6

    6 7 1/4 Inch Circular Saw Operator's Manual DON'T OVERREACH Keep proper footing and balance at all times. MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and replace if damaged, have repaired by authorized se ...

  • John Deere ET-3402-J - page 7

    7 1/4 Inch Circular Saw Operator's Manual 7 OUTDOOR USE EXTENSION CORDS When tool is used outdoors, use only extension cords intended for use outdoors and so marked. STAY ALERT Watch what you are doing. Use common sense. Do not operate tool when you are tired. CHECK DAMAGED PARTS Before further use of the tool, a guard or other part that is da ...

  • John Deere ET-3402-J - page 8

    8 7 1/4 Inch Circular Saw Operator's Manual CAUTION ALWAYS KEEP THE MOTOR AIR VENT FULLY OPENED A constantly open motor air vent is necessary to allow air to come in and out for cooling the motor. Do not allow it to become clogged up, even if dust is blown through it. OPERATE POWER TOOLS AT THE RATED VOLTAGE Operate power tools at voltages spe ...

  • John Deere ET-3402-J - page 9

    7 1/4 Inch Circular Saw Operator's Manual 9 CAUTION SUPPORT LARGE PANELS Large panels must be supported as shown in Fig. 1 to minimize the risk of blade pinching and kickback. When cutting operation requires the resting of saw on the work piece, the saw shall be rested on the larger portion and the smaller piece cut off. USE RIP FENCE Always u ...

  • John Deere ET-3402-J - page 10

    10 7 1/4 Inch Circular Saw Operator's Manual LOWER GUARDS Raise lower guard with the retracting handle (Lever). ADJUSTMENTS Before cutting be sure depth and bevel adjustments are tight. USE ONLY CORRECT BLADES IN MOUNTING Do not use blades with incorrect size holes. Never use defective or incorrect blade washers or bolts. AVOID CUTTING NAILS I ...

  • John Deere ET-3402-J - page 11

    7 1/4 Inch Circular Saw Operator's Manual 11 EXTENSION CORD Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table shows the correct size ...

  • John Deere ET-3402-J - page 12

    12 7 1/4 Inch Circular Saw Operator's Manual Functional Description MODEL: ET-3402-J CIRCULAR SAW NAME OF PARTS: (Fig. 3) NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read ...

  • John Deere ET-3402-J - page 13

    7 1/4 Inch Circular Saw Operator's Manual 13 Operation APPLICATIONS: Cutting various types of wood. PRE-OPERATION: Before using the Electric Power Tool, complete the following preparations: 1. Power source: Ensure that the power source to be utilized conforms to the power requirements specified on the product nameplate. 2. Power switch: Ensure ...

  • John Deere ET-3402-J - page 14

    14 7 1/4 Inch Circular Saw Operator's Manual Operation OPERATION: CUTTING PROCEDURES: CAUTION: RECHECK THAT THE SAW BLADE IS SECURELY CLAMPED. CONFIRM THAT THE CLAMP LEVER FOR ADJUSTING THE SLOT DEPTH, THE WING-BOLT FOR ADJUSTING THE ANGLE OF INCLINATION. GRIP THE SAW AS SHOWN IN FIG. 2 AND BE SURE THE CORD IS FREE TO MOVE THROUGH THE ENTIRE C ...

  • John Deere ET-3402-J - page 15

    7 1/4 Inch Circular Saw Operator's Manual 15 Operation POCKET CUTTING: CAUTIONS: RELEASE TRIGGER AFTER CUTTING WORK AND DISCON- NECT PLUG FROM POWER SUPPLY BEFORE ANY ADJUST- MENT. NEVER TIE OR WEDGE THE SAFETY COVER IN A RAISED POSITION. OPERATION (CONTINUED): 1. Mark the desired cutting area clearly with lines all side. (See Fig. 9) 2. Set d ...

  • John Deere ET-3402-J - page 16

    16 7 1/4 Inch Circular Saw Operator's Manual Operation MOUNTING AND DISMOUNTING THE SAW BLADE: CAUTION: TO AVOID SERIOUS ACCIDENT, ENSURE THE SWITCH IS IN THE OFF POSITION, AND THE POWER SOURCE IS DISCON- NECTED. 1. Dismounting the saw blade (Fig. 10): To replace the saw blade, push the lock lever, then loosen the hexagonal bolt with the wrenc ...

  • John Deere ET-3402-J - page 17

    7 1/4 Inch Circular Saw Operator's Manual 17 Maintenance and Inspection MAINTENANCE AND INSPECTION: CAUTION: BE SURE TO SWITCH POWER OFF AND DISCONNECT THE PLUG DURING MAINTENANCE AND INSPECTION. 1. Inspecting the saw blade: Since use of a dull saw blade will degrade efficiency and cause possible motor malfunction, sharpen or replace the saw b ...

  • John Deere ET-3402-J - page 18

    18 7 1/4 Inch Circular Saw Operator's Manual STANDARD ACCESSORIES: CAUTION: RECOMMENDED ACCESSORIES FOR THE ELECTRIC POWER TOOL ARE MENTIONED IN THIS MANUAL. THE USE OF ANY OTHER ATTACHMENT OR ACCESSORY IS HAZARDOUS. 1. Saw Blade 1 2. Wrench 1 3. Wiring Bolt (B) 1 4. Lock Spring 1 SERVICE AND REPAIRS All quality tools will eventually require s ...

  • John Deere ET-3402-J - page 19

    7 1/4 Inch Circular Saw Operator's Manual 19 Notes ...

  • John Deere ET-3402-J - page 20

    20 7 1/4 Inch Circular Saw Operator's Manual Manufactured for Deere & Company, Moline, Illinois 61265 7 1/4-Inch Circular Saw Operator's Manual 111 Code No. C99112361 N #37-0688-090403 © Copyright 2003. John Deere ...

Manufacturer John Deere Category Saw

Documents that we receive from a manufacturer of a John Deere ET-3402-J can be divided into several groups. They are, among others:
- John Deere technical drawings
- ET-3402-J manuals
- John Deere product data sheets
- information booklets
- or energy labels John Deere ET-3402-J
All of them are important, but the most important information from the point of view of use of the device are in the user manual John Deere ET-3402-J.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals John Deere ET-3402-J, service manual, brief instructions and user manuals John Deere ET-3402-J. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product John Deere ET-3402-J.

Similar manuals

A complete manual for the device John Deere ET-3402-J, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use John Deere ET-3402-J by users. Manuals are usually written by a technical writer, but in a language understandable to all users of John Deere ET-3402-J.

A complete John Deere manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual John Deere ET-3402-J - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the John Deere ET-3402-J, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the John Deere ET-3402-J, that we can find in the current document
3. Tips how to use the basic functions of the device John Deere ET-3402-J - which should help us in our first steps of using John Deere ET-3402-J
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with John Deere ET-3402-J
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of John Deere ET-3402-J in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning John Deere ET-3402-J?

Use the form below

If you did not solve your problem by using a manual John Deere ET-3402-J, ask a question using the form below. If a user had a similar problem with John Deere ET-3402-J it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)