Manual Polaroid 160

80 pages 0.87 mb
Download

Go to site of 80

Summary
  • Polaroid 160 - page 1

    E INSTRUCTION MANUAL ...

  • Polaroid 160 - page 2

    2 For Proper and Safe Use .................. 4 GETTING ST ARTED Names of Parts ................................ 10 Attaching the Camera Strap ............ 16 Inserting the Battery ........................ 17 Battery-condition Indicator .............. 18 Loading the Film .............................. 19 BASIC OPERA TION Fully Automatic Operation .. ...

  • Polaroid 160 - page 3

    3 ADV ANCED OPERA TION Selecting the AF Mode .................... 36 Area AF ........................................ 37 Focus-area Indicator Controls ...... 38 Spot AF.......................................... 40 Focus Lock - Spot AF .................... 41 T arget AF ...................................... 42 Selecting the Flash Mode ............. ...

  • Polaroid 160 - page 4

    4 Read and understand all warnings and cautions before using this product. Using batteries improperly can cause them to leak harmful solutions, overheat, or explode which may damage property or cause personal injury . Do not ignore the following warnings: • Only use the batteries specified in this instruction manual. • Do not install the batter ...

  • Polaroid 160 - page 5

    5 •T ape over lithium battery contacts to avoid short-circuiting during disposal; always follow local regulations for battery disposal. • Do not disassemble this product. Electric shock may cause injury if a high voltage circuit inside the product is touched. T ake the product to a Minolta Service Facility when repairs are required. • Immedia ...

  • Polaroid 160 - page 6

    FOR PROPER AND SAFE USE 6 • Do not fire the flash directly into the eyes. It may damage eyesight. • Do not fire the flash at vehicle operators. It may cause a distraction or temporary blindness which may lead to an accident. • Do not look directly at the sun or strong light sources through the viewfinder . It may damage your eyesight or cause ...

  • Polaroid 160 - page 7

    7 Continued on next page. •T ake the product to a Minolta Service Facility when repairs are required. CAUTION • Do not use or store the product in a hot or humid environment such as the glove compartment or trunk of a car . It may damage the product and batteries which may result in burns or injuries caused by heat, fire, explosion, or leaking ...

  • Polaroid 160 - page 8

    FOR PROPER AND SAFE USE 8 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not approved by the par ...

  • Polaroid 160 - page 9

    9 If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and t ...

  • Polaroid 160 - page 10

    NAMES OF P ARTS 10 * This camera is a sophisticated optical instrument. Care should be taken to keep these surfaces clean. Refer to the care and storage section at the back of this manual (p. 73). BODY The 160 quartz-date model is illustrated. AF/Meter window* Flash* (p. 44) Self-timer/Remote-control lamp* (p. 54, 65) Lens* Back-cover release (p. 1 ...

  • Polaroid 160 - page 11

    11 GETTING ST ARTED Continued on next page. Shutter-release button (p. 25) Data panel (p. 12) V iewfinder* (p. 13) Date button (p. 57) (Quartz Date model only) Flash-mode/Select button (p. 44, 57) Main switch (p. 22) Film window (p. 19) Strap eyelet (p. 16) Battery-chamber door (p. 17) Zoom lever (p. 23) Back cover (p. 19) Drive-mode/Adjust button ...

  • Polaroid 160 - page 12

    12 NAMES OF P ARTS Battery-condition indicator (p. 18 ) Frame counter (p. 21 ) Film-transport signals (p. 21 ) Cartridge mark (p. 34 ) Self-timer indicator (p. 53 ) Date/T ime display (p. 57 ) (Quartz-Date model only) Autoflash Autoflash with red-eye reduction Fill-flash Flash cancel Night Portrait (with red-eye reduction) Exposure Compensation ( 1 ...

  • Polaroid 160 - page 13

    13 Continued on next page. GETTING ST ARTED VIEWFINDER Area AF (p. 37) All focus frames and focus- area indicators are shown. This camera features a sophisticated matrix AF indication system that indicates the area of focus. Focus-frame Display Spot AF (p. 40) T arget AF (p. 42) For focus-area indicators in Area AF , see pages 24 and 27. ...

  • Polaroid 160 - page 14

    14 NAMES OF P ARTS Close-framing guide (p. 32)* Focus-area indicator (p. 27)** V aries according to the subject. VIEWFINDER Focus frames (Area AF) * The close-framing guide appears in Area, spot, and target-AF modes. ** The focus-area indicator is displayed in the Area-AF mode. ...

  • Polaroid 160 - page 15

    15 GETTING ST ARTED VIEWFINDER Focus lamp (green) With the shutter-release button pressed partway down - Glows: focus confirmed Blinks rapidly: subject is too close Blinks slowly: focus not confirmed (p. 30) Flash lamp (orange) With the shutter-release button pressed partway down - Glows: flash is charged and ready Blinks rapidly: flash charging Bl ...

  • Polaroid 160 - page 16

    16 1. Pass the small loop of the strap through the strap eyelet on the camera. AT T ACHING THE CAMERA STRAP • Button keys are attached to the strap. Use the larger key to open the battery-chamber door , and the smaller key to push the manual-rewind button. Button keys 2. Pass the the other end of the strap through the small loop and tighten. 1 2 ...

  • Polaroid 160 - page 17

    17 • Quartz-date model: after installing the battery , the date and time must be set, see page 59. • When changing batteries, always turn the camera off. INSERTING THE BA TTER Y The camera uses one 3-volt CR123A or DL123A lithium battery . 1. Open the battery-chamber door using the larger button key on the camera strap. 2. Insert the battery . ...

  • Polaroid 160 - page 18

    18 The indicator briefly appears. Power is sufficient for all camera operations. The indicator blinks and no other indicators are displayed on the data panel. The shutter will not release. Replace the battery immediately . Each time the camera is turned on, an indicator will appear on the data panel to indicate the power status of the battery . The ...

  • Polaroid 160 - page 19

    19 1. Slide the back-cover release down to open the back cover . • Before opening the back cover , look through the film window to confirm that film is not currently loaded. LOADING THE FILM • If the back cover does not open, turn the camera off and on to release the film- chamber lock. • Use only DX-coded 35mm film rated between ISO 25 and 3 ...

  • Polaroid 160 - page 20

    20 LOADING THE FILM 2. Place the film cartridge into the film chamber . 3. Extend the film leader to the film-tip mark. The film must lay flat. • If the film tip extends beyond the index mark, push the excess film back into the cartridge. ...

  • Polaroid 160 - page 21

    21 4. Close the back cover . • The film automatically advances to the first frame and “ 1 ” appears in the data-panel frame counter. • If the film has been loaded improperly , “0” will blink on the frame counter and the shutter will not release. Open the back cover and repeat the loading procedure. • Once the film is loaded, the batte ...

  • Polaroid 160 - page 22

    22 1. Press the main switch to turn the camera on. •T o conserve battery power , the auto-power- off function will turn the camera of f eight minutes after the last operation. • Do not obstruct or hold the lens barrel. 2. Hold the camera steadily . Do not cover the flash, lens, or AF windows with your fingers. • For vertically framed pictures ...

  • Polaroid 160 - page 23

    23 3. Look through the viewfinder and press the zoom lever to zoom the lens. • The viewfinder will adjust to match the lens’ field of view . T(elephoto): zoom in W(ide angle): zoom out Continued on next page. BASIC OPERA TION ...

  • Polaroid 160 - page 24

    24 FULL Y AUT OMA TIC OPERA TION 4. Place the subject within the Area AF frame. The focus frame will automatically change to a focus-area indicator to confirm the subject. • The Area-AF mode (p. 37) is automatically set when the camera is turned on. • The focus-area indicator shows the area the camera will focus on. • The shape of the focus-a ...

  • Polaroid 160 - page 25

    25 Continued on next page. 5. Press the shutter-release button partway down. • The status of the AF system and flash are indicated by the lamps next to the viewfinder . Focus lamp (green) Glows: focus confirmed Blinks rapidly: subject is too close Blinks slowly: focus not confirmed (p. 30) Flash lamp (orange) Glows: flash is charged and ready Bli ...

  • Polaroid 160 - page 26

    26 FULL Y AUT OMA TIC OPERA TION 6. When the green focus lamp glows, press the shutter-release button all the way down to take the picture. • Press the shutter-release button with slow , steady pressure. • The film automatically advances to the next frame. • Always turn the camera off after use. ...

  • Polaroid 160 - page 27

    27 As long as the subject is located within the Area-AF focus frame, even if it is not centered, the camera will automatically locate the subject and indicate it with the focus-area indicator . The shape of focus-area indicator varies with the subject shape, see the sample illustrations below . Portrait (The camera focuses on the two foreground sub ...

  • Polaroid 160 - page 28

    28 FOCUS LOCK - AREA AF The focus-lock function allows the camera to be focused on a certain subject and then the picture can be recomposed to arrange the subject at a different position within the image area. 1. With focus-area indicator around the subject, press and hold the shutter-release button partway down. • The green focus lamp will glow ...

  • Polaroid 160 - page 29

    29 FOCUSING RANGE BASIC OPERA TION If the subject is too close, the green focus lamp blinks rapidly and the shutter is locked. The subject must be beyond the minimum focusing distance. If the subject is extremely close, the green focus lamp may blink slowly and the shutter will release, but the focus will not be sharp. The subject must be within th ...

  • Polaroid 160 - page 30

    30 The camera may not be able to focus in certain situations. At this time, the focus-lock function (p. 28, 41) can be used to focus on an object at the same distance as your subject, and then the image can be recomposed to take the picture. When your subject is near a very bright object or area. When two subjects overlap in the focus frame. SPECIA ...

  • Polaroid 160 - page 31

    31 When a low-contrast area fills the focus frame. When the subject is composed of a regular repeating pattern. The green focus lamp will blink slowly to warn that focus cannot be confirmed. The shutter can be released and the focus will be set to infinity; when using the flash, the focus is set between 2.3 - 6.8m (7.5 - 22.3 ft.) depending on the ...

  • Polaroid 160 - page 32

    32 Because of parallax, the image seen in the viewfinder and the image recorded with the camera are not exactly the same. Parallax becomes significant with close subjects. A close-framing guide automatically appears in the viewfinder when the image needs to be recomposed to eliminate the effect of parallax. The close-framing guide appears in Area A ...

  • Polaroid 160 - page 33

    33 1. With the focus-area indicator on the subject, press and hold the shutter release button partway down. • The green focus lamp should glow to confirm the focus is locked. BASIC OPERA TION 2. While pressing the shutter-release button partway down, recompose the picture so that the top of the subject falls below the close-framing guide. Press t ...

  • Polaroid 160 - page 34

    34 REWINDING THE FILM The camera automatically rewinds the film after the last exposure is taken. When the cartridge mark blinks on the data panel, the film has been rewound. Open the back cover and remove the film. • The film-chamber lock is release during rewind. Do not open the back cover until the cartridge mark blinks on the data panel. Neve ...

  • Polaroid 160 - page 35

    35 • If the rewind motor stops before the film has been completely rewound, all the indicators on the data panel will blink. Remove and insert the battery . • Although more pictures than specified on the film package may be taken, the film processor may only print the number specified on the film cartridge. Gently press the manual-rewind button ...

  • Polaroid 160 - page 36

    36 SELECTING THE AF MODE Three auto focus (AF) modes can be selected: Area AF , spot AF , and target AF . Press the AF mode button until the desired AF indicator appears on the data panel. Area AF (p. 37) Spot AF (p. 40) T arget AF (p. 42) • Spot-AF and target-AF mode is reset to Area AF when the camera is turned off. ...

  • Polaroid 160 - page 37

    37 AREA AF 1. Press the AF mode button until the Area-AF indicator appears on the data panel. 2. Place the subject within the Area-AF frame. • The focus frame will automatically change to a focus-area indicator to confirm the subject. 3. Press the shutter-release button to take the picture. focus-area indicator Area-AF frame ADV ANCED OPERA TION ...

  • Polaroid 160 - page 38

    38 FOCUS-AREA INDICA TOR CONTROLS The display of the focus-area indicator can be controlled with a custom function. CUSt-1:1 - The focus-area indicator automatically appears when looking through the viewfinder . CUSt-1:2 - The focus-area indicator appears when the shutter-release button is pressed partway down. CUSt-1:3 - The focus-area indicator i ...

  • Polaroid 160 - page 39

    39 2. T o change the setting, press the adjust button or zoom lever until the desired setting number is displayed. ADV ANCED OPERA TION 3. Press the AF mode button once to enter the new setting. • The camera will return to the shooting mode automatically after five seconds. Pressing the AF mode button again or pressing the shutter-release button ...

  • Polaroid 160 - page 40

    40 SPOT AF The camera focuses on a subject within the spot AF frame. This mode can be used to single out a specific subject from a group. 1. Press the AF mode button until the spot-AF indicator appears on the data panel. • The spot-AF focus frame appears in the viewfinder . 2. Place the subject in the spot-AF focus frame. Press the shutter-releas ...

  • Polaroid 160 - page 41

    41 FOCUS LOCK - SPOT AF The focus-lock function allows the camera to be focused on a certain subject and then the picture can be recomposed to arrange the subject at a different position within the image area. ADV ANCED OPERA TION 1. With subject in the focus frame, press and hold the shutter-release button partway down. • If the green focus lamp ...

  • Polaroid 160 - page 42

    42 T ARGET AF T arget-AF focus frame The target AF is ideal for moving subjects. The camera continually calculates the focus even when the shutter-release button is held partway down. Predictive focus control ensures someone moving toward the camera will be in focus; predictive focus control adjusts the focus during the slight delay between the tim ...

  • Polaroid 160 - page 43

    43 3. Press and hold the shutter-release button partway down until the green focus lamp glows. •T arget AF has no focus-lock function. The camera continuously calculates focus while the shutter button is held partway down. • Predictive focus control is activated when the focus lamp glows. • If the subject becomes too close, the green focus la ...

  • Polaroid 160 - page 44

    44 SELECTING FLASH MODE The following flash modes can be selected: Press the flash-mode button until the desired flash-mode indicator appears on the data panel. Autoflash (p. 47) Autoflash with red-eye reduction (p. 48) Fill-flash (p. 49) ...

  • Polaroid 160 - page 45

    45 • When the camera is turned off, the fill-flash, flash cancel, night portrait, or exposure compensation mode will be reset to autoflash or autoflash with red- eye reduction, whichever of the two modes was set last. Flash cancel (p. 50) Night portrait (p. 51) Exposure compensation (p. 52) ( 160 model only) ADV ANCED OPERA TION ...

  • Polaroid 160 - page 46

    46 The flash range depends on the film speed and focal length in use. Because of the optical system, the flash range is not the same at the lens’ wide-angle position as it is at the telephoto position. T o ensure proper exposure, the subject must be within the flash range. FLASH RANGE The distances are based on use with color negative film. ISO10 ...

  • Polaroid 160 - page 47

    47 AUTOFLASH The flash will fire automatically in low-light or back-lit situations. Press the flash-mode button until the autoflash indicator appears on the data panel to set the flash mode. • When the orange flash lamp blinks quickly , the flash is charging. The shutter cannot be released until the flash is charged; the orange flash lamp will gl ...

  • Polaroid 160 - page 48

    48 AUTOFLASH WITH RED-EYE REDUCTION The flash will fire a few short bursts before the main flash burst to reduce red-eye; an effect caused by light reflected from the retina. Used in low-light condition when taking photographs of people or animals, the pre-flashes contract the pupils of the subject’s eyes. The flash will fire automatically in low ...

  • Polaroid 160 - page 49

    49 FILL-FLASH The flash fires with each exposure regardless of the amount of ambient light. Fill-flash can be used to reduce harsh shadows caused by strong direct light or sunshine. Press the flash-mode button until the fill-flash indicator appears on the data panel to set the flash mode. ADV ANCED OPERA TION ...

  • Polaroid 160 - page 50

    50 FLASH CANCEL The flash will not fire in this mode. Use flash cancel when flash photography is prohibited, natural light is desired to illuminate the subject, or the subject is beyond the flash range. The camera-shake warning may appear in this mode. Press the flash-mode button until the flash- cancel indicator appears on the data panel to set th ...

  • Polaroid 160 - page 51

    51 In night-portrait mode, the camera balances the flash and existing light exposure so you can take beautiful portraits at sunset or at night. The flash will fire with each exposure regardless of the amount of ambient light. Red-eye reduction is used with the night-portrait mode. Press the flash-mode button until the night- portrait indicator appe ...

  • Polaroid 160 - page 52

    52 EXPOSURE COMPENSA TION (160 MODEL ONL Y) The multi-segment metering can expose for most situations: back lighting, and directly lit snow scenes. However , under certain conditions the meter can be deceived by high-key scenes like white interiors or foggy landscapes. This mode increases the exposure by 1.5 Ev . The flash is disabled. Press the fl ...

  • Polaroid 160 - page 53

    53 SELF-TIMER 1. With the camera on a tripod, press the drive-mode button until the self-timer indicator appears on the data panel. 2. Frame the subject as described in the manual. • Focus lock can be used with Area AF and spot AF . •W ith target AF or when focus lock is not used, the focus is set just before the exposure. Make sure the subject ...

  • Polaroid 160 - page 54

    54 3. Press the shutter-release button all the way down to begin the countdown. • The self-timer indicator will blink on the data panel. The self-timer lamp on the front of the camera will blink slowly during the countdown, then rapidly just before the shutter is released. •T o cancel the self-timer , press the drive-mode button again or turn t ...

  • Polaroid 160 - page 55

    55 In this mode, the camera continuously takes pictures as long as the shutter-release button is held down. The camera will take one picture every 2.2 seconds. When the flash is used, the rate may be slower because the flash must recharge between frames. 1. Press the drive-mode button until the continuous-advance indicator appears on the data panel ...

  • Polaroid 160 - page 56

    56 CONTINUOUS ADV ANCE (160 MODEL ONL Y) 2. Frame the subject as described in the manual. 3. Press the shutter-release button all the way down and hold to begin taking pictures. • Focus will be adjusted between exposures. • Continuous advance remains in effect until the drive mode is reset. • When using target AF , predictive focus control is ...

  • Polaroid 160 - page 57

    BUTT ONS FOR THE DA TE FUNCTION Select button Adjust button Date button 57 FOR OWNERS OF THE QUARTZ-DA TE MODEL The quartz-date model has date and time imprinting and remote-control operation. DA TE AND TIME IMPRINTING The imprinting feature enables the date or time to be printed onto the lower-right portion of the picture. The date is recorded as ...

  • Polaroid 160 - page 58

    58 IMPRINTING THE DA TE OR TIME FOR OWNERS OF THE QUARTZ-DA TE MODEL Press the date button to select the date imprinting format. • The display will change as follows: • If the date/time display is blinking, the calendar and clock need to be reset (p. 59). No information will be imprinted until the date and time are entered. Date imprinting Day/ ...

  • Polaroid 160 - page 59

    YY MM DD hh mm 59 SETTING THE DA TE OR TIME Continued on next page. Note: the date and time must be reset each time the battery is replaced. 1. T urn the camera on. Press the date button until “SEt” appears on the data panel. 2. Press the select (SEL) button until the item to be adjusted blinks. • Each time the select button is pressed, the n ...

  • Polaroid 160 - page 60

    60 FOR OWNERS OF THE QUARTZ-DA TE MODEL 3. Press the adjust (ADJ) button or zoom lever to change the blinking item. • The numerals continues to change as long as the button is held down. • Pressing the W side of the zoom lever counts down, the T side counts up. 4. Repeat steps 2 and 3 until all items in the date and time display are correct. 5. ...

  • Polaroid 160 - page 61

    61 CHANGING THE DA TE FORMA T 1. Press the date button until “SEt” appears on the data panel. 2. Press and hold the select (SEL) button for more than 2 seconds until all items on the date display blink. Continued on next page. ADV ANCED OPERA TION • Pressing the select (SEL) button until the date/time display stops blinking can also set the c ...

  • Polaroid 160 - page 62

    62 3. Press the adjust (ADJ) button or zoom lever to change the display format. • The date format changes as follows: `Y M D M D`Y D M`Y 4. Press the date button to set the date format. • The camera will return to the shooting mode automatically after five seconds. Pressing the date button again or pressing the shutter-release button partway do ...

  • Polaroid 160 - page 63

    63 REMOTE CONTROL OPERA TION The quartz-date model can be controlled by the IR remote control RC-3 (sold separately). The remote control allows remote camera operation up to 5 meters (16.5 feet) away . NAMES OF P ARTS Emitter window Delay button Release button Battery chamber Continued on next page. ADV ANCED OPERA TION ...

  • Polaroid 160 - page 64

    64 T AKING PICTURES USING THE REMOTE CONTROL 1. Place the camera on a tripod. Point the camera so that the subject is within in the focus frames. FOR OWNERS OF THE QUARTZ-DA TE MODEL 2. Press the drive-mode button until the remote-control indicator appears on the data panel ...

  • Polaroid 160 - page 65

    65 3. Point the remote control toward the front of the camera and press either the release button (•) or the delay button (2s) to take the picture. • If the release button (•) is pressed, the self- timer/remote-control lamp on the front of the camera will blink once before the picture is taken. If the delay button (2s) is pressed, the lamp wi ...

  • Polaroid 160 - page 66

    66 FOR OWNERS OF THE QUARTZ-DA TE MODEL •T o save power , the camera automatically shuts down if the shutter is not released in approximately 8 minutes. • Under fluorescent or extremely bright lighting, or with backlit subjects, the remote control may not operate or the effective distance may be reduced. • The remote control mode will remain ...

  • Polaroid 160 - page 67

    67 FOCUS LOCK IN REMOTE CONTROL MODE Continued on next page. 1. Select remote-control mode using the drive-mode button. 2. Place the subject in the focus frames and press the shutter- release button partway down to confirm the focus; the green focus lamp will glow and remain lit. • It the focus lamp does not remain lit after pressing the shutter- ...

  • Polaroid 160 - page 68

    68 3. Recompose the picture. • The focus frames or focus-area indicator will disappear after releasing the shutter button. The focus lamp will remain lit indicating the focus is locked. FOR OWNERS OF THE QUARTZ-DA TE MODEL 4.Point the remote control toward the front of the camera, press either the release button (•) or delay button (2s). • Th ...

  • Polaroid 160 - page 69

    69 CHANGING THE REMOTE-CONTROL BA TTER Y The remote control uses a 3V lithium battery (CR2032). When pressing the remote-control buttons does not release the shutter , the battery needs to be replaced. The supplied battery should be sufficient for approximately ten years of operation. 1. Pull out the battery chamber as shown and remove the old batt ...

  • Polaroid 160 - page 70

    70 VIEWFINDER BRIGHTNESS The relative brightness of the AF frame or focus-area indicator can be adjusted. The brightness of the frame lines will continue to adjust automatically in relation to the new level. 1. Press and hold the AF mode button for about two seconds until “CUSt-1” appears on the top of the data panel. • The number blinking in ...

  • Polaroid 160 - page 71

    71 3. Press the adjust button or zoom lever until the desired brightness level is displayed. 4. Press the AF mode button or press the shutter-release button partway down to set the brightness level. • The data-panel display returns to normal. • The new brightness level will remain in effect even if the camera is turned off or the battery is cha ...

  • Polaroid 160 - page 72

    On February 20th, 1962, John Glenn became the first American to orbit the Earth. On board his Friendship 7 spacecraft was a Minolta Hi-matic camera to record that historic event. The 4 hour , 55 minute, and 23 second flight orbited the Earth three times at an average speed of 28,000 kph (17,500 mph). Mr . Glenn visited our Sakai camera factory in J ...

  • Polaroid 160 - page 73

    73 OPERA TING TEMPERA TURE AND CONDITIONS • This camera is designed for use from -10 to 40°C (14 to 104°F). • Never leave the camera where it may be subjected to extreme temperatures such as in the glove compartment of a car . • At colder temperatures, the data panel response time will be slow . At higher temperatures, the display will temp ...

  • Polaroid 160 - page 74

    74 CARE AND ST ORAGE • When photographing in cold weather , it is recommend that you keep the camera and spare batteries inside your coat to keep them warm when you are not shooting. Cold batteries will regain some of their charge when they warm up. • This camera is not waterproof, dust-proof, or sand-proof. Care should be taken when using of t ...

  • Polaroid 160 - page 75

    75 CLEANING • Keep the AF window clean to ensure accurate focus. • If the camera body is dirty , gently wipe it clean with a soft, clean, dry cloth. •T o clean the lens surface, first brush away any dust or sand then, if necessary , moisten a lens tissue with lens cleaning fluid and gently wipe the lens in a circular motion, starting from the ...

  • Polaroid 160 - page 76

    76 BEFORE IMPORT ANT EVENTS • Check camera operation carefully and take test photographs. Purchase a spare battery . • Minolta is not responsible for any loss which may occur due to an equipment malfunction. STORAGE When storing the camera for extended periods, please follow these guidelines: • Store the camera in a cool, dry , well-ventilate ...

  • Polaroid 160 - page 77

    77 CAMERA ERROR If all the indicators on the data panel blink, or the data panel is blank and the camera will not function with a recently installed battery , remove and reinsert the battery . If the camera does not resume normal operation, or the camera malfunctions repeatedly , contact an authorized Minolta Service Facility . QUESTIONS AND SER VI ...

  • Polaroid 160 - page 78

    78 Camera T ype: 35mm lens-shutter camera Lens: 37.5-140mm f/5.4 - 1 1.7 lens (140 model) 37.5-160mm f/5.4 - 12.4 lens (160 model) 6 elements in 6 groups Focusing Range: (140 model) (160 model) ( W ): 0.6m - ∞ (2.0 ft - ∞ ) 0.6m - ∞ (2.0 ft - ∞ ) ( T ): 0.80m - ∞ (2.6 ft - ∞ ) 0.95m - ∞ (3.1 ft - ∞ ) Film Speed: Settings Automatic f ...

  • Polaroid 160 - page 79

    Battery: One 3-volt CR123A lithium battery Battery-condition indication: 3-stage indication Battery performance: approx. 10 rolls based on Minolta's standard test method using 24-exposure rolls with flash for 50% of the exposures. V iewfinder: Magnification: 0.38X - 1.35X (140 model) ; 0.38X - 1.51X (160 model) Field of View: 85% (at 3m) Eye-r ...

  • Polaroid 160 - page 80

    © 2001 Minolta Co., Ltd. under the Berne Convention and Universal Copyright Convention 9222-2472-1 1 NI-A112 Minolta Co., Ltd. 3-13, 2-Chome, Azuchi-Machi, Chuo-Ku, Osaka 541-8556, Japan Minolta Europe GmbH Minoltaring 1 1, D-30855 Langenhagen, Germany Reparatur/Repair Senator-Helmken-Strasse 1, D-28197 Bremen, Germany Minolta France S.A. 365 Rout ...

Manufacturer Polaroid Category Digital Camera

Documents that we receive from a manufacturer of a Polaroid 160 can be divided into several groups. They are, among others:
- Polaroid technical drawings
- 160 manuals
- Polaroid product data sheets
- information booklets
- or energy labels Polaroid 160
All of them are important, but the most important information from the point of view of use of the device are in the user manual Polaroid 160.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Polaroid 160, service manual, brief instructions and user manuals Polaroid 160. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Polaroid 160.

Similar manuals

A complete manual for the device Polaroid 160, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Polaroid 160 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Polaroid 160.

A complete Polaroid manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Polaroid 160 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Polaroid 160, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Polaroid 160, that we can find in the current document
3. Tips how to use the basic functions of the device Polaroid 160 - which should help us in our first steps of using Polaroid 160
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Polaroid 160
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Polaroid 160 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Polaroid 160?

Use the form below

If you did not solve your problem by using a manual Polaroid 160, ask a question using the form below. If a user had a similar problem with Polaroid 160 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)