English dropdown-ico

Manual Craftsman 137.24885

30 pages 4.05 mb
Download

Go to site of 30

Summary
  • Craftsman 137.24885 - page 1

    Operator's Manual ® 10 in. TABLE SAW WiTH STAND Model No. 137.248850 CAUTION: Before using this Table Saw, read this manual and follow all its Safety Rules and Operating instructions Customer Help Line For Technical Support 1-800,.843-1682 e Safety Instructions • Installation o Operation e Maintenance • Parts List Sears Parts & Repair ...

  • Craftsman 137.24885 - page 2

    SECTION PAGE Warranty ................................................................ 2 Product Specifications ........................................... 2 Power Tool Safety ................................................. 3 Table Saw Safety .................................................. 4 Electrical Requirements and Safety ................. ...

  • Craftsman 137.24885 - page 3

    GENERAL SAFETY iNSTRUCTiONS Read and understand all the instructions below before using the power tool. These safety instructions are not meant to cover every possible condition that could occur. As with any power tool, common sense, vigilance and due care must be used. 1. READ and become familiar with the entire Operator' 17. s Manual. LEARN ...

  • Craftsman 137.24885 - page 4

    2. 3. 4. ALWAYS USE SAW BLADE GUARD, splitter and anti-kickback pawls for every through-sawing operation. Through-sawing operations are those in which the blade cuts completely through the workpiece when ripping or crosscutting. Always be sure blade guard is tightened securely. ALWAYS HOLD WORK FIRMLY against the miter gauge or rip fence. ALWAYS US ...

  • Craftsman 137.24885 - page 5

    GROUNDING iNSTRUCTiONS IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least resistance for electric currents and reduces the risk of electric shock. This tool is equipped with an electrical cord that has an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching receptacle that is prope ...

  • Craftsman 137.24885 - page 6

    RECOMMENDED ACCESSORIES WARNING I Visit your Sears Hardware Department or see the Craftsman Power and Hand Tools Catalog to purchase recommended accessories for this power tool. [A WARNING I To avoid the risk of personal injury: • Do not use adjustable (wobble) type dadoes or carbide tipped dado blades. = Only use atackable dadoes. • Maximum da ...

  • Craftsman 137.24885 - page 7

    UNPACKING YOUR TABLE SAW A C B l .... J, Jl_ 1 D J K L M N 0 P R T ...

  • Craftsman 137.24885 - page 8

    Blade guard Table insert Miter gauge X fence Side table extension wing Extension wing locking lever Blade tilt scale Blade tilt pointer Overload reset switch ON/OFF switch with safety key Rip fence andmiter gauge storage Bevel tilting handwheel Blade bevel lock knob Blade elevation handwheel Tools storage ...

  • Craftsman 137.24885 - page 9

    ANTFKICKBACK PAWLS - Prevents the workpiece from being kicked upward or back toward the front of the table saw by the spinning blade. OVERLOAD RESET SWITCH - Resets the thermocouple andprovides a way to restart the saw motor if it overloads or overheats. ARBOR - The shaft on which the blade or dado is mounted. PUSH STICK- Used to push workpieces wh ...

  • Craftsman 137.24885 - page 10

    ASSEMBUNG STAND (FIG. A) 1. Unpack all parts and group by type and size. Refer to the parts list forcorrect quantities. 2. Attach the stand door (3) to the front of the stand base (5) using three screws M5"12-12 (4). 3. Attach the floor plate (1) to the stand (5) using ten screws M5"12-12 (2). See PARTS LIST AND SCHEMATIC FOR STAND SECTIO ...

  • Craftsman 137.24885 - page 11

    MOUNT SAW ONWORK SURFACE 1. tf the stand will not be used, the saw must be properly secured to a sturdy workbench using the four mounting holes at the base of the saw. 2. Square the saw on the mounting surface andmark the location of the four 3/8 in. mounting holes. 3. Drill the four 3/8 in.holes into the mounting surface. 4. Place the saw on the w ...

  • Craftsman 137.24885 - page 12

    2. Raise the blade arbor (4-Fig. F) to the maximum height by turning the blade raising handwheel counterclockwise. 3. Place the open-end wrench (8) jaws on the flats of the saw arbor to keep the arbor from turning (Fig. G) andplace the box-end wrench (9) on the arbor nut (5),and turn counterclockwise. 4. Remove the arbor nut (5)and outer flange (6- ...

  • Craftsman 137.24885 - page 13

    7. When the splitter is properly aligned withthe saw blade, tighten the bolt securely. NOTE: The splitter bracket must always be correctly aligned so the cut workpiece will pass on either side without binding or twisting, [A WARNINa I See Fig. I-1 flat washer (11) must be under knob (12). NOTE: Be sure to tighten knob very tight and periodically ch ...

  • Craftsman 137.24885 - page 14

    INSTALLING REAR TABLE EXTENSION (FIG, M) 1. Place the rear table extension onto the two rear table extension tubes (1). 2. Snap two long location seats (2) over the two rear table extension tubes (1). Make sure the locating pin in the location seat fits into the matching hole (3) in the extension tube. 3. Insert rear table extension tubes (1) into ...

  • Craftsman 137.24885 - page 15

    90 ° (0 °) Stop 1. Disconnect the saw from the power source. 2. Turn the blade elevation handwheel and raise the blade to the maximum elevation. 3. Loosen the blade bevel lock knob (1) andmove the blade to the maximum vertical position, thentighten the lock knob (1). 4. Place a combination square on the table andagainst the blade (2) to determine ...

  • Craftsman 137.24885 - page 16

    7. Rotate the blade bringing the marked tooth to the rear andabout Yz in. above the blade. 8. Carefully slide the combination square to the rear until the ruler touches the marked tooth. 9. tf the ruler touches the marked tooth at the front and rear position, no adjustment is needed at this time. tf not or the base of the rule is no longer parallel ...

  • Craftsman 137.24885 - page 17

    BASIC SAW OPERATIONS RAISE THE BLADE (FIG. U) To raise or lower the blade, turn the blade elevation handwheel (1) to the desired blade height, and then tighten lock handle (2) to maintain the desired blade angle. Fig. U TiLTiNG THE BLADE (FIG. U) 1. To tilt the saw blade for bevel cutting, loosen the bevel lock knob (2) and turn the tilting handwhe ...

  • Craftsman 137.24885 - page 18

    USING THE DUST CHUTE (FIG. Y) I A WARNING I To prevent fire hazard, clean and remove sawdust from under the saw frequently. To prevent sawdust buildup inside the saw housing, attach a vacuum hose (1) to the dust chute (2) at the rear of the table saw. Do not operate the saw with the hose in place unless the vacuum is turned on. Fig. Y CUTTING OPERA ...

  • Craftsman 137.24885 - page 19

    [_, WARNING I Never attempt to pull the workpiece backwards during a cutting operation, This will cause kickback and serious injury to the user can occur, When the blade completely stops raise the anti-kickback pawls (4) on each side of the splitter and slide the workpiece out, Fig, BB 4 1 BEVEL RIPPING This cut is the same as a rip cut except the ...

  • Craftsman 137.24885 - page 20

    1. Adjust the blade (1) to the desired angle, and tighten the blade bevel lock knob. 2. Tighten miter lock handle (2) at 90 ° . 3. Hold workpiece firmly against the face of the miter gauge throughout the cutting operation. Fig, DD COMPOUND MITER CROSSCUTTING (FIG. EL) 0o-45 ° BLADE BEVEL & 0o-45 ° MITER ANGLE This sawing operation is combini ...

  • Craftsman 137.24885 - page 21

    DADO CUTS (FIG. HH) • Only Stackable dado blades can be used on this saw. • DO NOT use Adjustable or Wobble type dadoes. • Maximum dado cut width is Y2 in. 1. A dado table insert must be purchased separately for this saw to accept a dado blade. Remove saw blade and blade guard for dado cuts ONLY. Reinstall and realign blade guard for all thro ...

  • Craftsman 137.24885 - page 22

    MAiNTAiNING YOUR TABLE SAW GENERAL MAINTENANCE [A WARNING I Before maintaining or lubricating the saw, turn switch off, remove the switch key, and unplug the SaW. 1. Clean out all sawdust that has accumulated inside the saw cabinet and the motor. 2. Polish the saw table with an automotive wax to keep it clean and to make it easier to slide the work ...

  • Craftsman 137.24885 - page 23

    [A WARNINO I To avoid injury from an accidental start, turn the switch OFF remove the switch key and always remove the plug from the power source before making any adjustments, = If for any reason the motor will not run, contact Sears Service Center at f =800=4-MY=HOME®, SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION Saw will not start. 1. Saw not plug ...

  • Craftsman 137.24885 - page 24

    10 in. TABLE SAW MODEL NO. 137.248850 [A WARNING I When servicing use only CRAFTSMAN replacement parts, Use of any other parts many create a HAZARD or cause product damage, Any attempt to repair or replace electrical parts on this Table Saw may create a HAZARD unless repair is done by a qualified service technician. Repair service is available at y ...

  • Craftsman 137.24885 - page 25

    10 in. TABLE SAW MODEL NO. 137.248850 / SCHEMATIC / 2EST 2ET4 2ET2 2ETJ 2ETV / / ,0J76 / ODPA 2GRU < /ZGKE 0JED _KOZ4 0BAU / _0KMR -- / OKRX OKSG ...

  • Craftsman 137.24885 - page 26

    10 in. TABLE SAW MODEL NO. 137.248850 PARTS LiST AND SCHEMATIC FOR MOTOR I.D. Descirpfion 0HV8 BALL BEARING 0HVU BALL BEARING 0HX9 NEEDLE BEARING 0JAL EXT.TOOTH LOCK WASHER 0JX3 HEX. SOC. SET SCREW 0K3A CR.RE. PAN HD. SCREW & WASHER 0K5V CR.-RE. COUND.HD.SCREW 0KCP CR.RE. PAN HEAD TAPPING & WASHER SCREW 0KTH STRAIN RELIEF 0QEC ARBOR SHAFT A ...

  • Craftsman 137.24885 - page 27

    10 in. TABLE SAW MODEL NO. 137.248850 PARTS LiST AND SCHEMATIC FOR STAND LB. 0J68 0K82 0KB3 0KBA 0KMS 0KMY 0KRL 0VJX 27CC 2ETN 2ETP 2ETQ 2ETR 2ETS 2ETT 2EU3 2EU4 2EW0 2FS2 2FYJ 2FYK 2FYL 2FYN Description SIZE FLAT WASHER cp5 _10-1 CR. RE. COUNT HD. TAPPING SCREW M5"12-16 CR. RE. PAN HD. TAPPING SCREW M4"18-8 CR. RE. PAN HD. TAPPING SCREW ...

  • Craftsman 137.24885 - page 28

    PUSH STICK CONSTRUCTION This is a full-size drawing (actual size) Use good quality plywood or solid wood Use 1/2 in. or 3/4 in. material Push stick MUST be thinner than the width of material being cut / Z / / Drill Hole For Hanging / / Notch To Prevent Hand From Slipping Cut Here To Push 1/2 in. Wood Cut Here To Push 3/4 in. Wood r ...

  • Craftsman 137.24885 - page 29

    ...

  • Craftsman 137.24885 - page 30

    Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold itt For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage do ...

Manufacturer Craftsman Category Saw

Documents that we receive from a manufacturer of a Craftsman 137.24885 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 137.24885 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 137.24885
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 137.24885.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 137.24885, service manual, brief instructions and user manuals Craftsman 137.24885. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 137.24885.

Similar manuals

A complete manual for the device Craftsman 137.24885, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 137.24885 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 137.24885.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 137.24885 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 137.24885, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 137.24885, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 137.24885 - which should help us in our first steps of using Craftsman 137.24885
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 137.24885
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 137.24885 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 137.24885?

Use the form below

If you did not solve your problem by using a manual Craftsman 137.24885, ask a question using the form below. If a user had a similar problem with Craftsman 137.24885 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)