Manual Hunter Fan R410A

48 pages 3.34 mb
Download

Go to site of 48

Summary
  • Hunter Fan R410A - page 1

    S S E E R R V V I I C C E E M M A A N N U U A A L L F F D D A A S S e e r r i i e e s s S S p p l l i i t t S S y y s s t t e e m m s s F F D D A A S S e e r r i i e e s s M M u u l l t t i i S S y y s s t t e e m m s s ...

  • Hunter Fan R410A - page 2

    ...

  • Hunter Fan R410A - page 3

    MITSUBISHI HEAVY INDUSTRIES - PAC SERVICE MANUAL INDEX MAINTENANCE DATA 2 ERROR CODES 4 PCB INDOOR UNITS 8 ERROR DISPLAY & REMEDY CHART 12 PCB OUTDOOR UNITS 22 ERROR DISPLAY – OUTDOOR UNIT 25 OPERATIONAL DATA CHECK – WIRED CONTROLLER 35 REMOTE CONTROL – WIRED 36 - SETTING FUNCTIONS 37 ERROR DISPLAY – WIRELESS CONTROL 43 REMOTE CONTROL W ...

  • Hunter Fan R410A - page 4

    - 2 - 1. MAINTENANCE D A T A 1. 1 Servicing (1) Evacuation The ev acuation is a procedure to purge impurities, such as noncondensable gas, air , moisture from the refrigerant equipment by using a vacuum pump. Since the refrigerant R410A is v ery insoluble in water , ev en a small amount of moisture left in the refrig er- ant equipment will freeze, ...

  • Hunter Fan R410A - page 5

    - 3 - (2) Refrigerant charging (a) After the ev acuation shown in the abo ve, change the connection of the charge hose A to the refrigerant cylinder . (b) Purge air from the char ge hose A . First loosen the connecting portion of the charge hose at the gaug e manifold side and open valve 3 for a fe w seconds, and then immediately retighten it after ...

  • Hunter Fan R410A - page 6

    - 4 - (1) Selfdiagnosis function (a) Check Indicator T able Whether a failure exists or not on the indoor unit and outdoor unit can be know by the contents of remote controller eroor code , indoor/outdoor unit green LED (power pilot lamp and microcomputer normality pilot lamp) or red LED (check pilot lamp). 1) Indoor unit side Outdoor unit LED Indo ...

  • Hunter Fan R410A - page 7

    - 5 - Outdoor unit LED Indoor unit LED Green Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Keeps flashing Red Green Stays OFF Stays OFF Stays ...

  • Hunter Fan R410A - page 8

    - 6 - Section Display section Error code of remote controller Inspection LED (red) of indoor unit PCB Inspection LED (red) of outdoor unit PCB • Displays the error of higher priority (When plural errors are persisting) • Displays the present errors. (When a new error has occurred after the former error w as reset.) Error detail Error code T imi ...

  • Hunter Fan R410A - page 9

    - 7 - 4) Recording and reset of error Notes (1) Priority is in the order of E1 > ... > E10 > ... > E60. (2) Procedures of trouble diagnosis When any error occurs, inspect in following sequence. Detailed explanation on each step is given later in this text. Note (1) It means the operation to turn of f the power and back on again more tha ...

  • Hunter Fan R410A - page 10

    - 8 - CNM3 52X6 52X1 52X2 52X3 52X4 52X8-2 PC3 IC2 C2 X1 CNE F2 F1 Z2D Z3D Z4D Z5D R16 ZD1 CNJ D2 IC7 TVS1 CNM2 CNW8 CNT IC9 J8 1234 J10 J11 J12 CNR IC12 CNG LED2 LED1 CNW9 C13 PC5 C12 C1 L1 C58 IC3 C4 C3 CNY CNI CNH CNN1 SW2 SW10 SW5 1234 SW7 J5 J6 J7 J8 SW8 J1 J2 J3 J4 SW9 IC11 IC8 CNB C11 C41 KN1 CNV 52X7 52X8-1 CNW7 TM1 PC2 PC1 R17 C23 L2 ON ON ...

  • Hunter Fan R410A - page 11

    - 9 - CNW1 CNJ2 CNM3 CNR CNV LED1 LED2 CNB CNW2 KN1 52X5 52X3 52X2 52X2 52X6 52X4 52X8-2 52X8-1 52X7 L3 F1 ZNR CNW0 CNM1 L2 L1 C57 CNQ CNT CNH CNN1 SW2 SW5 CNE SW8 SW7 SW9 SW10 IC8 IC7 PCB power supply connector (Primary side) PCB power supply connector Heat exchanger thermistor, Return air thermistor (Thl-R1, Thl-A) DIP switch (SW5) J5, J6 (SW8) J ...

  • Hunter Fan R410A - page 12

    - 1 0 - Heat exchanger thermistor (Thl-R2) Remote controller PCB power supply connector (Primary side) PCB power supply connector (Secondary side) Fan motor Connector (CNT) Louver motor J31 CNZ SW10 SW5 SW9 SW7 SW8 SW2 J9 J10 J11 J5 J6 J7 J8 J1 J2 J3 J4 CNE IC9 IC10 LED1 CNL C92 CNG CNY CNJ CNT IC8 R62 BZ L4 C2 CNM C104 R151 CNW1 IC11 L1 L2 CNH CNN ...

  • Hunter Fan R410A - page 13

    - 1 1 - CNT CNV CNO CNH CNF CNB CNQ CNN1 CNN2 SW2 SW10 SW5 SW7 SW9 SW8 CNZ CNI CNO CNA F3 F2 CNK2 CNK1 CNW2 CNG CNE CNW0 CNW1 CNM3 52X3 52X5 52X4 52X2 52X1 52X6 L3 L2 L1 L4 CNJ2 CNR F1 LED1 LED2 PCB power supply connector (Primary side) PCB power supply connector (Secondary side) Heat exchanger thermistor (Thl-R2) Address swith (SW2) DIP switch (SW ...

  • Hunter Fan R410A - page 14

    - 1 2 - 1 Error display : No display LCD display : No display [Power supply line error] Indoor unit Red LED Green LED Stays OFF Stays OFF Red LED Green LED Stays OFF Stays OFF Outdoor unit YES YES YES YES YES NO (1)(2) (1)(2) NO YES NO YES NO NO NO NO NO YES Fuse OK? Several 10K Ω or higher. Is the voltage between 1 and 2/N of the indoor unit ’ ...

  • Hunter Fan R410A - page 15

    - 13 - Indoor unit Green LED Red LED 3 time flash Keeps flashing Outdoor unit Green LED Red LED Stays OFF Keeps flashing OK Remote controller wiring connect check (Red · White · Black) Remote controller wire is removed NO Correction NO Approximately 10 ~ 11 V between X and Z. YES Note (1) Z is GND. Note (2) 3 is GND. (2) (1) Power supply reset Ma ...

  • Hunter Fan R410A - page 16

    - 14 - 2 Error displa y “ W AIT ” Indoor – outdoor communications trouble (Initial (when the power is turned on) Indoor unit Red LED Green LED Stays OFF Keeps flashing 2 time flash Keeps flashing Red LED Green LED Outdoor unit If trouble occurs during communications, the error code E5 is displayed (Outdoor , Red LED flashes 2 times). The chec ...

  • Hunter Fan R410A - page 17

    - 1 5 - 3 Error display : e1 [Communication error between remote controller~Indoor unit] Indoor unit Red LED Green LED Stays OFF Keeps flashing Stays OFF Keeps flashing Red LED Green LED Outdoor unit Voltage between X and Z approximately 10~11 V? YES NO Replacement remote controller Voltage fluctuates between 5~11 V between Y and Z. Is the resistan ...

  • Hunter Fan R410A - page 18

    - 1 6 - 4 Error display : e6 [Defective indoor unit heat exchanger thermistor] 5 Error display : e7 [Detective return air thermistor] Indoor unit Red LED Green LED 1 time flash Keeps flashing Red LED Green LED Stays OFF Keeps flashing Outdoor unit Indoor unit Red LED Green LED 1 time flash Keeps flashing Red LED Green LED Stays OFF Keeps flashing O ...

  • Hunter Fan R410A - page 19

    - 1 7 - 7 Error display : e9 [Drain trouble] Indoor unit Red LED Green LED 1 time flash Keeps flashing Red LED Green LED Stays OFF Keeps flashing Outdoor unit Correction Replacement indoor unit control PCB Replacement indoor unit PCB YES NO NO NO NO Is there any overflow? DM operation DC 12 V at both terminals of CNI? YES NO Abnormal data check in ...

  • Hunter Fan R410A - page 20

    - 1 8 - 8 Error display : e10 [Control of 1 remote controller VS multiple units Excessive number of units (more than 17 units) ] Indoor unit Red LED Green LED Stays OFF Keeps flashing Red LED Green LED Stays OFF Keeps flashing Outdoor unit Are more than 17 units connected to a remote controller? Reduce to 16 units or less YES NO Defective indoor un ...

  • Hunter Fan R410A - page 21

    - 1 9 - NO NO Abnormal data check with remote controller After check reset, fan runs on Me. Check the circumstances. Was it reproduced? Fan ON? NO NO NO NO NO NO YES YES YES YES YES YES YES YES When the motor is turning, does the voltage at CNM 6 (Blue) fluctuate between DC 0 ~ 15 V? Secondary side of transformer (red-red) 14V or more Does the fan ...

  • Hunter Fan R410A - page 22

    - 20 - 10 Error display : e28 [Directive remote controller thermistor .] Indoor unit Red LED Green LED Stays OFF Keeps flashing Red LED Green LED Stays OFF Keeps flashing Outdoor unit Detectivie remote controller PCB Replacement (Detective re- mote thermistor input circuit) YES NO NO YES Detective remote controller thermistor Replacement Are charac ...

  • Hunter Fan R410A - page 23

    - 21 - (4) Error diagnosis procedures at the outdoor units side At the error diagnosis related to the outdoor unit, check at first the error code of remote controller and the illumination patterns of norma1 and inspection display lamps in the same manner as the case of indoor unit. Then estimate the outline, the cause and the location of error base ...

  • Hunter Fan R410A - page 24

    - 22 - W CNI F2 T8 CN CNQ CNE CNI3 CNW CNI2 CNV1 CNM F3 T1 T5 T4 T2 F1 CNL CNTR SW6 SW7 T7 T6 V U Outdoor air temp. thermistor, Outdoor heat exchanger themistor, Discharge pipe thermistor (Tho-A, Tho-R, Tho-D) DIP switch (SW7) Fan motor Reactor Stepping motor Power transistor thermistor (Tho-IPM) DIP switch (SW6) Sub PCB (Noise filter) ● Function ...

  • Hunter Fan R410A - page 25

    - 23 - C6 C5 L6 L5 C7 C13 IC12 L7 C6 C8 L8 L10 C9 C10 SW6 SW2 KN1 CNM1 CNE CNA2 X04 X03 X02 X07 X05 X01 X06 CNM2 CNM3 CNS CNO CNR CNP3 CNP1 CNP2 CNA1 CNV1 CNW C3 KN2 CNM4 LED-R LED-G SW4 SW5 L11 L12 CNQ CT2 CT1 J4 J3 J2 J1 J8 J7 J6 J5 1234 C12 C11 C4 C1 C2 HT1 SW3 J14 J13 J12 J11 J15 J16 CNL SW3 SW6 SW5 SW4 SW2 (T est run operation switch) Fan moto ...

  • Hunter Fan R410A - page 26

    - 24 - L N E TB TB Red White Y/NG LED1 Red T1 T5 Red White Black Orange Y ellow UV W T6 T7 T8 CM F2 (250V 20A) CnTR Control PCB Power transistor module CNI3 T2 T4 6 DC280V F3 (250V 1A) F5 ( 20A ) 4 3 2 1 CNI2 FM 0 T21 T22 Sub PCB (Noise filter) T24 T25 T26 T30 T27 T28 CNI1 Orange Gray T o indoor unit Brown Temperature [ T ] ( ˚C ) T < 80˚C T & ...

  • Hunter Fan R410A - page 27

    - 25 - 1 Error display : e5 [Communications error during operation] Indoor unit Red LED Green LED 2 time flash Keeps flashing Red LED Green LED 2 time flash Keeps flashing Outdoor unit Is the connection of the signal wires at the outdoor unit poor? Is the connection of the signal wires at the indoor unit poor? Did the remote controller’s LCD retu ...

  • Hunter Fan R410A - page 28

    - 26 - 3 Error display : e33 [Inverter primary current abnormal] [Only case of 151~251 type] Indoor unit Red LED Green LED Stays OFF Keeps flashing Red LED 1 time flash Outdoor unit YES YES YES NO NO NO Is the power supply normal? Restore it to the normal state. Restore it to the normal state. Remove any foreign matter such as dust or dirt. Replace ...

  • Hunter Fan R410A - page 29

    - 27 - 4 [Open phase at L3 phase of 52C secondary side] (Only case of 301~601 type) Indoor unit Red LED Green LED Stays OFF Keeps flashing Red LED Green LED 1 time flash Keeps flashing Outdoor unit AAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAA AAA 52C secondary side L3 phase open? Repair YES NO The outdoor unit control PCB is faulty. (The C ...

  • Hunter Fan R410A - page 30

    - 28 - 7 [Defective outdoor unit heat exchanger thermistor] Indoor unit Red LED Green LED Stays OFF Keeps flashing Red LED Green LED 1 time flash Keeps flashing Outdoor unit Temperature ( ° C) 15 10 5 01 0 3 0 4 0 20 50 5k Ω at 25 ° C Is the outdoor unit heat exchanger thermistor connector OK? Repair NO YES NO YES Are the outdoor unit heat exch ...

  • Hunter Fan R410A - page 31

    - 29 - 300 400 200 100 0 30 40 20 10 0 - - -50 05 0 Temperature [T]( ° C) T < 0 ° C T > 0 ° C Is the outdoor air temperature thermistor connector connection OK? Repair NO NO YES YES Is the outdoor air temperature thermistor characteristics OK, is there no broken wire? Defective outdoor air temperature thermistor Replacement Defective outdo ...

  • Hunter Fan R410A - page 32

    - 30 - Error display : e40 Is the power supply voltage proper? • Is the installation space for the indoor and outdoor units proper? • Is there a short circuit in the indoor or outdoor units? • During cooling: Is FMo operating? Is the service valve fully open? • During heating: Is FMI operating? Is the service valve fully open? Is the filter ...

  • Hunter Fan R410A - page 33

    - 31 - 12 Error display : e47 [Inverter over-voltage trouble] (Only case of 151~251 type) Indoor unit Red LED Green LED Stays OFF Keeps flashing Red LED 1 time flash Outdoor unit NO YES YES Remove the foreign matter such as dust and dirt. Replace Is the fuse (F1: 250V, 20A) blown? Is there foreign matter such as dust or dirt on the soldered surface ...

  • Hunter Fan R410A - page 34

    - 32 - 15 [P ower transistor thermistor faulty .] (Only case of 151~251 type) Indoor unit Red LED Green LED Stays OFF Keeps flashing Red LED 1 time flash Outdoor unit Temperature [T] ( ° C) T < 80 ° C T > 80 ° C 100 50 0 10 5 0 05 0 20 80 100 120 Is the power transistor thermistor connector connection OK? NO YES Repair Are the power transi ...

  • Hunter Fan R410A - page 35

    - 33 - Indoor unit Red LED Green LED Stays OFF Keeps flashing Red LED 1 time, 2 time, 3 time flash Outdoor unit NO NO NO NG YES Check of power supply Replacement compressor Replacement compressor OK Check the refrigerant level and refrigerant circuit. Inverter NG Inverter OK Check the compressor ’ s insulation resistance and winding resistance. C ...

  • Hunter Fan R410A - page 36

    - 34 - Compressor operation Replacement control PCB Normal NO NO NO YES YES YES Is the power transistor module cracked or burnt? Is there a short circuit between the power transistor module terminals? ❇ 1 Is the balance between the compressor current phases good? If there is a 10% or greater difference in the current in different phases. (except ...

  • Hunter Fan R410A - page 37

    - 35 - ( 4 ) Check abnormal operation data with the remote controller Operation data are recorded when there is an abnormal state and these data can be displayed in the remote controller by operating the remote controller buttons. (1) Press the CHECK button. The display will change from “ FUNCTION ” → “ SET ” → “ OPERA TION DA T A ” ...

  • Hunter Fan R410A - page 38

    - 36 - 2 OUTLINE OF OPERA TION CONTR OL BY MICR OCOMPUTER (1) Remote controller (a) Wired remote controller The figure belo w shows the remote controller with the co ver opened. Note that all the items that may be displayed in the liquid crystal display area are sho wn in the figure for the sake of explana tion. Characters displayed with dots in th ...

  • Hunter Fan R410A - page 39

    - 37 - ( 2 ) Setting functions using the remote controller (a) The factory settings of this unit's functions are as follows: If you want to char g e a setting, follo w the procedure f ound in the installation manual and set to y our desired setting. For the method of setting, please refer to the installation manual of a remote contr ol unit. 1 ...

  • Hunter Fan R410A - page 40

    - 38 - (b) Function setting method 1) Stop the air conditioner 2) Press the SET and MODE buttons simultaneously for 3 seconds or longer . The screen display will be switched as follo ws: “ SELECT ITEM” “ SET" “FUNCTION SET ” 3) Press the SET button. The unit will enter the function setting mode. The screen display will charge to “ ...

  • Hunter Fan R410A - page 41

    - 39 - When “ I/U FUNCTION ” is selected. 1 The screen display will be switched as follo ws: “ I/U SELECT ” “ SET ” “ I/U No.00 ” (blinking) 2 Press either or button. Select the indoor unit number that you want to change settings. If onl y one indoor unit is connected, the indoor unit number will not char ge, so please proceed to St ...

  • Hunter Fan R410A - page 42

    - 40 - 12 Function No. A (Example) If the upper limit is set at 28˚C Function Contents B Setting Contents C TEMP RANGE SET DISP CHANGE NO DISP CHANGE Control Contents The remote controller’s display and sent data upper limit changes to 28 ° C. The remote controller’s display upper limit remains at 30ºC and only the upper limit of the sent da ...

  • Hunter Fan R410A - page 43

    - 41 - ( 3 ) Cooling T est Operation Procedure Carry out the following test operation procedure using the remote controller . (a) Starting the Cooling T est Operation 1 Press the ON/OFF button to start operation. 2 Press the MODE button and select “ COOL. ” 3 Press the TEST b utton continuously for 3 seconds or longer . The display changes from ...

  • Hunter Fan R410A - page 44

    - 42 - Cooling Heating Gas operation valve charge port Suction pressure (low pressure) Discharge pressure (high pressure) Check joint in the unit Discharge pressure (high pressure) Suction pressure (low pressure) ( 5 ) T est run (a) T est run method 1) A test run can be initiated from an outdoor unit by using SW9 (SW2) and SW5-4 for on-site setting ...

  • Hunter Fan R410A - page 45

    - 4 3 - Romote controller signal receiving part Backup switch Check monitor (Error code display E1~E60) Operation display light (Green) • Lights continously: Under air conditioner operaton • Keeps flashing: Under heating preparation (At the time of heating operation) • 3 time flash: Under reception of a remote controller signal T imer/Check d ...

  • Hunter Fan R410A - page 46

    - 4 4 - MODE TEMP ON/OFF AIR FLOW FILTER FAN SPEED SET TIME ACL TIMER AUTO COOL DRY FAN HEAT FIL TER ° C AM PM ON AM PM OFF FAN HI ME LO ( c ) Wireless remote controller OPERA TION MODE indicator Indicates selected operation mode Fan speed Indicates the selected fan speed Timer ON time Indicates the timer ON time. When the timer mode is “CONT” ...

  • Hunter Fan R410A - page 47

    ...

  • Hunter Fan R410A - page 48

    NOTICE The installation of this equipment must comply with all NATIONAL, STATE and LOCAL CODES . This Service Guide does not cover all installation circumstances and is meant for guidance only and therefore will not form part of any legally binding contract. An installation guide is provided with the air conditioning equipment. CE These Air Conditi ...

Manufacturer Hunter Fan Category Air Conditioner

Documents that we receive from a manufacturer of a Hunter Fan R410A can be divided into several groups. They are, among others:
- Hunter Fan technical drawings
- R410A manuals
- Hunter Fan product data sheets
- information booklets
- or energy labels Hunter Fan R410A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hunter Fan R410A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hunter Fan R410A, service manual, brief instructions and user manuals Hunter Fan R410A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hunter Fan R410A.

Similar manuals

A complete manual for the device Hunter Fan R410A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hunter Fan R410A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hunter Fan R410A.

A complete Hunter Fan manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hunter Fan R410A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hunter Fan R410A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hunter Fan R410A, that we can find in the current document
3. Tips how to use the basic functions of the device Hunter Fan R410A - which should help us in our first steps of using Hunter Fan R410A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hunter Fan R410A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hunter Fan R410A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hunter Fan R410A?

Use the form below

If you did not solve your problem by using a manual Hunter Fan R410A, ask a question using the form below. If a user had a similar problem with Hunter Fan R410A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)