Manual Chamberlain WD822KS 1/2 HP

40 pages 2.49 mb
Download

Go to site of 40

Summary
  • Chamberlain WD822KS 1/2 HP - page 1

    Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless The Protector System ® is connected and properly aligned. ■ Periodic checks of the opener are required to ensure safe operation. ■ The model number label is ...

  • Chamberlain WD822KS 1/2 HP - page 2

    2 T ABLE OF CONTENTS When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully . When you see this Signal Wor ...

  • Chamberlain WD822KS 1/2 HP - page 3

    3 T o prevent damage to garage door and opener: • AL W A YS disable locks BEFORE installing and operating the opener . • ONL Y operate garage door opener at 120V , 60 Hz to avoid malfunction and damage. T o prevent possible SERIOUS INJUR Y or DEA TH: • AL W A YS call a trained door systems technician if garage door binds, sticks, or is out of ...

  • Chamberlain WD822KS 1/2 HP - page 4

    4 Safety Reversing Sensor Header Wall Access Door Safety Reversing Sensor Gap between floor and bottom of door must not exceed 1/4" (6 mm). Extension Spring Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 23 for details. Support bracket & fas ...

  • Chamberlain WD822KS 1/2 HP - page 5

    5 Access Door Safety Reversing Sensor Safety Reversing Sensor Gap between floor and bottom of door must not exceed 1/4" (6 mm). Garage Door Header Wall Header Bracket Door Bracket Straight Door Arm Curved Door Arm Trolley Emergency Release Rope & Handle Rail Belt Trolley Stop Bolt CLOSED POSITION Planning (Continued) ONE-PIECE DOOR INST AL ...

  • Chamberlain WD822KS 1/2 HP - page 6

    6 SECURITY ✚ 3-Button Remote Control Belt Curved Door Arm Section Safety Labels and Literature Straight Door Arm Section Hanging Brackets Multi-Function Door Control Panel Belt Cap Retainer SECURITY ✚ Keyless Entry Door Bracket L O C K LIGHT (2) Safety Reversing Sensors (1 Sending Eye and 1 Receiving Eye) with 2-Conductor White & White/Blac ...

  • Chamberlain WD822KS 1/2 HP - page 7

    7 Master Link (2) Idler Bolt (1) Nut 3/8" (1) Trolley Threaded Shaft (1) Bolt 1/4"-20x1-3/4" (2) Lock Washer 3/8" (1) Lock Nut 1/4"-20 (2) Spacer (2) Wing Nut 1/4"-20 (2) Carriage Bolt 1/4"-20x1/2" (2) Handle Nut 5/16"-18 (8) Ring Fastener (3) Insulated Staples (30) Drywall Anchors (2) Clevis Pin 5/16&qu ...

  • Chamberlain WD822KS 1/2 HP - page 8

    Clip Tapered End of Rail FRONT RAIL (TOP) KEEP LARGER HOLE ON TOP 8 ASSEMBL Y STEP 1 Assemble the Rail & Install the T rolley T o avoid installation difficulties, do not run the garage door opener until instructed to do so. 8" (20 cm) Distance from Idler Pulley Hole Front Rail (TO DOOR) Window Cut-Out Locking Pliers Idler Pulley Hole Tabs ...

  • Chamberlain WD822KS 1/2 HP - page 9

    9 T o avoid SERIOUS damage to garage door opener , use ONL Y those bolts/fasteners mounted in the top of the opener . ASSEMBL Y STEP 2 Fasten the Rail to the Motor Unit • Insert a 1/4"-20x1-3/4 bolt into the cover protection bolt hole on the back end of the rail as shown. T ighten securely with a 1/4"-20 lock nut. Do NOT overtighten. ? ...

  • Chamberlain WD822KS 1/2 HP - page 10

    ASSEMBL Y STEP 4 Install the Belt and Attach the Belt Cap Retainer 1. Pull the belt around the idler pulley and toward the trolley . The ribbed side must contact the pulley . 2. Hook the trolley connector into the retaining slot on the trolley as shown. 3. With the trolley against the pliers, dispense the remainder of the belt along the rail length ...

  • Chamberlain WD822KS 1/2 HP - page 11

    11 INST ALLA TION ASSEMBL Y STEP 5 Set the T ension • Insert a screwdriver tip into one of the nut ring slots and brace it firmly against the trolley . • Place a 7/16" open end wrench on the square end. Rotate the nut about 1/4 turn until the spring releases and snaps the nut ring against the trolley . This sets the spring to optimum belt ...

  • Chamberlain WD822KS 1/2 HP - page 12

    12 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header wall above the door . Y ou can fasten the header bracket with ...

  • Chamberlain WD822KS 1/2 HP - page 13

    13 Lag Screws 5/16"x9x1-5/8" — Finished Ceiling — Door Spring Header Wall UP Ceiling Mounting Holes 6" (15 cm) Maximum Header Bracket Vertical Centerline of Garage Door Garage Door Vertical Centerline of Garage Door INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the ga ...

  • Chamberlain WD822KS 1/2 HP - page 14

    14 INST ALLA TION STEP 3 Attach the Rail to the Header Bracket NOTE: (Optional) With some existing installations, you may re-use the old header bracket with the two plastic spacers included in the hardware bag. Place the spacers inside the bracket on each side of the rail, as illustrated. • Position the opener on the garage floor below the header ...

  • Chamberlain WD822KS 1/2 HP - page 15

    15 ONE-PIECE DOOR WITHOUT TRACK A 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder . Y ou will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 on its side on the top section of the door beneath the rail. ...

  • Chamberlain WD822KS 1/2 HP - page 16

    16 INST ALLA TION STEP 5 Hang the Opener Three representative installations are shown. Y ours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural supports before installing the opener . This bracket and fastening hardware a ...

  • Chamberlain WD822KS 1/2 HP - page 17

    17 T o prevent possible SERIOUS INJUR Y or DEA TH from electrocution: • Be sure power is not connected BEFORE installing door control. • Connect ONL Y to 24 VOL T low voltage wires. T o prevent possible SERIOUS INJUR Y or DEA TH from a closing garage door: • Install door control within sight of garage door , out of reach of children at a mini ...

  • Chamberlain WD822KS 1/2 HP - page 18

    18 INST ALLA TION STEP 7 Install the Lights • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in each socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes when pow ...

  • Chamberlain WD822KS 1/2 HP - page 19

    19 INST ALLA TION STEP 9 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, co ...

  • Chamberlain WD822KS 1/2 HP - page 20

    20 Invisible Light Beam Protection Area Sensor Beam 6" (15 cm) max. above floor Sensor Beam 6" (15 cm) max. above floor Facing the door from inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direct ...

  • Chamberlain WD822KS 1/2 HP - page 21

    21 DOOR TRACK MOUNT (RIGHT SIDE) Indicator Light Lens Lip Sensor Bracket Door Track FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) Indicator Light Sensor Bracket Lens Extension Bracket (See Accessories) Inside G arage W all (Provided with Extension Bracket) (Provided with Extension Bracket) Figure 1 Figure 2 Figure 3 Figure 4 WALL MOUNT (RIGHT SI ...

  • Chamberlain WD822KS 1/2 HP - page 22

    22 Carriage Bolt 1/4"-20x1/2" Lens Wing Nut Figure 5 MOUNTING AND WIRING THE SAFETY SENSORS • Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor . Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door . Be sure the lens is not obstructed by a bracket extension (Fi ...

  • Chamberlain WD822KS 1/2 HP - page 23

    23 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. WARN ING CAUTION WARN ING WARN ING INST ALLA TION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following p ...

  • Chamberlain WD822KS 1/2 HP - page 24

    24 Header Wall Vertical Centerline of Garage Door Finished Ceiling Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 Support For a door with no exposed framing, or for the optional installation, use lag screws 5/16"x1-1/2" (Not Provided) to fasten door bracket. MET AL DOOR Top of Door (Inside Garage) Door Bracket Optional ...

  • Chamberlain WD822KS 1/2 HP - page 25

    25 INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back (away from t ...

  • Chamberlain WD822KS 1/2 HP - page 26

    26 ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin. • Secure with a ring fastener . 2. Adj ...

  • Chamberlain WD822KS 1/2 HP - page 27

    27 ADJUSTMENT STEP 1 Adjust the UP and DOWN T ravel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. T o operate the opener , press the Door Control push bar . Run the opener through a complete travel cycle. • Does the door open and close completely? • Does the door stay closed and not rev ...

  • Chamberlain WD822KS 1/2 HP - page 28

    28 ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the right panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door . If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weat ...

  • Chamberlain WD822KS 1/2 HP - page 29

    29 Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Safety reversal system MUST be tested ever y month. • If one control (force or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made ...

  • Chamberlain WD822KS 1/2 HP - page 30

    30 OPERA TION Using Y our Garage Door Opener Y our Security ✚ ® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with up to eight Security ✚ ® remote controls and one Security ✚ ® Keyless Entry System. If you pu ...

  • Chamberlain WD822KS 1/2 HP - page 31

    31 T o Open the Door Manually DISCONNECT THE TROLLEY : The door should be fully closed if possible. Pull down on the emergency release handle (so that the trolley release arm snaps into a vertical position) and lift the door manually . The lockout feature prevents the trolley from reconnecting automatically , and the door can be raised and lowered ...

  • Chamberlain WD822KS 1/2 HP - page 32

    32 CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door operation requiring some re-adjustments, particularly during the first year of operation. Pages 27 and 28 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully . Repeat the safety reverse ...

  • Chamberlain WD822KS 1/2 HP - page 33

    33 HA VING A PROBLEM? 1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • V erify the safety sensors are properly installed, aligned and free of any obstructions. Refer to Installation Step 10: Ins ...

  • Chamberlain WD822KS 1/2 HP - page 34

    34 Installed Safety Sensor Safety Sensor Bell Wire LED or Diagnostic LED "Learn" Button KG 1 3 9 7 5 KG 1 3 9 7 5 Diagnostics Located On Motor Unit Y our garage door opener is programmed with self-diagnostic capabilities. The “Learn” button/diagnostic LED will flash a number of times then pause signifying it has found a potential issu ...

  • Chamberlain WD822KS 1/2 HP - page 35

    *3-Button Remotes If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or compact remote can be programmed to operate other Security ✚ ® garage door openers. T o Erase All Codes From Motor Unit Memory T o deactivate any unwanted remote, first er ...

  • Chamberlain WD822KS 1/2 HP - page 36

    1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Multi-Function Door Control. 3. Continue holding the ENTER and LIGHT buttons while you press the push bar on the Multi-Function Door Control (all three buttons ...

  • Chamberlain WD822KS 1/2 HP - page 37

    7 10 12 5 N O TIC E 6 4 3 2 9 13 8 1 L O C K L IG H T 11 1 2 3 5 4 6 7 Installation Parts 37 REP AIR P ARTS Rail Assembly Parts KEY P ART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41C5141-1 Complete trolley assembly 3 41A5665 Complete rail 4 41B4103 Spring trolley nut 5 144C54 Idler pulley 6 41A5250 Full belt assembly 7 12D598 “U” bracket ...

  • Chamberlain WD822KS 1/2 HP - page 38

    Motor Unit Assembly Parts 38 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSEMBLY Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 2 4 3 7 1 12 15 7 5 8 9 17 19 18 6 10 11 16 13 14 KEY P ART NO. NO. DESCRIPTION 1 41A4371 Belt cap retainer 2 41A4885-5 Gear and sprocket assembly . Complete with: Spring washer; thrust washer; retain ...

  • Chamberlain WD822KS 1/2 HP - page 39

    39 ACCESSORIES LOCK LIGHT C L O S E D O P E N L O C K L IG H T 3-Button SECURITY ✚ ® Remote Control: Includes visor clip. SECURITY ✚ ® Keyless Entry: Enables homeowner to operate garage door opener from outside by entering a password on a specially designed keyboard. Also can add a temporary password for visitors or service persons. This temp ...

  • Chamberlain WD822KS 1/2 HP - page 40

    © 2004, The Chamberlain Group, Inc. 1 14A2784C All Rights Reserved Printed in Mexico CHAMBERLAIN SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SER VICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE SEVEN DA YS A WEEK. SIMPL Y DIAL OUR T OLL FREE NUMBER: 1-800-528-9131 HOURS: (Central Std. Time) 5:00 A.M. TO 7:00 ...

Manufacturer Chamberlain Category Garage Door Opener

Documents that we receive from a manufacturer of a Chamberlain WD822KS 1/2 HP can be divided into several groups. They are, among others:
- Chamberlain technical drawings
- WD822KS 1/2 HP manuals
- Chamberlain product data sheets
- information booklets
- or energy labels Chamberlain WD822KS 1/2 HP
All of them are important, but the most important information from the point of view of use of the device are in the user manual Chamberlain WD822KS 1/2 HP.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Chamberlain WD822KS 1/2 HP, service manual, brief instructions and user manuals Chamberlain WD822KS 1/2 HP. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Chamberlain WD822KS 1/2 HP.

A complete manual for the device Chamberlain WD822KS 1/2 HP, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Chamberlain WD822KS 1/2 HP by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Chamberlain WD822KS 1/2 HP.

A complete Chamberlain manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Chamberlain WD822KS 1/2 HP - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Chamberlain WD822KS 1/2 HP, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Chamberlain WD822KS 1/2 HP, that we can find in the current document
3. Tips how to use the basic functions of the device Chamberlain WD822KS 1/2 HP - which should help us in our first steps of using Chamberlain WD822KS 1/2 HP
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Chamberlain WD822KS 1/2 HP
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Chamberlain WD822KS 1/2 HP in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Chamberlain WD822KS 1/2 HP?

Use the form below

If you did not solve your problem by using a manual Chamberlain WD822KS 1/2 HP, ask a question using the form below. If a user had a similar problem with Chamberlain WD822KS 1/2 HP it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)