Manual John Deere OMM141979 J9

36 pages 6.59 mb
Download

Go to site of 36

Summary
  • John Deere OMM141979 J9 - page 1

    OMM141979 J9 J9 Mechanical Tiller 30-Inch OPERA T OR’S MANU AL North Am erican V ersion Litho in U.S.A. ...

  • John Deere OMM141979 J9 - page 2

    Introduction INTR ODUCTION Introducti on Thank Y ou for Purc hasing This Product W e appreciate y our b usiness and wish y ou many y ears of saf e and satisfied use of y our machin e. Using Y our Operator ’ s Manual This manual is an im por tant par t of your machine and should remain with the machine when you sell it. Reading y our operator’ s ...

  • John Deere OMM141979 J9 - page 3

    Product Identifica tion PR ODUCT IDENTIFICATION Product I dentificat ion Recor d Identification Numbers Mechan ical Tiller 30-Inch Ser ial No . (010001 - ) If you need to contact an Authorized Ser vice Cen ter for inf orm ation on servicing, alwa ys provide the product model and ser ial number . Y ou will need to locate the identification n umber f ...

  • John Deere OMM141979 J9 - page 4

    T able o f Contents TA B L E O F C O N T E N T S All information, illustrations and specifications in this manual are based on the latest information at the time of publication. The right is reser ved to make changes at an y time without notice. COPYRIGHT© 1999 Deere & Co . John Deere Worldwide Commercial and Consumer Equipment Division Horico ...

  • John Deere OMM141979 J9 - page 5

    Saf ety - 1 SAFETY Safety Understanding The Machine Saf ety Labels The machine saf ety labels shown in this section ar e placed in impor tant areas on y our machine to dr aw atten tion to potential saf ety hazards. On y our machine saf ety labels , the words D ANGER, W ARNING, and CA UTION are used with this safety-aler t symbol, ( c ). D ANGER ide ...

  • John Deere OMM141979 J9 - page 6

    Saf ety - 2 SAFETY BEFORE DISMOUNTING OR SER VICING • Shut off engine and remov e key . • Lock br ake f or par k. • L o w e ro rb l o c ku pm a c h i n e . Operate Safel y • Chec k v ehicle brak e action bef ore you oper ate. Adjust or ser vice brakes as necessar y . • Inspect machine bef ore you o perate . Be sure hardw are is tight. Rep ...

  • John Deere OMM141979 J9 - page 7

    Saf ety - 3 SAFETY Practice Safe Maintenance • Underst and ser vic e procedure b ef ore do ing work . K eep area clean an d dr y . • Ne ver lubricate, service, or adjust machine while it is moving. K eep saf ety de vices in place and in working condition. Keep hardware tight. • K eep hands , f eet, clothing, je welry , and long hair a wa y fr ...

  • John Deere OMM141979 J9 - page 8

    Prepare V ehicle - 4 PREPARE V EHICLE Prepare V ehicle Remove Mo wer Deck T ractor mower dec k must be remov ed from bef ore installing tiller . See your tractor oper ator ’ s manual or mo wer deck manual f or remov al instr uctions. Ballasting Requirements All tractor s require front wheel weig hts to be installed when using this tiller . F ollo ...

  • John Deere OMM141979 J9 - page 9

    Installing - 5 INSTALLING Installi ng P ark V ehic le Safel y • Stop v ehicle on a le v el surf ace, not on a slope . • Disengag e PT O . • Engage the park brak e. • ST OP the engin e. • Remo ve th e ke y . • Bef ore you lea v e the operator ’ s seat, wait for engine and all moving par ts to STOP . Setting Depth Contr ol Knob T urn de ...

  • John Deere OMM141979 J9 - page 10

    Installing - 6 INSTALLING handle (B) to rotate tiller housing while pulling left frame rail upward s to gain clearance to l ower fr ame wheels (C). 2. Unlock loc king pin (D) and rotate frame wheel do wn into engaged position and make sure loc king pin locks into loc king hole. Loc k r ight frame wheel d own into eng aged position in similar fashio ...

  • John Deere OMM141979 J9 - page 11

    Installing - 7 INSTALLING Disengage Frame Suppor t Rod 1. Mov e to left side, under tr actor f ootrest — hold lift handle (B) down. 2. Piv ot suppor t rod (C) down in to storage position. 3. Slowly release do wnw ard pressure on lift handle (B) until cups of tiller frame latches (A) are seated up against mounting pins (D). F asten Frame Clip Latc ...

  • John Deere OMM141979 J9 - page 12

    Installing - 8 INSTALLING tiller lift rod (B) upright, align tractor lift link (A) so pin (C) fits into hole (D) of lift link (A). 2. Install M13 x 24 x 2.5 mm w asher (E), from bag of parts, on lift rod pin (C). 3. F asten lift rod to lift link with spring locking ring (F), from bag of par ts. Adjust Tiller Lift Height 1. Push implement lift le ve ...

  • John Deere OMM141979 J9 - page 13

    Removing - 9 REMO VING Removing P ark V ehic le Safel y • Stop v ehicle on a le v el surf ace, not on a slope . • Disengag e PT O . • Engage the park brak e. • ST OP the engin e. • Remo ve th e ke y . • Bef ore you lea v e the operator ’ s seat, wait for engine and all moving par ts to STOP . Mo ve Implement Lift Lever 1. Pull impleme ...

  • John Deere OMM141979 J9 - page 14

    Removing - 10 REMO VING Disengage Belt And Unhook Left Clip Latch 1. Mov e to r ight side , under tractor f ootrest — mov e belt tensioning idler lev er (A) out of “ ENGAGED ” position into “ DISENGA GED ” position (point ing toward front of tractor). 2. Pull and hold tensioning idler (B) towards right frame while you remo ve belt from PT ...

  • John Deere OMM141979 J9 - page 15

    Removing - 11 REMO VING Lock Frame Wheels Into Engage P osition 1. Mov e to left rear , behind tractor dr ive wheels — pull and hold out wheel locking p in (A). 2. Swing left wheel assembly ( B) down into “ ENGA GE ” position. Mak e sure loc king pin engages hole in loc king brac ket. Repeat f or r ight frame wheel. Disengage Frame Suppor t R ...

  • John Deere OMM141979 J9 - page 16

    Operating - 12 OPERATING Operating Tilling Tips Install correct front and rear tractor w eights. See Install W eights and Chains in Installing the Tiller section. Till with engine at F AST thrott le, control g round speed with appropriate transmission spe ed range. Check tines bef ore you till. Replace missing, bent, or brok en tines . When y ou ti ...

  • John Deere OMM141979 J9 - page 17

    Operating - 13 OPERATING Move Implement to “ RAISE ” P osition 1. First push implement lift le v er (A) f orward slightly , then depress and hold do wn button (B) to unlo ck lift le ver loc king mechanism. 2. Pull lift lev er reward out of “ LOWER ” po sition, release button (B) and continue to pull lev er all-the-way re ward until a loud m ...

  • John Deere OMM141979 J9 - page 18

    Operating - 14 OPERATING 3. Mov e to r ight side, below tractor f ootrest — rem ov e spring locking ring (A) and flat washer (B) f or m lift rod pin (C). 4. Remov e lift rod (D) f or m tractor lift link (E). NO TE: Maximum tilling depth is 150 mm (6-in.) — bottom of shaft to bottom edge of lo west tine. Picture Note: Tiller frame removed from t ...

  • John Deere OMM141979 J9 - page 19

    Operating - 15 OPERATING 2. Mov e to left side of tiller housing — grasp han dle (C) to raise tiller housing to remov e pressure on transpor t locking pin (D) and continue to hold tiller housing stationary while yo u pull transport locking pin (D) out and r otate it f orward into “ LOCK-OUT ” p o s i t i o n ,r o l l e dp i n( E )l o c k e di ...

  • John Deere OMM141979 J9 - page 20

    Operating - 16 OPERATING mechanism. 2. Pull lift le v er (A) rew ard out of “ LO WER ” position ( s h o w n ) ,r e l e a s eb u t t o n( B )a n dc o n t i n u et op u l ll e v e ra l l - the-wa y rew ard until a loud metalli c-clic k is heard, signalling lev er is in “ LOCK-OUT ” position, then release lift le ver — it is no w lock ed int ...

  • John Deere OMM141979 J9 - page 21

    Ser vice - 17 SERVIC E Service Service Intervals Checking Belt T ension Picture Note: Tiller removed for c larity purposes only . 1. Chec k position of belt ten sion rod (A): • If rod end is in po sition (B), against the v er tical frame rail (C), the belt i s too tight and m ust be loosened. • If rod end is in position (D ), e xtend s bey ond ...

  • John Deere OMM141979 J9 - page 22

    Ser vice - 18 SERVIC E Cleaning Under Belt Shield Picture Note: Tiller removed for c larity purposes only . 1. Mov e to left side of tiller housing — remove two self- tapping cap screws (A) and belt shield (B). 2. Clean dir t from sheave and surrounding area . 3. Install shield ( B) and self-tapp ing cap screws (A) until snug — DO NO T ov er-ti ...

  • John Deere OMM141979 J9 - page 23

    Ser vice - 19 SERVIC E 2. Loosen flang e lock n ut (A) on tensioning idler . Move be lt guide (B) awa y from belt. 3. Loosen top jam nuts (C), o ne on each side, to tilt guide bolts (D) aw ay from drive shea ve. 4. Remove belt. Install Primary Drive Belt 1. Install belt on d rive shea ve with wide- edge of belt f acing guide bolts (D). 2. Tighten t ...

  • John Deere OMM141979 J9 - page 24

    Ser vice - 20 SERVIC E 7. Remov e secondary b elt (K) from tiller drive shea ve . Install Secondary Drive Belt 1. Install ne w secondar y dr iv e belt with one twist (A), as shown, to seat “ V ” of belt in secondary drive shea v e (B). DO NO T cross-ov er belt (f or ming an “ X ” patter n) when installing or tiller drive rotation will be re ...

  • John Deere OMM141979 J9 - page 25

    Ser vice - 21 SERVIC E 2. Raise tiller as high as it will go if still on tractor . NO TE: For ease in replacing tines, yo u can remove tiller fr om the tractor an d turn it completel y upside down. Put do wn prote ctive tarp or carpet to pr otect paint finish. 3. Put tiller in TRANSPOR T position. (See T ranspor ting Tiller in OPERA TING section.) ...

  • John Deere OMM141979 J9 - page 26

    Ser vice - 22 SERVIC E • MiddleTine Sets : Remo v e lock nut s (A), bolts (B), spacers (C), t wo left tines (D), and two right t ines (E). Remember to inst all ne w bolts so heads a re to left side and ne w lock n uts are to right side . A total of eight spacers are used in these middle tine sets — fo u r i n e a c h set. • Right Tine Set : R ...

  • John Deere OMM141979 J9 - page 27

    T roubl eshooting - 23 T R OUBLESHOOTING Troubleshooting Using T roub leshooting Char t If yo u are ex periencing a problem that is n ot listed in this char t , see your authorized dealer for ser vice. W h e ny o uh a v ec h e c k e da l l t h ep o s s i b l ec a u s e sl i s t e da n d yo u are still e xperiencing the prob lem, see you r authorize ...

  • John Deere OMM141979 J9 - page 28

    Stor age - 24 STORAGE Storage Storing Tiller 1. Remo v e tiller from tr actor . (See the REMO V ING section.) 2. Clean tiller with water pressure. 3. Chec k belts. If necessary , get ne w belts from your A uthorized Service Center . DO NOT in stall the ne w belts until you tak e tiller out of storage . 4. Replac e or repair badly wor n or da maged ...

  • John Deere OMM141979 J9 - page 29

    Assembly - 25 ASSEMBL Y Assembly Identify Parts – 30 Inch Mechanical Tiller Bag of P arts M96256 B C D E F G H L I O K J A M96254 M N P Q Qty . Us ed P ar t Description Size 1 Handle, L ift (A) 2 Pin, Mounting (B) 1 Sheav e, Idler (C) 1 Guide, Belt (D) 2 Bolt, Flange (E) M12 x 1.75 x 50 mm 2 Bolt, Flange ( F) M6 x 1.00 x 30 mm 4 Bolt, He x (G) M8 ...

  • John Deere OMM141979 J9 - page 30

    Assembly - 26 ASSEMBL Y Install T ractor Rear -Frame Hard ware 1. F rom bag of part s, in stall one spacer (A ) on each M12 x 1.75 x 50 mm flange bolt (B). 2. Install spa cers and bolts in BO TT OM holes at rear of tractor fr ame and secure with M12 x 1.7 5 lockn uts (C) on inside of tractor frame. Tighten locknuts to 105 N • m (78 ft- lb). Insta ...

  • John Deere OMM141979 J9 - page 31

    Assembly - 27 ASSEMBL Y Put Tiller Frame Rails In T ransport Position 1. Pull left frame rail up until locking pin (A) can be loc ked into locking br ack et hole. Push do wn on tiller handle (B) to rotate tiller housing while pulling left frame rail up to gain clearance to lo wer left frame wheel. 2. Unlock loc king pin (C) and rotate wheel down in ...

  • John Deere OMM141979 J9 - page 32

    Assembly - 28 ASSEMBL Y NO TE: Make sure belt guide does not mo ve out of position when tighte ning lock nut. 6 . T i g h t e nM 8x1 . 2 5l o c k n u tt o4 0N • m (354 lb-in.). 7. After tightening, mak e sure the idler shea v e rotates freely on the tens ioning ar m. 8. Pull the belt tight and mak e sure belt guide doe s not contact idler shea ve ...

  • John Deere OMM141979 J9 - page 33

    Specifications - 29 SPECIFICATIONS Specific ations Tiller Speci fications Tiller Specifications Dimensions: C u t t i n gW i d t h ................ ................ ............. ................ .......... 7 6 2m m ( 3 0 - i n . ) M a x i m u mC u t t i n gD e p t h ............... ............. ................ ................ ... 1 5 0m m ( 6 - ...

  • John Deere OMM141979 J9 - page 34

    Inde x - 30 INDE X Index B Ballasting Requirements .........................................4 Before Tilling ........................................................12 Belt Shield, Cleaning Under .................................18 Belt Tension, Checking .........................................17 Belt, Disengage ................................... ...

  • John Deere OMM141979 J9 - page 35

    Notes - 31 NOTES Notes ...

  • John Deere OMM141979 J9 - page 36

    Quality Sta tement - 32 QUALITY STATEMENT Quality Stateme nt Y our product , designed and built b y John Deere, is more than just a purchase , it ’ s an inv estment in quality . That quality goes be y ond our equipment to y our dealer ’ sp a r t s and service suppor t. That ’ s wh y John Deere has initiated a process to ha ndle yo ur question ...

Manufacturer John Deere Category Tiller

Documents that we receive from a manufacturer of a John Deere OMM141979 J9 can be divided into several groups. They are, among others:
- John Deere technical drawings
- OMM141979 J9 manuals
- John Deere product data sheets
- information booklets
- or energy labels John Deere OMM141979 J9
All of them are important, but the most important information from the point of view of use of the device are in the user manual John Deere OMM141979 J9.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals John Deere OMM141979 J9, service manual, brief instructions and user manuals John Deere OMM141979 J9. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product John Deere OMM141979 J9.

A complete manual for the device John Deere OMM141979 J9, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use John Deere OMM141979 J9 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of John Deere OMM141979 J9.

A complete John Deere manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual John Deere OMM141979 J9 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the John Deere OMM141979 J9, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the John Deere OMM141979 J9, that we can find in the current document
3. Tips how to use the basic functions of the device John Deere OMM141979 J9 - which should help us in our first steps of using John Deere OMM141979 J9
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with John Deere OMM141979 J9
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of John Deere OMM141979 J9 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning John Deere OMM141979 J9?

Use the form below

If you did not solve your problem by using a manual John Deere OMM141979 J9, ask a question using the form below. If a user had a similar problem with John Deere OMM141979 J9 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)