Manual RedMax G3200EZ

40 pages 1.47 mb
Download

Go to site of 40

Summary
  • RedMax G3200EZ - page 1

    OWNER / OPERA T OR MANUAL CHAINSA WS 848-C3A-93A0 (410) The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our products, please read this manual carefully to understand the proper use of your unit. W ARNING APPLICABLE SERIAL NUMBER ...

  • RedMax G3200EZ - page 2

    ...

  • RedMax G3200EZ - page 3

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL This mark indicates i ...

  • RedMax G3200EZ - page 4

    2. Specifications ■ G3200 / G3200EZ Power unit : Displacement ···················································································· 2.00(31.8) cu-in(cm 3 ) Fuel ············································ ...

  • RedMax G3200EZ - page 5

    3. Symbols on the machine  5  Made in Japan RedMax IMPORT ANT ENGINE INFORMA TION THIS ENGINE CONFORMS T O US EP A PH1 FOR SMALL OFF-RO AD ENGINES. ENGINE F AMIL Y : 4KZXS. 0324RS:EM ENGINE DISPLACEMENT : 32cc REFER T O OWNER'S MANUMAL FOR MAINTE- NANCE SPECIFICA TIONS AND ADJUSTMENTS. MANUF ACTURED : INFORMA TION IMPORT ANTE CONCERNANT ...

  • RedMax G3200EZ - page 6

     6  4. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. 2. Use safety footwear, snug fitting clothing and eye, hearing and head protection devices. 3. Select flat and bare ground for fuelin ...

  • RedMax G3200EZ - page 7

     7  4. For safe operation 17. Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dangerous carbon monoxide. 18. Do not operate a chain saw in a tree unless specially trained to do so. 19. Guard against kickback. Kickback is the upward motion of the guide b ...

  • RedMax G3200EZ - page 8

    A standard saw unit package contains the items as illustrated. (1) Power unit (2) Bar protector (3) Guide bar (4) Saw chain (5) Plug wrench Open the box and install the guide bar and the saw chain on the power unit as follows: The saw chain has very sharp edges. Use thick protective gloves for safety. [G3200] 1. Pull the guard towards the front han ...

  • RedMax G3200EZ - page 9

    5. Installing guide bar and saw chain  9  A new chain will expand its length in the beginning of use. Check and readjust the tension frequently as a loose chain can easily derail or cause rapid wear of itseif and the guide bar. [G3200EZ] 1. Pull the guard towards the front handle to check that the chain brake is not engageg. 2. Loosen the nut ...

  • RedMax G3200EZ - page 10

    5. Installing guide bar and saw chain  10  While temporary tightening, you may hear the “click” sound. But do not stop tightening at that time. This sound does not mean that the saw chain and guide bar were assembled. 5. While holding the chain cover, temporary tighten the nut assembly and fix the bar and chain cover. (You can fix them ev ...

  • RedMax G3200EZ - page 11

    6. Fuel and Chain oil  11  ■ RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1 • Exhaust emission are controlled by the fundamental engine parameters and components(eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion. • These engines are certified ...

  • RedMax G3200EZ - page 12

     12  6. Fuel and Chain oil ■ CHAIN OIL Use motor oil SAE 10W-30 all year round, or SAE 30-40 in summer and SAE 20 in winter. Do not use waste or regenerated oil that can cause damage to the oil pump. NOTE again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary f ...

  • RedMax G3200EZ - page 13

    It is very dangerous to run a chainsaw that mounts broken parts or lacks any parts. Before starting engine, make sure that all the parts including bar and chain are installed properly. ■ STARTING THE ENGINE 1. Fill fuel and chain oil tanks respectively, and tighten the caps securely. (1) Fuel (2) Chain oil 2. Set the switch to “I” position. ( ...

  • RedMax G3200EZ - page 14

     14  6. When engine has ignited, pull the throttle slightly to return the choke knob to the original position. If the engine stops, pull the starter again without pulling out the choke knob. 7. Allow the engine to warm up with the throttle lever pulled slightly. Keep clear of the saw chain as it will start rotatIng upon starting of engine. ? ...

  • RedMax G3200EZ - page 15

    1. H and L needles are restricted within the number of turn as shown below. H needle –1/4 L needle –1/4 2. Start engine and allow it to warm up in low speed for a few minutes. 3. Turn idle adjusting screw (T) counter-clockwise so that saw chain does not turn. If idling speed is too slow, turn the screw clockwise. 4. Make a test cut adjust the H ...

  • RedMax G3200EZ - page 16

     16  7. Operation When the brake engages during operation, immediately release the throttle lever to stop the engine. ■ STOPPING THE ENGINE 1. Release the throttle lever to allow the engine to idle for a few minutes. 2. Set the switch to the “O” (STOP) position. (1) Switch ■ CARBURETOR ANTI-FREEZE MECHANISM Operating chain saws in tem ...

  • RedMax G3200EZ - page 17

    • Before proceeding to your job, read "For Safe Operation" section It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. •A lways follow the safety regulations. The chain saw must only be used for cutting wood. It is forbidden to cut other types of material. Vibrations and kickback vary ...

  • RedMax G3200EZ - page 18

     18  ■ FELLING A TREE (F8-2) 1. Decide the felling direction considering the wind, lean of the tree, location of heavy branches, ease of job after felling and other factors. 2. While clearing the area around the tree, arrange a good foothold and retreat path. 3. Make a notch cut one-third of the way into the tree on the felling side. 4. Mak ...

  • RedMax G3200EZ - page 19

    A Log lying on the ground (F8-3) Saw down halfway, then roll the log over and cut from the opposite side. A Log hanging off the ground (F8-4) In area A, saw up from the bottom one-third and finish by sawing down from the top. In area B, saw down from the top one-third and finish by sawing up from the bottom. Cutting Limb of Fallen Tree (F8-5) First ...

  • RedMax G3200EZ - page 20

     20  9. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. Before cleaning, the inspecting or repairing the unit, make sure that engine has stopped and is cool. Disconnect the spark plug to prevent accidental starting. ■ MAINT ...

  • RedMax G3200EZ - page 21

    9. Maintenance 4. Remove the cleaner element by unfastening the hooks. Split the element into halves and wash in neutral detergent and warm water. After cleaning, dry the element completely. Exchange the element with new one in case it has been contaminated. When reinstalling the element to the unit, fit the hook A and the hole, and then inset the ...

  • RedMax G3200EZ - page 22

     22  Be sure to block the air intake hole. 2. Spark arrester The muffler is equipped with a spark arrester to prevent red hot carbon from flying out of the exhaust outlet. Periodically check and clean as necessary with a wire brush after removing two muffler cover nuts and one screw. (1) Spark arrester Never use a muffler if the spark arreste ...

  • RedMax G3200EZ - page 23

    ■ SAW CHAIN I t is very important for smooth and safe operation to keep the cutters always sharp. Your cutters need to be sharpened when: • Sawdust becomes powder-like. • You need extra force to saw in. • The cut way does not go straight. • Vibration increases. • Fuel consumption increases. Cutter setting standards: Be sure to wear safe ...

  • RedMax G3200EZ - page 24

     24  10. Maintenance of Saw Chain and Guide Bar Make sure every cutter has the same length and edge angles as illustrated. (F10-3) (4) Cutter length (5) Filing angle (6) Side plate angle (7) Top plate cutting angle ■ GUIDE BAR • Reverse the bar occasionally to prevent partial wear. • The bar rail should always be a square. Check for wea ...

  • RedMax G3200EZ - page 25

    11 . T roubleshooting Guide Case 1. Starting failure: Make sure the icing prevention system is not working. Case 2. Lack of power/Poor acceleration/Rough idling Case 3. Oil does not come out Check fuel for water or substandard mixture. Check for engine flooding. Check the spark. Check fuel for water or substandard mixture. Check air filter and fuel ...

  • RedMax G3200EZ - page 26

     26  1. Empty the fuel tank and run the engine out of fuel. 2. Empty the oil tank. 3. Clean the entire unit. 4. Store the unit in a dry place out of the reach of children. 12. Storage ...

  • RedMax G3200EZ - page 27

     27  13. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model ...

  • RedMax G3200EZ - page 28

     28  G3200 13. Parts list Fig.1 POWER UNIT (S/N 404766 and up) ...

  • RedMax G3200EZ - page 29

     29  G3200 Fig.1 POWER UNIT (S/N 404766 and up) Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE 1 848-C30-12A1 CYLINDER 1 2 T2200-14210 GASKET, cyl 1 3 848-C30-2101 CASE ASSY 1 4 2629-21130 • PIN 3 5 06030-06201 • BEARING 2 6 04065-03212 • SNAPRING ø32 1 7 2169-21210 • SEAL 1 8 848-8AC-3210 • SEAL 1 9 2616-21230 • STUD 1 10 848 ...

  • RedMax G3200EZ - page 30

    G3200 13. Parts list Fig.2 POWER UNIT (S/N 404766 and up)  30  ...

  • RedMax G3200EZ - page 31

    G3200 Fig.2 POWER UNIT (S/N 404766 and up)  31  Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE 1 848-C30-82H3 ROD 1 2 848-C30-82G2 GROMMET 1 3 848-C30-25A2 CASE 1 4 848-815-1400 SCREW M5xL14 T27 4 5 848-825-1911 SCREW TP5(P-tight)xL19 T27 1 6 848-C30-25C2 KNOB 1 7 848-C30-25D0 CLIP 1 8 T2200-21230 BOLT 1 9 848-C30-6612 PLATE 1 10 848-C30-6 ...

  • RedMax G3200EZ - page 32

     32  G3200EZ 13. Parts list Fig.3 POWER UNIT (S/N 400001 and up) ...

  • RedMax G3200EZ - page 33

     33  G3200EZ Fig.3 POWER UNIT (S/N 400001 and up) Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE 1 848-C30-12A1 CYLINDER 1 2 T2200-14210 GASKET, cyl 1 3 848-C30-2101 CASE ASSY 1 4 2629-21130 • PIN 3 5 06030-06201 • BEARING 2 6 04065-03212 • SNAPRING ø32 1 7 2169-21210 • SEAL 1 8 848-8AC-3210 • SEAL 1 9 2616-21230 • STUD 1 10 8 ...

  • RedMax G3200EZ - page 34

     34  G3200EZ 13. Parts list Fig.4 POWER UNIT (S/N 400001 and up) ...

  • RedMax G3200EZ - page 35

     35  G3200EZ Fig.4 POWER UNIT (S/N 400001 and up) Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE 1 848-C30-82H3 ROD 1 2 848-C30-82G2 GROMMET 1 3 848-C30-25A2 CASE 1 4 848-815-1400 SCREW M5xL14 T27 4 5 848-825-1911 SCREW TP5(P-tight)xL19 T27 1 6 848-C30-25C2 KNOB 1 7 848-C30-25D0 CLIP 1 8 T2200-21230 BOLT 1 9 848-C30-6612 PLATE 1 10 848-C30 ...

  • RedMax G3200EZ - page 36

    Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE 19 3310-81341 • VALVE 1 20 2880-81470 • SCREW 3 21 2670-81410 • SPRING 1 22 848-C3A-81T0 • SHAFT 1 23 2630-81330 • SCREW 1 24 3350-81380 • SPRING 1 25 2670-81440 • LEVER 1 26 2850-81190 • SCREW 1 27 2841-81450 • VALVE 1 28 T2002-81350 • SPRING 1 29 848-C30-81E0 • SHAFT 1 30 285 ...

  • RedMax G3200EZ - page 37

     37  G3200/G3200EZ Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE 1 848-CB1-2020 BAR CV30 1/4 1 2 3310-52210-50 CHAIN OREGON 25AP-J68E 1 3 3617-97110 PROTECTOR 300~350mm 1 (OP) 4 3320-91140 WRENCH 1 5 848-C3A-93A0 OWNER'S MANUAL 1 6 848-C30-0610 GASKET KIT 1 (OP) 7 T3195-91110 BAG 1 8 2670-91150 DRIVER 1 9 2670-96220 STOPPER (for pist ...

  • RedMax G3200EZ - page 38

    EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. EMISSION-RELATED PARTS ARE: THE CARBURETOR ...

  • RedMax G3200EZ - page 39

    Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage défectueux ...

  • RedMax G3200EZ - page 40

    KOMA TSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093 ...

Manufacturer RedMax Category Chainsaw

Documents that we receive from a manufacturer of a RedMax G3200EZ can be divided into several groups. They are, among others:
- RedMax technical drawings
- G3200EZ manuals
- RedMax product data sheets
- information booklets
- or energy labels RedMax G3200EZ
All of them are important, but the most important information from the point of view of use of the device are in the user manual RedMax G3200EZ.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals RedMax G3200EZ, service manual, brief instructions and user manuals RedMax G3200EZ. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product RedMax G3200EZ.

Similar manuals

A complete manual for the device RedMax G3200EZ, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use RedMax G3200EZ by users. Manuals are usually written by a technical writer, but in a language understandable to all users of RedMax G3200EZ.

A complete RedMax manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual RedMax G3200EZ - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the RedMax G3200EZ, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the RedMax G3200EZ, that we can find in the current document
3. Tips how to use the basic functions of the device RedMax G3200EZ - which should help us in our first steps of using RedMax G3200EZ
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with RedMax G3200EZ
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of RedMax G3200EZ in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning RedMax G3200EZ?

Use the form below

If you did not solve your problem by using a manual RedMax G3200EZ, ask a question using the form below. If a user had a similar problem with RedMax G3200EZ it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)