English dropdown-ico

Manual Chamberlain WD822KD

40 pages 2.69 mb
Download

Go to site of 40

Summary
  • Chamberlain WD822KD - page 1

    The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 www.chamberlain.com GARAGE DOOR OPENER Model WD822KD 1/2 HP For Residential Use Only Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless Th ...

  • Chamberlain WD822KD - page 2

    2 TABLE OF CONTENTS Introduction 2-7 Safety symbol and signal word review . . . . . . . . . . . . . . . 2 Preparing your garage door . . . . . . . . . . . . . . . . . . . . . . . 3 Tools needed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 ...

  • Chamberlain WD822KD - page 3

    3 Stepladder Carpenter’s Level (optional) Tape Measure Drill Sockets and Wrench 1/2", 5/8", 7/16", 9/16" and 1/4" Pencil Wire Cutters Pliers Adjustable End Wrench Claw Hammer Screwdriver Hack Saw Drill Bits 3/16", 5/16" and 5/32" Preparing your garage door Before you begin: • Disable locks. • Remove any ...

  • Chamberlain WD822KD - page 4

    4 Planning Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may fi nd it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener. Depending on your re ...

  • Chamberlain WD822KD - page 5

    5 Planning (Continued) ONE-PIECE DOOR INSTALLATIONS • Generally, a one-piece door does not require reinforcement. If your door is lightweight, refer to the information relating to sectional doors in Installation Step 11. • Depending on your door’s construction, you may need additional mounting hardware for the door bracket (Step 11). Without ...

  • Chamberlain WD822KD - page 6

    6 Your garage door opener is packaged in one carton which contains the motor unit and all parts illustrated below. Accessories will depend on the model purchased. If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for assembly and installation is shown on the next page. Save the carton and packing ...

  • Chamberlain WD822KD - page 7

    7 Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. ASSEMBLY HARDWARE Bolt 1/4"-20x1-3/4" (2) Lock Washer 3/8" (1) Spring/Trolley Nut (1) Nut 3/8" (1) Lock Nut 1/4"-20 (2) Master Link (2) INSTALLATION HARDWARE Carriage Bolt 1/4"-20x1/2" (2) Wing Nut 1/4 ...

  • Chamberlain WD822KD - page 8

    8 ASSEMBLY STEP 1 Assemble the Rail & Install the Trolley To avoid installation diffi culties, do not run the garage door opener until instructed to do so. The front rail has a cut out “window” at the door end (see illustration). The hole above this window is larger on the top of the rail than on the bottom. A smaller hole 3-1/2" (8.9 ...

  • Chamberlain WD822KD - page 9

    9 ASSEMBLY STEP 2 Fasten the Rail to the Motor Unit • Insert a 1/4"-20x1-3/4" bolt into the cover protection bolt hole on the back end of the rail as shown. Tighten securely with a 1/4"-20 lock nut. Do NOT overtighten. • Remove the two bolts from the top of the motor unit. • Place the “U” bracket, fl at side down, on the m ...

  • Chamberlain WD822KD - page 10

    10 ASSEMBLY STEP 4 Install the Belt and Attach the Belt Cap Retainer 1. Pull the belt around the idler pulley and toward the trolley. The ribbed side must contact the pulley. 2. Hook the trolley connector into the retaining slot on the trolley as shown. 3. With the trolley against the screwdriver, dispense the remainder of the belt along the rail l ...

  • Chamberlain WD822KD - page 11

    11 ASSEMBLY STEP 5 Set the Tension • Insert a screwdriver tip into one of the nut ring slots and brace it fi rmly against the trolley. • Place a 7/16" open end wrench on the square end. Rotate the nut about 1/4 turn until the spring releases and snaps the nut ring against the trolley. This sets the spring to optimum belt tension. You have ...

  • Chamberlain WD822KD - page 12

    12 INSTALLATION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door. 1. Close the door and mark the inside vertical centerline of the garage door. 2. Extend the line onto the header wall above the door. You can fasten the header bracket within 4 f ...

  • Chamberlain WD822KD - page 13

    13 INSTALLATION STEP 2 Install the Header Bracket You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided). WALL HEADER B ...

  • Chamberlain WD822KD - page 14

    14 INSTALLATION STEP 4 Position the Opener Follow instructions which apply to your door type as illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid fl at is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder. You will need help at this point if the ladder is not ...

  • Chamberlain WD822KD - page 15

    15 INSTALLATION STEP 5 Hang the Opener Three representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On fi nished ceilings (Figures 2 and 3), attach a sturdy metal bracket to structural supports before installing the opener. This bracket and fastening hardware are not p ...

  • Chamberlain WD822KD - page 16

    16 To prevent possible SERIOUS INJURY or DEATH from electrocution: • Be sure power is NOT connected BEFORE installing door control. • Connect ONLY to 24 VOLT low voltage wires. To prevent possible SERIOUS INJURY or DEATH from a closing garage door: • Install door control within sight of garage door, out of reach of children at a minimum heigh ...

  • Chamberlain WD822KD - page 17

    17 INSTALLATION STEP 7 Install the Lights • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install a 100 watt maximum light bulb in each socket. Light bulb size should be A19, standard neck only. The lights will turn ON and remain l ...

  • Chamberlain WD822KD - page 18

    18 To prevent possible SERIOUS INJURY or DEATH from electrocution or fi re: • Be sure power is NOT connected to the opener, and disconnect power to circuit BEFORE removing cover to establish permanent wiring connection. • Garage door installation and wiring MUST be in compliance with ALL local electrical and building codes. • NEVER use an ex ...

  • Chamberlain WD822KD - page 19

    19 INSTALLATION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR When properly connected and aligned, the sensor will detect an obstacle in the path of its electronic beam. ...

  • Chamberlain WD822KD - page 20

    20 INSTALLING THE BRACKETS Be sure power to the opener is disconnected. Install and align the brackets so the sensors will face each other across the garage door, with the beam no higher than 6" (15 cm) above the fl oor. They may be installed in one of three ways, as follows. Garage door track installation (preferred): • Slip the curved arm ...

  • Chamberlain WD822KD - page 21

    21 MOUNTING AND WIRING THE SAFETY REVERSING SENSORS Mounting: • Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension (Figure 5). • Finger tighten the wing nuts. ...

  • Chamberlain WD822KD - page 22

    22 ALIGNING THE SAFETY REVERSING SENSORS • Plug in the opener. The indicator lights in both the sending and receiving eyes will glow steadily if wiring connections and alignment are correct. The sending eye amber indicator light will glow regardless of alignment or obstruction. If the green indicator light in the receiving eye is off, dim, or fl ...

  • Chamberlain WD822KD - page 23

    23 INSTALLATION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel. Figure 1 shows one piece of ...

  • Chamberlain WD822KD - page 24

    24 ONE-PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also. • Center the door bracket on the top of the door, in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes. • Metal Doors: Drill 3/16" pilot holes ...

  • Chamberlain WD822KD - page 25

    25 INSTALLATION STEP 12 Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONLY • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the pu ...

  • Chamberlain WD822KD - page 26

    26 Figure 5 Figure 6 Straight Door Arm Curved Door Arm (Groove facing out) Straight Door Arm Curved Door Arm CORRECT INCORRECT ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 5: IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm. • Fasten the straight and curved door arm sections together to the longest po ...

  • Chamberlain WD822KD - page 27

    27 Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. • If one control (force or travel limits) is adjusted, the other control ...

  • Chamberlain WD822KD - page 28

    28 Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Too much force on garage door will interfere with proper operation of safety reversal system. • NEVER increase force beyond minimum amount required to close garage door. • NEVER use for ...

  • Chamberlain WD822KD - page 29

    29 Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • Safety reversal system MUST be tested every month. • If one control (force or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made, t ...

  • Chamberlain WD822KD - page 30

    30 OPERATION IMPORTANT INSTALLATION INSTRUCTIONS To reduce the risk of SEVERE INJURY or DEATH: WARNING WARNING WARNING WARNING 1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS. 2. ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with garage door control push buttons or remote controls. 3. ONLY activate ...

  • Chamberlain WD822KD - page 31

    31 To Open the Door Manually DISCONNECT THE TROLLEY: The door should be fully closed if possible. Pull down on the emergency release handle (so that the trolley release arm snaps into a vertical position) and lift the door manually. The lockout feature prevents the trolley from reconnecting automatically, and the door can be raised and lowered manu ...

  • Chamberlain WD822KD - page 32

    32 The lithium battery should produce power for up to 5 years. To replace battery, use the visor clip or screwdriver blade to pry open the case as shown. Insert battery positive side up (+). Dispose of old battery properly. Replace the battery with only 3V2032 coin cell batteries. To prevent possible SERIOUS INJURY or DEATH: • NEVER allow small c ...

  • Chamberlain WD822KD - page 33

    33 6. My motor unit hums briefl y: • First verify that the trolley is against the stop bolt. • Release the door from the opener by pulling the Emergency Release Rope. • Manually bring the door to a closed position. • Loosen the belt by adjusting the outer nut 4 to 5 turns. This relieves the tension. • Run the motor unit from the remote c ...

  • Chamberlain WD822KD - page 34

    34 Diagnostic Chart Safety reversing sensors slightly misaligned (dim or fl ashing LED). Door control or wire shorted. Safety reversing sensors wire shorted or black/white wire reversed. Safety reversing sensors wire open (broken or disconnected). OR Symptom: One or both of the Indicator lights on the safety sensors do not glow steady. • Inspect ...

  • Chamberlain WD822KD - page 35

    35 To Erase All Codes From Motor Unit Memory To deactivate any unwanted remote, fi rst erase all codes: Press and hold the “learn” button on motor unit until the learn indicator light goes out (approximately 6 seconds). All previous codes are now erased. Reprogram each remote or keyless entry you wish to use. PROGRAMMING NOTICE: If this Securi ...

  • Chamberlain WD822KD - page 36

    36 To Add, Reprogram or Change a Keyless Entry PIN NOTE: Your new Keyless Entry must be programmed to operate your garage door opener. USING THE “LEARN” BUTTON USING THE MULTI-FUNCTION DOOR CONTROL 1. Enter a four digit personal identifi cation number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER but ...

  • Chamberlain WD822KD - page 37

    37 REPAIR PARTS Rail Assembly Parts KEY PART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41C5141-2 Complete trolley assembly 3 41A5665-2 Complete rail 4 41B4103 Spring trolley nut 5 144C54 Idler pulley 6 41A5250 Full belt assembly 7 41D598-1 “U” bracket NOT SHOWN 183A163 Wear pads 8808CB 8 Foot (2.4 m) Rail extension kit 8810CB 10 Foot (3 m) ...

  • Chamberlain WD822KD - page 38

    38 KEY PART NO. NO. DESCRIPTION 1 41A4371 Belt cap retainer 2 41A4885-5 Gear and sprocket assembly. Complete with: Spring washer, thrust washer, retaining ring, bearing plate, roll pins (2), drive gear and worm gear, helical gear with retainer and grease 3 41A2817 Drive/worm gear kit with grease, roll pins (2) 4 41B4245 Line cord 5 41A5484-10 End p ...

  • Chamberlain WD822KD - page 39

    39 ACCESSORIES 760CB Outside Quick Release: Required for a garage with NO access door. Outdoor Key Switch: Operates the garage door automatically from outside when remote control is not handy. 7702CB 41A5281 CLLAD Extension Brackets: (Optional) For safety sensor installation onto the wall or fl oor. To order call: 1-800-528-9131 Remote Light Contr ...

  • Chamberlain WD822KD - page 40

    CHAMBERLAIN ® SERVICE IS ON CALL OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE. SIMPLY DIAL OUR TOLL FREE NUMBER: 1-800-528-9131 www.chamberlain-diy.com For professional installation, parts and service , contact your local CHAMBERLAIN ® dealer. Look for him in the Yellow Pages, or c ...

Manufacturer Chamberlain Category Garage Door Opener

Documents that we receive from a manufacturer of a Chamberlain WD822KD can be divided into several groups. They are, among others:
- Chamberlain technical drawings
- WD822KD manuals
- Chamberlain product data sheets
- information booklets
- or energy labels Chamberlain WD822KD
All of them are important, but the most important information from the point of view of use of the device are in the user manual Chamberlain WD822KD.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Chamberlain WD822KD, service manual, brief instructions and user manuals Chamberlain WD822KD. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Chamberlain WD822KD.

Similar manuals

A complete manual for the device Chamberlain WD822KD, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Chamberlain WD822KD by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Chamberlain WD822KD.

A complete Chamberlain manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Chamberlain WD822KD - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Chamberlain WD822KD, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Chamberlain WD822KD, that we can find in the current document
3. Tips how to use the basic functions of the device Chamberlain WD822KD - which should help us in our first steps of using Chamberlain WD822KD
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Chamberlain WD822KD
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Chamberlain WD822KD in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Chamberlain WD822KD?

Use the form below

If you did not solve your problem by using a manual Chamberlain WD822KD, ask a question using the form below. If a user had a similar problem with Chamberlain WD822KD it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)