Manual Craftsman 139.53675SRT

40 pages 4.31 mb
Download

Go to site of 40

Summary
  • Craftsman 139.53675SRT - page 1

    Owner's Manual Model No. 139.53662SRT 139.53675SRT For Residential Use Only Caution: Read and follow all safety rules and operating instructions before first use of this product. Fasten the manual near the garage door after installation. Compffeswith UL325/Ih _ re_lations effective January 1, I9_3 . ii ® GARAGE DOOR OPENER 1/2 HP = Safety Pre ...

  • Craftsman 139.53675SRT - page 2

    Contents Page A review of safety alert syrnboFs........................................ 2 You'll need tools ............................................................................... 3 Safety information regarding garage door locks and ropes ............................................................. 3 Testing your garage door for stick ...

  • Craftsman 139.53675SRT - page 3

    You'll Need Tools During assembly, installation and adjustment of the opener, instructions will call for hand tools shown below S_e_adder Tape Measure Per'<_ Hac_ Saw Claw Hammer A_ustable End Wtenc_ i , i i i i i,i An unbalanced garage door might not reverse when required and someone under the door could be seriously injured or killed ...

  • Craftsman 139.53675SRT - page 4

    .............. . .. ........... :., _. ........ . _ Before you begin, survey your garage area to see whether any of the conditions below apply to your installation. Slack in Chain Tension is No_ When Garage Door is Clo_ed Extension Sp_ing OR Access Door 0 Safety Reversing Sensor Based on your particular requirements, there are several installation ...

  • Craftsman 139.53675SRT - page 5

    Based on your particular requirements, there are several instaJlat_on steps which might call for materiaJs and/or hardware not included in the carton. '. Step 1, page 13 - Look at the wail or ceiling above the garage door. The header bracket mustbe securely fastened to structural supports° • Step 5, page 17 - Do you havea finished ceiling i ...

  • Craftsman 139.53675SRT - page 6

    Carton Inventory Your garage door opener is packaged in two cartons which contain aJl parts illustrated below.. If anything is missing, carefully check the packing matedaJ. Parts may be "stuck = in the foam. Hardware for assembly and installation is shown on page 7o Model 53675 on{y Premium Coetr_ Console SECURITY+ Three-Function Retake Conm:_ ...

  • Craftsman 139.53675SRT - page 7

    Separate all hardware from the packages in the rail carton and the opener carton, as shown below, for the assembly and installation procedures. Assembly Hardware Waslkei'ed Screw Hex Screw Nut 5/16"-18xl/2" (2) 5/16*-18x7fS" (3) 5./16%18 (5} {rilotlnted _i opene[) Trolley Threaded Shall (1) C_-riage Bolts 1t4"-20×1/2" ...

  • Craftsman 139.53675SRT - page 8

    Assembly Section: Pages 8 - 11 To avoid installation difficulties, do not run the garage door opener until instructed to do so. Assembly Step 1 Assemble the T-raft & Attach the Cable Pulley Bracket . Place the 3 T-rail sections on a flat surface for assembly. The end sections are identical. Make sure the "arrow label" on the center se ...

  • Craftsman 139.53675SRT - page 9

    Assembly Step 2 Install the Trolley on the T-rail • Attach the threaded shaft to the trolley with the lock washer and nuts as shown° T_ey Lock Washer 5/16" Inner Nut 5/16" Hardware Shown Actual Size Lo_ W_he r 5/16" © NuI =J16"-18 Trottey Assembly Step 3 ! Fasten the T-rail to the Opener • Place the opener on packing mater ...

  • Craftsman 139.53675SRT - page 10

    Assembly Step 4 Install the Chain/Cable & Attach the Sprocket Cover Dispensing C, arlc, r_ Leave Chain and Cable {nside Dispensing Carton to Prevec_t K3nking, Kee_ Cha;n and Cable Taul When Dispensing • Detach the cable loop from the carton and fasten it to the trolley with a master tink from the hardware bag. See master link procedure, Figur ...

  • Craftsman 139.53675SRT - page 11

    Assembly Step 5 _ghten the Chain & Cable • Spfn the inner nut and lock washer down the threaded shaft, away from the trolley. • To tighten the chain, turn outer nut in the direction shown. As you turn the nut, keep the chain from twisting. When the chain is approximately 1/2" above the base of the T-rail at its midpoint, re-tighten the ...

  • Craftsman 139.53675SRT - page 12

    Installation Section: Pages 12 - 27 • =, L ,,, Installation Step 1 Determine Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door. ,= = ,== ........................... , H, _de_ WaM .J VertJc_ GuideSne __ FinL_hed __ Ceiling if the header bracket is not rigidly faste ...

  • Craftsman 139.53675SRT - page 13

    Pead the Safety instructions on page 12. They also apply to doors withm_t tracks. • Close the door and mark the inside ve_c_t centedine of your garage door. Extend the fine onto the header wall above door. If headroom clearance is minimal, you can install the header bracket on the ceiling° See page 14. • If you need to install the header brack ...

  • Craftsman 139.53675SRT - page 14

    Installation Step 2 Install the Header Bracket I You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the Instructions which will work best for your particular requirements. Fasten the Header Bracket to the Wall • Center the bracket on the vertical guideline with the bottom edge of the bracket on t ...

  • Craftsman 139.53675SRT - page 15

    Installation Step 3 Attach the T-rail to the Header Bracket • Position the opener on the garage floor below the header brackeL Use packing material as a protective base., If the door spring is in the way you'll need help. Have someone hold the opener securely on a temporary support to a!low the T-rail to clear the spring, • Position the ca ...

  • Craftsman 139.53675SRT - page 16

    w ......... Installation Step 4 Position the Opener =ollow Instructions which apply to your door type as illustrated. A 2x4 laid flat Is convenient for setting an ideal door-to-T-rail distance. • Raise the opener onto a stepladder. You will need help at this point ff the/adder is not tall enough. • Open the door aJl the way and place a 2x4 laid ...

  • Craftsman 139.53675SRT - page 17

    installation Step 5 Hang the Opener Two representative installations are shown. Yours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On inished ceilings, F_gure 2, attach a sturdy metal bracket to structural supports before installing the opener. The bracket and fastening hardware are not supplied. See acce ...

  • Craftsman 139.53675SRT - page 18

    • ,ll i installation Step 6 Install the Premium Control Console Locate the door control within sight of the door at a minimum height of 5 feet where small children cannot reach, and away from all moving parts of the door and door hardware. The door control is typically attached directly to the wall If installing into drywall, ddll 5/32" hole ...

  • Craftsman 139.53675SRT - page 19

    6_ Attach the User Safety Instruction label to the wall near the door control, and the Maintenance Instruction label in a prominent tocai_on on the inside of the garage door. Page 32 explains how to use the door control. Do NOT connect the power and operate the openerat this time. The trolley will travel to the full open posltlon but will not retur ...

  • Craftsman 139.53675SRT - page 20

    .... i ,,,,u,uJl Installation Step 9 Electrical Requirements To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin_ This plug will onlyfit into a grounding type cutlet.. If the plug doesn_ fit into the outlet you have, contact a qualified electrician to install the proper outlet, To preve ...

  • Craftsman 139.53675SRT - page 21

    The Safety Reversing System Information you'll need before you begin the installation of the safety reversing sensor. The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction° This is a required safety device and cannot be disabled. Installation procedures are the same f ...

  • Craftsman 139.53675SRT - page 22

    Installation Step 10 " ---] Figures 2 and 3 show assembly of brackets and "C" wrap based on the recommended installation of the sensors as shown on page 21. However, Figures 4 and 5 are variations which may rr_ your installation requirements better° Make sure the wraps and brackets are aligned so the sensors will face each other acr ...

  • Craftsman 139.53675SRT - page 23

    o Center each sensor unit in a "C"wrap with lenses pointing toward each other across the door (see _gure 6). • Secure sensors with the hardware shown° Finger tighten the wing nut on the receiving eye to allow for final adjustment. Securely tighten the sending eye wing nut. • Run the wires from both sensors to the opener. Use insulate ...

  • Craftsman 139.53675SRT - page 24

    i ,,i ,,ll, ii,ll i Installation Step 11 Fasten Door Bracket Follow Instructions which apply to your door type as illustrated below or on page 25. ILl, Ill, A horizontal brace should be long enough to be secured to 2 vertical supports. A vertical brace should cover the height of the top panel. The Illustration shows one piece of angle iron as the h ...

  • Craftsman 139.53675SRT - page 25

    P'.ease read and comply with the warnings and reinforcement instructions on page 24. They apply to one-piece doors also. 1 1 I 2x4 Support Vertical Cente_ne of Ooor • Center the bracket on the top of the door, in line with the header bracket as shown. Mark holes° • Drill 5/16" pilot holes and fasten the door bracket with hardware sup ...

  • Craftsman 139.53675SRT - page 26

    Installation Step 12 Connect Door Arm to Trolley Follow Instructions which apply to your door type as tUustrated below and on page 27. ll,lllllll i Ill Ill :" Make sure garage door is fully closed, Pull the emergency release handle to disconnect the outer trolley from the inner trolley, Slide the outer trolley back (away from the door) about 2 ...

  • Craftsman 139.53675SRT - page 27

    Assemble the Door Arm: • Fasten the straight and curved door arm sections together to the longest possible length, w_ a 2 or 3 hole ovedap. • With the door closed, connect the straight door arm section to the door bracket with the 5-16" × 1-1/4' clevis pin. • Secure with a ring fastener° Ooor Rir_g Brad<or _.j_,-_JO----- Fasten ...

  • Craftsman 139.53675SRT - page 28

    Adjustment Section: Pages 28 -30 Adjustment Step 1 Adjust the UP and DOWN Limits Do not make any limit adjustments until the safety reversing sensors are completely installed_ Limit adjustment settings regulate the points at which the door will stop when moving up or down. The door will stop in the up direction if anything interferes with door trav ...

  • Craftsman 139.53675SRT - page 29

    ill ...... _J,J_ i,,, HH IL_ I Adjustment Step 2 Adjust the Force J,, ii i,i NIl ,,q,,iH ill ii Force adjustment controls are located on the right side panel of the opener. Force adjustment settings regulate the amount of power required to open and close the door. The door will stop in the up direction if anything interferes with its travel. The do ...

  • Craftsman 139.53675SRT - page 30

    Adjustment Step 3 Test The Safety Reversing Sensor , Press the remote control push button to open the door. ° Place the opener carton in the path of the door. • Press the remote control push bt_on to close the door. The door will not move more than an inch, and the opener light(s) wi!l flash. Professional service is required if the opener closes ...

  • Craftsman 139.53675SRT - page 31

    IMPORTANT SAFETY INSTRUCTIONS ii _ L, ....... I ii i........ i_ i _,?. iiiiii To reduce the risk of severe injury or death to persons: 1. READ AND FOLLOW ALL INSTRUCTIONS. 5. If possible, use the emergency release only 2. Do not permit children either to operate or to when the door is in a closed position. Caution play with the opener. Keep remote ...

  • Craftsman 139.53675SRT - page 32

    Operation of Your Opener Activate the opener with any of the following: • The Remote Control: Hold push button down until the door starts to mover - The Door Control: Hold push button down until the door starts to move. • The Outdoor Key Switch or Keyless Entry: (See Accessories) When the opener is activated with the safety reversing sensor ins ...

  • Craftsman 139.53675SRT - page 33

    Receiver and Remote Control Programming Your garage door opener receiver and remote control have been pro-set at the factory. The door will open when you press the LARGE remote control push button,, The code between the remote control and the receiver changes with each use, randomly accessing over 100 bilIion new codes. The 3-function remote contro ...

  • Craftsman 139.53675SRT - page 34

    Having a Problem? Situation Probable Cause and Solution "The opener doesn't operate from either the Door Control or the remote controb ....... J 1. Does the opener have electric power?. Plug a lamp into the oLr_et. If it doesn't light, check the fuse box or the circuit breaker._ (Some outlets are controlled by a door switch.) 2o Have ...

  • Craftsman 139.53675SRT - page 35

    *t i ,_ Having a Problem? (continued) Situation The door opens but won't close: Probable Cause & Solution i i l llll lllll i i ill i i i i Illll I I N,ll 1. If the opener lights blink, check the safety reversing sensor. See page 23, 2. If the opener lights do not blink and it is a new installation, check the down force. See Adjustment Step ...

  • Craftsman 139.53675SRT - page 36

    Rail Assembly Parts Repair Parts 3 Installation Parts NO. NO. t 41A4884 2 41A5032 3 10A19 4 298134 5 31 D431 6 31B430 7 '10A2 8 41 A2828 9 41A4353 10 217A238 11 178B35 t 2 41 A5047 13 41A4373A 4 KEY NO. 1 2 3 4 5 6 7 14 12B483 15 12B484 16 12B485 17 12B350 18 178B34 41 A3475-4 41A41t6 114A2122 4 DESCRIPTION Premium controlconsote 3-function re ...

  • Craftsman 139.53675SRT - page 37

    , )p(:ner Assembly Parts I Repair Parts =nn= 19 18 17 KEY PART NO. NO. DESCRIPTION 1 31 D380 2 41 C4220A 3 41A2817 4 41 B4245 5 41 C4253 6 41 A5021-2 7 4tA4351 8 175B88 15 13 14 Sprocket cover Gear and sprocket assembly Complete with: Spring washer Thrust washer Retaining ring Bearing plate Roll pins (2) Drive gear and worm gear Helical gear w/reta ...

  • Craftsman 139.53675SRT - page 38

    ACCESS,. .............................. ,,,,,,,,, ,,,,, .......................... Sears offers many useful accessories for your garage door opener, They are Illustrated below _ tth Sears model numbers and descriptions. iii iii i ,111 ,,,,, ,,,,,, ,,,,,,,11111111 iu 139.53702 Emergency Key Release: J 139.53703 Required for a garage with NO access d ...

  • Craftsman 139.53675SRT - page 39

    Index Access Door/Outside Key Release Accessory ................................................................................................ 4, 5 Electrical Safety Warnings .................................................................................................................................... 2, 20, 31 Garage Door Testing for balanc ...

  • Craftsman 139.53675SRT - page 40

    For professional installation Cal! 24 hours a day, 7 days a week t -800-865..6500 For the repair or replacement parts you need Call 7 am - 7 pm, 7 days a week t -800-366-PART (1-800-366-7278) For in-home major brand repair service Call 24 hours a day, 7 days a week t -800-4-RIEPAIR (1-800-473-7247) For the location of a Sears Repair Service Center ...

Manufacturer Craftsman Category Garage Door Opener

Documents that we receive from a manufacturer of a Craftsman 139.53675SRT can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 139.53675SRT manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 139.53675SRT
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 139.53675SRT.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 139.53675SRT, service manual, brief instructions and user manuals Craftsman 139.53675SRT. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 139.53675SRT.

A complete manual for the device Craftsman 139.53675SRT, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 139.53675SRT by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 139.53675SRT.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 139.53675SRT - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 139.53675SRT, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 139.53675SRT, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 139.53675SRT - which should help us in our first steps of using Craftsman 139.53675SRT
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 139.53675SRT
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 139.53675SRT in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 139.53675SRT?

Use the form below

If you did not solve your problem by using a manual Craftsman 139.53675SRT, ask a question using the form below. If a user had a similar problem with Craftsman 139.53675SRT it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)