English dropdown-ico

Manual RedMax BC3401DL

38 pages 0.47 mb
Download

Go to site of 38

Summary
  • RedMax BC3401DL - page 1

    The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. WARNING OWNER / OPERA T OR MANUAL BRUSHCUTTERS T1196-93110(112) BC3401DL BC4401DW  Thank you for purchasing a RedMax product. Before using our brushcutters, please read this manual carefully to under ...

  • RedMax BC3401DL - page 2

    Read this manual carefully to understand all safety precautions, controls, proper operation and maintenance of your RedMax brushcutters. Failure to do so could result in serious injury . Instructions labeled as shown at left, concern critical steps or procedures which must be followed in order to prevent accidents which could lead to serious bodily ...

  • RedMax BC3401DL - page 3

    CONTENTS Safety Precautions······················································································· 4 In Order To Ensure Proper And Safe Operation Of Your Brushcutter Work Gear And Clothing Warnings Considering Handling Of Fuel Things To Check Befo ...

  • RedMax BC3401DL - page 4

    ❲ 4 ❳ ■ In order to ensure proper and safe operation of your brushcutter • Read this Owner/Operator Manual carefully. Be sure you understand how to operate this unit properly before you use it. Failure to do so could result in serious injury. • Be sure to keep this manual handy so that you may refer to it later whenever any questions aris ...

  • RedMax BC3401DL - page 5

    Safety Precautions ■ Work gear and clothing • When using your brushcutter, always be sure to wear strong, durable, work clothing; shirts should be long-sleeved shirts and pants should be full-length pants reaching down to the ankles. • Always be sure to wear helmet and face protector when using your brushcutter. • When using your brushcutte ...

  • RedMax BC3401DL - page 6

    ❲ 6 ❳ Safety Precautions ■ Things to check before using your brushcutter • Before beginning work, look around carefully to get a feel for the shape of the land, grass to be trimmed, and whether or not there are any obstacles which might get in the way while working, and remove any obstacles before beginning work. • The area within a perim ...

  • RedMax BC3401DL - page 7

    ■ Things to be careful about when using your brushcutter • When using your brushcutter, grip the handles of the brushcutter firmly with both hands, place your feet slightly apart (slightly further apart than the width of your shoulders) so that your weight is distributed evenly across both legs, and always be sure to maintain a steady, even pos ...

  • RedMax BC3401DL - page 8

    ❲ 8 ❳ Safety Precautions ■ Notes on care and maintenance of your brushcutter • In order to maintain your brushcutter in proper working order, perform the maintenance and checking operations described in this manual at regular intervals. In the event that any parts must be replaced or any maintenance or repair work not described in this manu ...

  • RedMax BC3401DL - page 9

    ■ MOUNTING ENGINE • Put the engine onto the clutch side end of the driveshaft assembly, making the fuel tank and the cutter head come to the same side. Attach the engine firmly with the 4 screw provided. ■ INSTALLING HANDLE • Mount the handle to the shaft tube and clamp it at your best operating position. ■ INSTALLING DEBRIS GUARD • Put ...

  • RedMax BC3401DL - page 10

    ■ PUTTING ON WAIST PAD (BC4401DW only) • Warp the waist pad around the shaft tube and the throttle wire. ■ INSTALLING CUTTING HEAD 1. While locking the gear shaft by inserting the attached bar into the upper holder and the gear box, loosen and remove the hexagon bolt(left-handed) 2. Fit the spacer attached to the head assembly between the upp ...

  • RedMax BC3401DL - page 11

    • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m(10ft) away from the fueling point before starting the engine. • The RedMax engines are lubricated by oil specially formulated ...

  • RedMax BC3401DL - page 12

    4. Shift the ignition switch to the START position. 5. Pull the starter rope. • The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by putting the throttle into the start position. When starting the engine, place the product onto the ground in a flat clear area a ...

  • RedMax BC3401DL - page 13

    • Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures. 6.When the engine has started, move the choke lever gradually downward to open the choke. 7.Allow the engine to warm up for a half minute before starting operation. 1.When restarting the engine immediately after stopping it, leave t ...

  • RedMax BC3401DL - page 14

    ❲ 14 ❳ Operation growth. The rate of cutting motion will depend on the material being cut. Heavy growth will require slower action than will light growth. 5. Never swing the unit so hard as you are in danger of losing your balance or control of the unit. 6. Try to control the cutting motion with the hip rather than placing the full workload on ...

  • RedMax BC3401DL - page 15

    Under growth Heavy weeds Light weeds Grass BC3401DL BC4401DW Saw blade 6298-11313 10” 6298-15343 10” 6298-14343 10” PT104 4” PT100 6” 8-teeth blade 4-teeth blade Nylon line head CUTTER APPLICATION CHART ❲ 15 ❳ Optional Blade Usage ■ CHOOSE THE BLADE Choose a suitable recommended cutting attachment according to the object to be cut. ...

  • RedMax BC3401DL - page 16

    ❲ 16 ❳ Optional Blade Usage Change to the debris guard which is suitable for the metal blade. (OPT3) (1) Bolt : 3540-24130 x 2 pieces (2) Spring washer : 0290-20615 x 2 pieces (3) Clamp : 3541-24121 (4) Guard : 3541-24112 (5) Guard ass’y : 3541-24001 130~174 in-lbs TIGHTENING TORQUE: (14.7~19.6 N.m.) Change the loop handle to the J-handle for ...

  • RedMax BC3401DL - page 17

    Optional Blade Usage depth according to the condition of object. • If the grass or other object gets caught in the blade, or if the unit starts to shake or vibrate, turn off the engine and check the whole unit. Change the blade if it has been damaged. • Turn off the engine and make sure the blade has completely stop before checking the blade, a ...

  • RedMax BC3401DL - page 18

    ■ CONTROLLING BLADE BOUNCE • Kick out can cause serious personal injury. Carefully study this section. It is important that you understand what causes kick out, how you can reduce the chance of kick out and how you can remain in control of the unit if kick out does occur. 1. What causes kick out: • Kick out can occur when the moving blade con ...

  • RedMax BC3401DL - page 19

    Optional Blade Usage ❲ 19 ❳ OPT9 3. How you can maintain the best control: a. Keep a good, firm grip on the unit with both hands. A firm grip can help neutralize bounce. Keep your right and left hands completely around the respective handles. b. Keep both feet spread apart in a comfortable stance and yet braced for the possibility that the unit ...

  • RedMax BC3401DL - page 20

    ❲ 20 ❳ Maintenance • Always be sure to stop the engine before inspecting the brushcutter for problems or performing maintenance. • Never alter the brushcutter or take the engine apart. • When replacing parts, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax brushcutter. • ...

  • RedMax BC3401DL - page 21

    • Note that failing to do so may result in the engine catching on fire. ■ SPARK ARRESTER • The muffler is equipped with a spark arrester to prevent red hot carbon from flying out of the exhaust outlet. Periodically inspect and clean as necessary with a wire brush. In the State of California it is required by law (Section 4442 of the Californi ...

  • RedMax BC3401DL - page 22

    • If waste gets stuck and causes blockage around the intake air cooling vent or between the cylinder fins, it may cause the engine to overheat, and that in turn may cause mechanical failure on the part of the brushcutter. ■ PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, and wip ...

  • RedMax BC3401DL - page 23

    ❲ 23 ❳ Storage • Aged fuel is one of major causes of engine starting failure. Before storing the unit, empty the fuel tank and run the engine until it uses all the fuel left in the fuel line and the carburetor. Store the unit indoor taking necessary measures for rust prevention. ...

  • RedMax BC3401DL - page 24

    ❲ 24 ❳ Specifications ■ BC3401DL Overall size(LxWxH) ····················································· 67.7x12.6x13.6(in) / 1720x320x345(mm) Dry weight w/o acc. ······························································· ...

  • RedMax BC3401DL - page 25

    Parts List NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model name and the se ...

  • RedMax BC3401DL - page 26

    Parts List ❲ 26 ❳ Fig.1 DRIVE UNIT BC3401DL (S/N 200101 and up) ...

  • RedMax BC3401DL - page 27

    Fig.1 DRIVE UNIT BC3401DL (S/N 200101 and up) Key# Description Part Number Q'ty 1 HOUSING 4050-11110 1 2 CAP 4050-11150 1 3 JOINT 4050-11210 1 4 ABSORBER-F 4050-11250 1 5 ABSORBER-R 4050-11260 1 6 BOLT 01252-30530 4 7 BOLT 01252-30630 1 8 BOLT 01252-30510 1 9 DRUM, clutch 4050-11311 1 10 BEARING 06004-06202 1 11 SNAPRING 04065-03515 1 12 SNAPR ...

  • RedMax BC3401DL - page 28

    Fig.2 ENGINE UNIT BC3401DL (S/N 200101 and up) ❲ 28 ❳ Parts List ...

  • RedMax BC3401DL - page 29

    ❲ 29 ❳ Fig.2 ENGINE UNIT BC3401DL (S/N 200101 and up) Key# Description Part Number Q'ty 1 CYLINDER T1151-12110 1 2 BOLT 1850-12130 4 3 GASKET, base 4500-13120 1 4 CRANKCASE COMP. 4500-21101 1 5 • PIN 2629-21130 3 6 GUARD 4500-22110 1 7 SCREW 0263-90514 1 8 GASKET, case 4500-21140 1 9 BEARING 06030-06201 2 10 OIL SEAL 4810-21210 1 11 OIL ...

  • RedMax BC3401DL - page 30

    Parts List ❲ 30 ❳ Fig.3 DRIVE UNIT BC4401DW (S/N 200101 and up) ...

  • RedMax BC3401DL - page 31

    Fig.3 DRIVE UNIT BC4401DW (S/N 200101 and up) Key# Description Part Number Q'ty 1 HOUSING 4050-11110 1 2 CAP 4050-11150 1 3 JOINT 4050-11210 1 4 ABSORBER-F 4050-11250 1 5 ABSORBER-R 4050-11260 1 6 BOLT 01252-30530 4 7 BOLT 01252-30630 1 8 BOLT 01252-30510 1 9 DRUM, clutch 4050-11311 1 10 BEARING 06004-06202 1 11 SNAPRING 04065-03515 1 12 SNAPR ...

  • RedMax BC3401DL - page 32

    Fig.4 ENGINE UNIT BC4401DW (S/N 200101 and up) ❲ 32 ❳ Parts List ...

  • RedMax BC3401DL - page 33

    ❲ 33 ❳ Fig.4 ENGINE UNIT BC4401DW (S/N 200101 and up) Key# Description Part Number Q'ty 1 CYLINDER 4500-12110 1 2 BOLT 1850-12130 4 3 GASKET, base 4500-13120 1 4 CRANKCASE COMP. 4500-21101 1 5 • PIN 2629-21130 3 6 GUARD 4500-22110 1 7 SCREW 0263-90514 1 8 GASKET, case 4500-21140 1 9 BEARING 06030-06201 2 10 OIL SEAL 4810-21210 1 11 OIL S ...

  • RedMax BC3401DL - page 34

    THE CALIFORNIA AIR RESOURCES BOARD AND KOMATSU ZENOAH Co. ARE PLEASED TO EXPLAIN THE EMISSION CONTROL SYSTEM WARRANTY ON YOUR 1995 AND LATER LAWN AND GARDEN EQUIPMENT ENGINE. IN CALIFORNIA, NEW UTILITY AND LAWN AND GARDEN EQUIPMENT ENGINES MUST BE DESIGNED, BUILT AND EQUIPPED TO MEET THE STATE'S STRINGENT ANTI-SMOG STANDARDS. KOMATSU ZENOAH Co ...

  • RedMax BC3401DL - page 35

    EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. EMISSION-RELATED PARTS ARE: TH ...

  • RedMax BC3401DL - page 36

    Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage défectueux ...

  • RedMax BC3401DL - page 37

    EMISSION CONTROL LABEL BC3401DL KOMA TSU ZENOAH CO. MADE IN JAP AN IMPORT ANT ENGINE INFORMA TION THIS ENGINE CONFORMS T O US EP A PH1 FOR SMALL OFF-ROAD ENGINES. ENGINE F AMIL Y : 1KZXS.0344UV ;EM ENGINE DISPLACEMENT : 33.6cc REFER T O OWNER'S MANUMAL FOR MAINTE- NANCE SPECIFICA TIONS AND ADJUSTMENTS. MANUF ACTURED  G34L TYPE DE MOTEUR : 1 ...

  • RedMax BC3401DL - page 38

    KOMA TSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093  © Printed in Japan ...

Manufacturer RedMax Category Brush Cutter

Documents that we receive from a manufacturer of a RedMax BC3401DL can be divided into several groups. They are, among others:
- RedMax technical drawings
- BC3401DL manuals
- RedMax product data sheets
- information booklets
- or energy labels RedMax BC3401DL
All of them are important, but the most important information from the point of view of use of the device are in the user manual RedMax BC3401DL.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals RedMax BC3401DL, service manual, brief instructions and user manuals RedMax BC3401DL. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product RedMax BC3401DL.

Similar manuals

A complete manual for the device RedMax BC3401DL, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use RedMax BC3401DL by users. Manuals are usually written by a technical writer, but in a language understandable to all users of RedMax BC3401DL.

A complete RedMax manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual RedMax BC3401DL - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the RedMax BC3401DL, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the RedMax BC3401DL, that we can find in the current document
3. Tips how to use the basic functions of the device RedMax BC3401DL - which should help us in our first steps of using RedMax BC3401DL
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with RedMax BC3401DL
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of RedMax BC3401DL in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning RedMax BC3401DL?

Use the form below

If you did not solve your problem by using a manual RedMax BC3401DL, ask a question using the form below. If a user had a similar problem with RedMax BC3401DL it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)