Manual Hearth and Home Technologies SMART-BATT-II

12 pages 0.35 mb
Download

Go to site of 12

Summary
  • Hearth and Home Technologies SMART-BATT-II - page 1

    1 Printed in China Copyright 2006, Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 5504 100-909 G 12 /06 SMART -BA TT -II Remote Control Kit s - Installation and Operating Instructions - INTRODUCTION The remote control system can be operated thermostati- cally or manually from the transmitter . The system oper- ates o ...

  • Hearth and Home Technologies SMART-BATT-II - page 2

    2 RECEIVER WIRING INSTRUCTIONS Incorrect wiring connections WILL cause damage to the gas valve or electronic module operating the gas appliance and may also damage the remote receiver . Make sure the remote receiver switch is in the OFF position. Use 18 gauge stranded wires for connec- tions between the terminal wiring block on the milli- volt gas ...

  • Hearth and Home Technologies SMART-BATT-II - page 3

    3 Figure 4. Millivolt with Rocker Switch and Receiver Figure 5. Millivolt with 3 Wire If your fireplace is wired like Figure 3 find the leads on back of the switch marked “For use with remote or wall switch only” and take the leads and plug them into wire lead on remote receiver box (see Figure 4). 3-WIRE ASSE MBL Y PIE ZO RED WHI T E PILO T TH ...

  • Hearth and Home Technologies SMART-BATT-II - page 4

    4 Figure 6. Millivolt with Receiver Figure 7. Intermittent Pilot Ignition (IPI) Wiring Diagram IGNITION MODULE 3 V AC GRN ORG INTE RMITTE NT PIL OT IGNITOR ORG WHT VA LV E PIGGYBACK ON/OFF SWIT CH BRN BRN TRANSFORMER 3 V AC WHITE WIRE CAN BE PLUGGED INTO ANY OF #1- #5 L OCA TI ON S ON THE NEUTRAL SIDE BLACK WIRE CAN BE PLUGGED INT O A NY OF #1 - #5 ...

  • Hearth and Home Technologies SMART-BATT-II - page 5

    5 Figure 8. Intermittent Pilot Ignition (IPI) Wiring Diagram If your fireplace look like Figure 7 find the leads on the back of switch marked “For use with remote or wall switch only”. T ake the leads and plus them into wire leads on remote receiver box (see Figure 8). ON/ OFF SLI D E SW ITCH BLAC K RE D BA TTER Y P ACK PI GGY BAC K ON/O FF S W ...

  • Hearth and Home Technologies SMART-BATT-II - page 6

    6 Figure 9. If your fireplace looks like Figure 9 remove the 3-wire off the jumper wire by unplugging the spade from jumper wire. Install the jumper wire on the wire as shown see Figure 10. Then install one of the leads from the remote receiver onto the valve and other wire into the lead on the jumper wire. Figure 10. B L A C K R E D BA T TERY P A ...

  • Hearth and Home Technologies SMART-BATT-II - page 7

    7 NOTE: The remote receiver houses the microprocessor that responds to commands from the transmitter to control sys- tem operation. It emits one beep when it receives an ON or OFF command manually , but no beep when cycling on and off automatically in THERMO mode. The remote receiver has a 3-position slide switch: OFF/RE- MOTE/ON (see Figure 1 1). ...

  • Hearth and Home Technologies SMART-BATT-II - page 8

    8 MA TCHING SECURITY CODES It may be necessary to program the remote receiver to the security code of the transmitter upon initial use, if batteries are replaced, or if a replacement transmitter is purchased from your dealer . T o program the remote receiver: 1. Set the slide button on the receiver to the REMOTE position. 2. Push the LEARN button ( ...

  • Hearth and Home Technologies SMART-BATT-II - page 9

    9 SE TTIN G BUTTO N Figure 13. Setting Button/Child Proof Lockout Setting 0 F/ 0 C Scale The factory setting for temperature is degrees Fahrenheit ( 0 F). T o change this setting to degrees Centigrade ( 0 C): 1. Remove the battery cover on the back of the transmitter and locate the “setting button” at the top center of bat- tery compartment (se ...

  • Hearth and Home Technologies SMART-BATT-II - page 10

    10 TRANSMITTER SAFETY FEA TURES It is recommended that the TRANSMITTERS always be lo- cated within a 20 foot operating range of the fireplace, pref- erably in the same room in which the fireplace system is located. The TRANSMITTER features several safety features that alert the user when the TRANSMITTER is placed out- side the 20 foot normal operat ...

  • Hearth and Home Technologies SMART-BATT-II - page 11

    11 4. Then press the MODE button on the transmitter to change the system to ON. The spark electrode should begin sparking to ignite the pilot. After the pilot is lit, the main gas valve should open and the main gas flame should ignite. 5. Press the MODE button on the transmitter to OFF . The main gas flame and pilot flame should BOTH extinguish. 6. ...

  • Hearth and Home Technologies SMART-BATT-II - page 12

    12 Limited W arranty This REMOTE CONTROL SYSTEM is warranted for 12 months from the date of purchase or installation to the original purchaser to be free from defects in mate- rials and workmanship. Damage to the SYSTEM caused by accident, misuse, abuse, or installation error whether performed by a contractor , service com- pany , or owner , is not ...

Manufacturer Hearth and Home Technologies Category Universal Remote

Documents that we receive from a manufacturer of a Hearth and Home Technologies SMART-BATT-II can be divided into several groups. They are, among others:
- Hearth and Home Technologies technical drawings
- SMART-BATT-II manuals
- Hearth and Home Technologies product data sheets
- information booklets
- or energy labels Hearth and Home Technologies SMART-BATT-II
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hearth and Home Technologies SMART-BATT-II.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hearth and Home Technologies SMART-BATT-II, service manual, brief instructions and user manuals Hearth and Home Technologies SMART-BATT-II. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hearth and Home Technologies SMART-BATT-II.

A complete manual for the device Hearth and Home Technologies SMART-BATT-II, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hearth and Home Technologies SMART-BATT-II by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hearth and Home Technologies SMART-BATT-II.

A complete Hearth and Home Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hearth and Home Technologies SMART-BATT-II - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hearth and Home Technologies SMART-BATT-II, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hearth and Home Technologies SMART-BATT-II, that we can find in the current document
3. Tips how to use the basic functions of the device Hearth and Home Technologies SMART-BATT-II - which should help us in our first steps of using Hearth and Home Technologies SMART-BATT-II
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hearth and Home Technologies SMART-BATT-II
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hearth and Home Technologies SMART-BATT-II in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hearth and Home Technologies SMART-BATT-II?

Use the form below

If you did not solve your problem by using a manual Hearth and Home Technologies SMART-BATT-II, ask a question using the form below. If a user had a similar problem with Hearth and Home Technologies SMART-BATT-II it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)