Manual Craftsman 917.28746

18 pages 3.09 mb
Download

Go to site of 18

Summary
  • Craftsman 917.28746 - page 1

    @SearsBrands, l.l..C For answers to your questions about this product, Call: 1-800-659-5917 Sears Craftsman Help Line 5 am - 5 pm,Mon - Sat This product has a low emission engine which operates differently from previously built engines. Before you start the engine, read and understand this Owner's Manual. w CRAFTSMAN- GARDEN TRACTOR 26.0 HR 54 ...

  • Craftsman 917.28746 - page 2

    TABLE OF CONTENTS SAFETY RULES WARRANTY LIMITED WARRANTY ON CRAFTSMAN TRACTOR AND BATTERY 2-YEAR ON TRACTOR When used and maintained according to the operator's manual instructions; if this tractor fails due to a defect in material or workmanship within two years from the date of pur- chase, call 1-800-4-MY-HOME@ to arrange for free repair. Du ...

  • Craftsman 917.28746 - page 3

    SAFETY RULES SAFETY RULES • Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel . spillage and remove any fuel-soaked debris. Allow machine to cool before storing. • If you strike a foreign object, stop and inspect the machine. Repair, if neces- sary, before restarting. Never make any adjustments or repairs with the ...

  • Craftsman 917.28746 - page 4

    (1) 1-1/40.0. Washer @ (1) Locknut 3/8-16 Slope Sheet ~ (2) Rear Lift Link Assemblies Mower Install Sheet Mower Front Wheel Mower (2) Keys @ (1) 3/4 0.0. Washers ~ (2) Small Retainer Springs - 5/16 UNASSEMBLED PARTS (1) Whee! (i) ~i"'---'. (1) Shoulder Bolt (5) Large Retainer Springs - 7/16 (5) 1-3/16 0.0. Washers ~ (1) Oil Drain Tub ...

  • Craftsman 917.28746 - page 5

    - Pivot bar towards you and insert oth- er end of bar into hole in rear mower bracket (D). Move mower as needed to insert bar. - Secure with washer and retainer spring as shown. A '-" NOTE: Be sure mower side suspension arms (A) are pointing forward before slid- ing mower under tractor. 4. Slide mower under tractor until it is centered un ...

  • Craftsman 917.28746 - page 6

    II .ICHECKLIST Before you operate your new tractor, we wish to assure that you receive the best performance and satisfaction from this Quality Product. Please review the following checklist: ~ All assembly instructions have been completed. ~ No remaining loose parts in carton. ~ Battery is properly prepared and charged. . ~ Seat is adjusted comfort ...

  • Craftsman 917.28746 - page 7

    OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. ...

  • Craftsman 917.28746 - page 8

    TO ADJUST MOWER CUTTING HEIGHT The position of the attachment lift lever (A) determines the cutting height. • Put attachment lift lever in desired cut- ting height slot. • Slide pointer tab (T) to desired cutting height as a reminder for next time you mow. The cutting height range is approxi- mately 1" to 4". The heights are mea- sure ...

  • Craftsman 917.28746 - page 9

    the attachment engaged. Do not mow in reverse unless absolutely necessary. USING THE REVERSE OPERATION SYSTEM - Only use if you are certain no children or other bystanders will enter the mowing area. 1. Depress brake pedal all the way down. 2. With engine running, turn ignition key counterclockwise to"ROS "ON" posi- tion. 3. Look dow ...

  • Craftsman 917.28746 - page 10

    4. Move throttle control to fast position 5. Pull choke control out for a cold engine .start attempt. For a warm engine start attempt the choke control may not be needed. NOTE: Before starting, read the warm and cold starting procedures below. 6. Insert key into ignition and tum key clockwise to start position and release key as soon as engine star ...

  • Craftsman 917.28746 - page 11

    MAINTENANCE ROS "ON" Position • When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine. BLADE CARE For best results mower blades must be sharp. Replace worn, bent or damaged blades. A CAUTIO ...

  • Craftsman 917.28746 - page 12

    Oil Drain Valve Change the oil after every 50 hours of op- eration or at least once a year if the tractor is not used for 50 hours in one year. Check the crankcase oil level before start- ing the engine and after each eight (8) hours of operation. TO CHANGE ENGINE OIL Determine temperature range expected before oil change. All oil must meet API ser ...

  • Craftsman 917.28746 - page 13

    A CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth. 2. Raise mower to its highest position. 3. At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides. ~1~r1J#E • If front tip of blade is not 1/8&q ...

  • Craftsman 917.28746 - page 14

    Loosen jam nut A first NOTE: Each full turn of the adjustment nut will change mower height about 1/8". • Recheck measurements, adjust if nec- essary until front tip of blade is 1/8" to 1/2" lower than the rear tip. • Hold adjustment nut in position with wrench and tighten jam nut securely . against adjustment nut. C-. 26 TO REPLA ...

  • Craftsman 917.28746 - page 15

    TO CHECK BRAKE If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. You may also check brake by: 1. Park tractor on alevel, dry concrete or paved surface, depress clutch/brake pedal all the way down and engage parking brake. 2. Disengage transmis ...

  • Craftsman 917.28746 - page 16

    STORAGE Immediately prepare your tractor for stor- age at the end of the season or if the trac- t~.r will not be used for 30 days or more. aWARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. TRACTOR When tractor is to be ...

  • Craftsman 917.28746 - page 17

    TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE CORRECTION Loss of poWer 6. Faulty spark plug. 6. Clean and regap or change (continued) spark plug. 7. Dirty fuel filter. 7. Replace fuel filter. 8. Stale or dirty fuel. 8. Empty fuel tank and refill tank with fresh, clean gasoline. 9. Wat ...

  • Craftsman 917.28746 - page 18

    SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION - - - A WARNING: To avoid serious Injury, operate your tractor up and down the face of slopes, never across the face. Po not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this p ...

Manufacturer Craftsman Category Lawn Mower

Documents that we receive from a manufacturer of a Craftsman 917.28746 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 917.28746 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 917.28746
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 917.28746.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 917.28746, service manual, brief instructions and user manuals Craftsman 917.28746. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 917.28746.

A complete manual for the device Craftsman 917.28746, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 917.28746 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 917.28746.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 917.28746 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 917.28746, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 917.28746, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 917.28746 - which should help us in our first steps of using Craftsman 917.28746
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 917.28746
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 917.28746 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 917.28746?

Use the form below

If you did not solve your problem by using a manual Craftsman 917.28746, ask a question using the form below. If a user had a similar problem with Craftsman 917.28746 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)