-
Dimplex WRCPF-KIT - page 1
Owner ’ s Manual Model WRCPF-KIT 72091 10100R03 IMPORT ANT SAFETY INFORMA TION: Always read this manual rst before attempting to install or use this device. For your safety , always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage. T o view the full line of Dimplex products ...
-
Dimplex WRCPF-KIT - page 2
2 www .dimplex.com T able of Contents ! NOTE: Procedures and techniques that are considered important enough to emphasize. CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the equipment. W ARNING: Procedures and techniques which, if not carefully followed, will expose the user to the risk of re, s ...
-
Dimplex WRCPF-KIT - page 3
3 W elcome & Congratulations Thank you and congratulations for choosing to purchase a W all Switch Remote Control Kit from Dimplex, the world leader in electric replaces. Please carefully read and save these instructions. CAUTION: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions ...
-
Dimplex WRCPF-KIT - page 4
4 www .dimplex.com Product Overview The W all Switch Remote Control Kit is designed to work with the following Dimplex electric replaces: BF33STP • BF33DXP • BF39STP • BF39DXP • BF45DXP • BFSL33 • BLF50 • DF3033ST • DFG3033BLK • For the BF units, mentioned above, follow the Remote Receiver control installation instructions star ...
-
Dimplex WRCPF-KIT - page 5
5 Receiver Installation (BF units only) Open steel curtain (remove 1. glass doors if applicable). Remove two (2) screws on l og 2. grate and remove log grate (Figure 1). Locate and remove the two (2) 4. screws on the manual control bracket (Figure 3). Remove the bracket. Locate and depress the 5. mounting tabs on the plug connector and remove the m ...
-
Dimplex WRCPF-KIT - page 6
6 www .dimplex.com Locate the plastic 9-pin plug 6. in the bottom corner of the replace where the manual controls were plugged in to. Insert the plug connector from 7. the remote control bracket (Figure 4) into plastic plug inside the replace. ledge (Figure 2) and the logs are resting against the partially reective glass. Replace log grate ...
-
Dimplex WRCPF-KIT - page 7
7 W all Control Installation ! NOTE: All electrical w iring must comply with all national and local electrical codes and regulations. Always use a qualied and licensed electrician should you have any questions or concerns for all wiring work. ! NOTE: The W all Switch Remote Control is made to t standard Decora style faceplates. Due to materia ...
-
Dimplex WRCPF-KIT - page 8
8 www .dimplex.com Figure 5 Outer Housing Controller 2. Release the Controller from its Outer Housing by pushing the front face into the Outer Housing until you hear a click. This will release the push- lock latches and allow the Controller to be removed from the Outer Housing (Figure 5). 4. Replace the battery compartment cover . 5. Reinsert the C ...
-
Dimplex WRCPF-KIT - page 9
9 W all Control Installation to complete the installation and to blend the installation in with your choice of decor . Hard Wired Power Supplied Installation Before starting this installation, it is helpful to initialize the W all Switch Remote Control with your rebox (see Initialization section). Y ou should have the following items ready and p ...
-
Dimplex WRCPF-KIT - page 10
10 www .dimplex.com W all Control Installation 1. Unpack the W all Switch Remote Control and all hardware from its package. 2. Release the Controller from its Outer Housing by pushing the front face into the Outer Housing until you hear a click. This will release the push- lock latches and allow the Controller to be removed from the Outer Housing ( ...
-
Dimplex WRCPF-KIT - page 11
11 W all Control Installation Figure 12 Controller Outer Housing Figure 13 Locking Screw Option (Figure 14) T o prevent tampering, damage, and theft, it is suggested to install the locking screws. Once installed, the locking screws will prevent the Controller from being released from the Outer Housing without being removed rst from the device bo ...
-
Dimplex WRCPF-KIT - page 12
12 www .dimplex.com W all Control Installation Figure 15 Ensure each of the two Controller lead wires are connected to separate Low V oltage 24V~ only wires. Low V oltage 24V~ power source ONL Y Controller wire leads Figure 16 Flat Head Screws (supplied) ...
-
Dimplex WRCPF-KIT - page 13
13 ! NOTE: Wire leads are not polarized due to the nature of this device. 9. Coil excess wiring to the back of the device box and insert the Controller and Outer Housing int o t he d evi ce box (Fi gur e 16 ). Fasten with two supplied at head screws. 10. Attach your choice of Decora style faceplate (not supplied) to complete the installation and ...
-
Dimplex WRCPF-KIT - page 14
14 www .dimplex.com Initialization After installation, locate the section which applies to your specic model of replace and follow the steps for remote control initialization and if required, re-initialization. Refer to your replace's owner's manual to locate manual or other controls as needed. BF Models Using the Included Receiv ...
-
Dimplex WRCPF-KIT - page 15
15 Initialization DF3033ST and DFG3033 Models 1. Ensure that power is supplied through main service panel. 2. Ensure the Main On/Off Switch located in the switch box on the replace in the upper right hand corner is in the On position (Figure 19A) . A B C Figure 19 DF3033ST / DFG3033 Manual controls 3. Set the 3 Position Manual Control (Figure 19 ...
-
Dimplex WRCPF-KIT - page 16
16 www .dimplex.com Operation A. On Button Pressing this button toggles sequentially through the three levels of the replace. Pressing once activates Level 1 - ame effect only , twice activates Level 2 - ame effect and Purire™, three times activates Level 3 - ame effect, Purire™ and heat. B. Off Button Pressing this button at ...
-
Dimplex WRCPF-KIT - page 17
17 Operation W all Switch Remote Control 1 3 5 2 4 6 7 9 11 8 10 12 13 14 1. Room T emperature 2. Set T emperature 3. Flame Effect 4. Purire™ 5. Heat Off Indicator 6. Function Lock Indicator 7. RF Code Function Indicator 8. Set T emperature Down 9. Set T emperature Up 10. Flame Off 1 1. Flame On 12. Purire™Off 13. Purire™ ...
-
Dimplex WRCPF-KIT - page 18
18 www .dimplex.com Operation 1. Room T emperature Displays current ambient temperature in the room. 2. Set T emperature Displays and controls the heater to the temperature at which the thermostat is currently set to. Press 8 to lower the thermostat and press 9 to raise the thermostat. Pressing both 8 and 9 together will toggle between Celsius and ...
-
Dimplex WRCPF-KIT - page 19
19 Operation 7. RF Code Function and Change Procedure In the event that the W all Switch Remote Control does not work properly with the receiver due to interference from additional wireless signals, this function will allow the RF code to be changed. T o enable this function, press 9 and 12 together . “ COD ” will appear on the display for v ...
-
Dimplex WRCPF-KIT - page 20
20 www .dimplex.com W arranty This Dimplex W all Switch Remote Control is warranted against defects in workmanship and materials for two years from date of sale. This warranty does not apply to damage from accident, misuse, or alteration, nor where the connected voltage is more that 5 % above the nameplate voltage, nor to equipment improperly insta ...
Do you have a question concerning Dimplex WRCPF-KIT?
Use the form below
If you did not solve your problem by using a manual Dimplex WRCPF-KIT, ask a question using the form below. If a user had a similar problem with Dimplex WRCPF-KIT it is likely that he will want to share the way to solve it.