English dropdown-ico

Manual Jet 719T WMH

20 pages 1.48 mb
Download

Go to site of 20

Summary
  • Jet 719T WMH - page 1

    Operating Instructions and Parts Manual Tilting Table Hollow Chisel Mortiser Model: 719T WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-2474002 Ph.: 800-274-6848 Revision A 03/04 www.wmhtoolgroup.com Copyright © WMH Tool Group ...

  • Jet 719T WMH - page 2

    2 This manual has been prepared for the owner and operators of a POWE RMATIC 719T Tilting Ta ble Hollow Chisel Mortiser. Its purpose, aside from ma chi ne operation, is to promote safety using accepte d operating and maintenance procedures. To obtain maxi mum life and efficien cy from your mortiser and to aid in using it safely, please read this ma ...

  • Jet 719T WMH - page 3

    3 Table of Contents Warranty and Service ........................................................................................................... ......................... 2 Table of Contents .............................................................................................................. ............................ 3 Warnings .... ...

  • Jet 719T WMH - page 4

    4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the m a chine and in this manual. Failure to comply with all of these warnings may cause seri ous injury. 3. Replace the warning labels if they become obscu red or removed. 4. This mortiser is designed a ...

  • Jet 719T WMH - page 5

    5 blahblahblah 21. Make your workshop child proof with padlocks , master switches or by removing starter keys. 22. Give your work undivided attention. Loo king aroun d, carrying on a conversation and “horse-play” are careless acts that can result in seriou s injury. 23. Maintain a balanced stance at all times so that you d o not fall or lean ag ...

  • Jet 719T WMH - page 6

    6 Introduction This manual is provided by POWE RMATIC covering the safe operation and mai ntenance procedures for a Model 719T Tilting Table Hollow Ch isel Mortiser. Th is manual contain s instructions on installation, safety precautions, general operating procedures, ma intenance instructions and parts breakdown. Thi s machine has been designed an ...

  • Jet 719T WMH - page 7

    7 Unpacking Remove mortiser and stand from the shipping ca rtons. Check for damage and ensure all part s are intact. Any damage should be reported immediately to your distributor and shippin g agent. Read the manu al thoroughly to familiarize y ourself with the correct assembly a nd maintenance procedures and proper safety precautions. Contents of ...

  • Jet 719T WMH - page 8

    8 Assembly Do not connect the machine to power source until c ompletely assembled. Read and understand the entire manual. Securing Machine to Stand The mortiser should be secured to the stand with four M8 x 45 hex cap screws and M8 lock washers (pro vided) using the holes in the base. Make sure there is en ough room on e ach side of the mortiser fo ...

  • Jet 719T WMH - page 9

    9 Installing Chisel and Bit Referring to Figure 3 : 1. Loosen the lock screw . 2. Insert the chisel bushing into the head with the hole facing forward to line up with the lock screw . Screw in the lock screw just enough so the screw extends into th e hole of the bushing , holding it in place. 3. Push the chisel up th rough the bushing , bringing it ...

  • Jet 719T WMH - page 10

    10 Electrical Power Connection Do not operate this machine in damp locations. A separate electrical circui t should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire ex tension cords whi ch have 3-prong grounding type plugs a nd ...

  • Jet 719T WMH - page 11

    11 Adjustments 90 ° Chisel to Worktable Calibration Referring to Figure 7: Place a square (E) so it rests a gainst the worktable (B) and chisel (A). If the chisel to table angle is 90 ° , no calibration is necessary. If calibration is required: 1. Loosen the bolt (C) that allows the tilting base to pivot. The tilting base is heavy. If raised, tak ...

  • Jet 719T WMH - page 12

    12 6. Reinstall the chisel bus hing (F) and se cure it loosely with the lock screw (E). 7. Reinstall the chisel and bit (refer to the Installing Chisel and Bit section ) . Depth Stop Rod Adjustment Referring to Figure 9: A depth stop rod (A) is provided to li mit the depth of the chisel. To adjust: 1. Loosen lock lever (B) and lower the dept h stop ...

  • Jet 719T WMH - page 13

    13 Chisel Parallel to Workpiece Referring to Figure 11: The chisel can be adjusted parallel to the workpiece as follows: 1. With the left handwheel (A), move the t able back far enough to insert the wo rkpiece (B) between the chisel (D) and fence . 2. Loosen the lock screw (C). This will allow the chisel to rotate. 3. Bring the table forward with t ...

  • Jet 719T WMH - page 14

    14 Do not have the chisel slot against the blind end of the mortise, as the chips will not be able to clear the chisel. This can cause ov erheating and possible breakage of chisel or bit. When cutting deep mortises, make the cut in several stages of approximately 1" each, to allow chips to clear. To prevent breakout at the back of the workpiec ...

  • Jet 719T WMH - page 15

    15 three turns of the cutter in a carpenter' s brace chuck should be en ough to sharpen th e chisel, as shown in Figure 16. Use a small, triangular, smooth file to reliev e the inner corners of the chi sel (Figure 17). Remove any burrs from the outsi de of the chisel with a fine oilstone. Lubrication All of the ball bearings are packed with gr ...

  • Jet 719T WMH - page 16

    16 719T Mortiser Parts List Index No. Part No. Description Size Qty ................. 2474002T ................. 719T Mortiser Assy (Items 1 thru 120) .............. ................................ ................. 1 1 ............... 719T-101 .................. Fixed Base ........................................................... .............. ...

  • Jet 719T WMH - page 17

    17 Index No. Part No. Description Size Qty 57 ............. 6294180 ................... C-Clip ................................................................... ................................................. 2 58 ............. 6294181 ................... Depth Setting Block ............................................. ...................... . ...

  • Jet 719T WMH - page 18

    18 Index No. Part No. Description Size Qty 114 ........... TS-1491021 ............. Hex Ca p Screw .................................................... M10 x 20 ................. ................. 4 115 ........... 719T-1115................ Tilt ing Bracket ...................................................... ................... ................. ...

  • Jet 719T WMH - page 19

    19 719T Mortiser Stand Parts List Index No. Part No. Description Size Qty ................. 6294235T ................. Stand Assembly (Items 1 thru 8).......................... ............................ ..................... 1 1 ............... 719T-201 .................. Stand .................................................................... ...

  • Jet 719T WMH - page 20

    20 Optional Accessories Index No. Part No. Description ................. 6294232 ................... Chuck Extension Adapto r Kit (Items 1 thru 3) ...... .................................. ................. 1 ............... 6294210 ................... Drill Adaptor Shaft ................................................ .................. ......... ...

Manufacturer Jet Category Drill

Documents that we receive from a manufacturer of a Jet 719T WMH can be divided into several groups. They are, among others:
- Jet technical drawings
- 719T WMH manuals
- Jet product data sheets
- information booklets
- or energy labels Jet 719T WMH
All of them are important, but the most important information from the point of view of use of the device are in the user manual Jet 719T WMH.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Jet 719T WMH, service manual, brief instructions and user manuals Jet 719T WMH. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Jet 719T WMH.

Similar manuals

A complete manual for the device Jet 719T WMH, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Jet 719T WMH by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Jet 719T WMH.

A complete Jet manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Jet 719T WMH - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Jet 719T WMH, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Jet 719T WMH, that we can find in the current document
3. Tips how to use the basic functions of the device Jet 719T WMH - which should help us in our first steps of using Jet 719T WMH
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Jet 719T WMH
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Jet 719T WMH in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Jet 719T WMH?

Use the form below

If you did not solve your problem by using a manual Jet 719T WMH, ask a question using the form below. If a user had a similar problem with Jet 719T WMH it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)