English dropdown-ico

Manual Global Machinery Company 1050W

14 pages 0.29 mb
Download

Go to site of 14

Summary
  • Global Machinery Company 1050W - page 1

    PRT ABLE 031219 ED12 DR INSTRUCTION MANU AL 1050W Pow ered Router T able • Melbourne • Perth • Auckland • Hong K ong • Shanghai • T aipei • New Y ork • V erona • London • P aris ...

  • Global Machinery Company 1050W - page 2

    Contents ...

  • Global Machinery Company 1050W - page 3

    Description of s ymbols The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use . W ear hearing protection. W ear eye protection. W ear breathing protection. Double insulated f or additional protection. Conforms to relevant standards f or electromagnetic compatibility. Speci ...

  • Global Machinery Company 1050W - page 4

    General safety instructions The tool must be used only for its prescribed purpose . Any use other than those mentioned in this Manual will be considered a case of misuse . The user and not the manufacturer shall be liable f or any damage or injury resulting from such cases of misuse . To use this tool properly , you must observe the safety regulati ...

  • Global Machinery Company 1050W - page 5

    15. A void unintentional starting. Always check that the switch is in the OFF position before plugging in the tool to the power supply. Do not carry a plugged in tool with your finger on the switch. 16. Stay alert. W atch what you are doing. Use common sense . Do not operate a power tool when you are tired. 17. Check f or damaged parts. Before usin ...

  • Global Machinery Company 1050W - page 6

    • Before using the tool to make a cut, switch on and let it run for a while . Watch for vibration or wobbling that could indicate an improperly installed bit. • Ta ke notice o f the direction of rotation of the bit and the direction of feed. • Always switch off and wait until the bit has come to a complete standstill before removing the work ...

  • Global Machinery Company 1050W - page 7

    Know y our product 1. T able 2. Rear fence 3. Infeed fence 4. Outfeed fence 5. Fence locking knobs 6. Guide block locking knobs 7. Dust extraction hood 8. Dust extraction port 9. On/Off switch 10. Mitre gauge 11. Mitre gauge locking knob 12. Spindle lock lever 13. V ariable speed dial 14. Height adjustment lock 7 15. Collet assembly cover 16. Colle ...

  • Global Machinery Company 1050W - page 8

    Installing and r emoving collets W arning. Always ensure the tool is switched off and the plug is removed from the power point before making any adjustments. When changing the collets or when changing bits, the height of the motor assembly should be raised to close to the maximum height to gain full access to the collet nut. 1. The powered router t ...

  • Global Machinery Company 1050W - page 9

    11. Replace the collet assembly cover in the following way: 11. The collet assembly cover locates in the centre of the height adjusting ring and is secured in place with two small screws. 11. The cover is usually fitted after the cutter has been installed, thus you need to select the cover which will pass over the cutter with the minimum of clearan ...

  • Global Machinery Company 1050W - page 10

    Ad justments A djusting the speed 1. Adjust the variable speed dial (9) to suit different material. The tool cuts quicker and smoother at different speeds and when working in different woods or in plastic or aluminium. 2. Adjust the variable speed dial to a higher number for f aster speed or to a lower number for slower speed. 3. Determine the opti ...

  • Global Machinery Company 1050W - page 11

    A djusting the fence for trimming 1. When trimming timber the material coming out on the left hand side (outfeed) (4) of the cutter will be thinner than the material being fed through on the right hand side (infeed) (3). 2. The left hand guide block will need to be adjusted to compensate for the thinner material. This will help support the material ...

  • Global Machinery Company 1050W - page 12

    A djusting the mitre gauge 1. The mitre gauge (10) slides horizontally along the table to allow for edging and mitre cuts in the work piece . 2. T o adjust the mitre gauge to the desired angle loosen the mitre gauge locking knob (11) and rotate the mitre gauge to the desired angle from 0° to 45°. 3. Tighten the mitre gauge locking knob (11). 4. F ...

  • Global Machinery Company 1050W - page 13

    Operation 1. Insert and secure the router bit. 2. Adjust the speed, depth o f cut, feather boards, fence alignment and mitre gauge as required. 3. Ensure you adjust the infeed fence (3) so that it supports the uncut material and the outfeed fence (4) so that it supports the cut material, compensating for the removed material if trimming. 4. Ensure ...

  • Global Machinery Company 1050W - page 14

    Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Type • GMC Product Code A GMC Service Engineer wil ...

Manufacturer Global Machinery Company Category Router

Documents that we receive from a manufacturer of a Global Machinery Company 1050W can be divided into several groups. They are, among others:
- Global Machinery Company technical drawings
- 1050W manuals
- Global Machinery Company product data sheets
- information booklets
- or energy labels Global Machinery Company 1050W
All of them are important, but the most important information from the point of view of use of the device are in the user manual Global Machinery Company 1050W.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Global Machinery Company 1050W, service manual, brief instructions and user manuals Global Machinery Company 1050W. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Global Machinery Company 1050W.

Similar manuals

A complete manual for the device Global Machinery Company 1050W, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Global Machinery Company 1050W by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Global Machinery Company 1050W.

A complete Global Machinery Company manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Global Machinery Company 1050W - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Global Machinery Company 1050W, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Global Machinery Company 1050W, that we can find in the current document
3. Tips how to use the basic functions of the device Global Machinery Company 1050W - which should help us in our first steps of using Global Machinery Company 1050W
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Global Machinery Company 1050W
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Global Machinery Company 1050W in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Global Machinery Company 1050W?

Use the form below

If you did not solve your problem by using a manual Global Machinery Company 1050W, ask a question using the form below. If a user had a similar problem with Global Machinery Company 1050W it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)