English dropdown-ico

Manual Kicker cx600.5

32 pages 1.37 mb
Download

Go to site of 32

Summary
  • Kicker cx600.5 - page 1

    CX MUL TI-CHANNEL AMPS CX600.5 Owner’s Manual | English Manual del Propietario | Español AMPLIFICADOR DEL LA SERIE CX.5 Benutzerhandbuch | Deutsch VERSTÄRKER DER CX.5-SERIE Manuel d’utilisation | Française AMPLIFICATEUR DE SÉRIE CX.5 CX Amplifiers 2012 CX 5-Channel Amp Rev F.indd 1 2012 CX 5-Channel Amp Rev F.indd 1 6/22/2012 3:08:42 PM 6/2 ...

  • Kicker cx600.5 - page 2

    2 CX.5-SERIES AMPLIFIERS OWNER’S MANUAL INST ALLA TION Mounting: Choose a structurally sound location to mount your KICKER amplifi er . Make sure there are no items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for the amplifi er . If possible, mount the amplifi er in th ...

  • Kicker cx600.5 - page 3

    3 Wiring: Disconnect the vehicle’ s battery to avoid an electrical short. Then, connect the ground wire to the amplifi er . Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid, metal area of the vehicle’ s chassis. Adding an additional ground wire of this same gauge (or larger) between the batt ...

  • Kicker cx600.5 - page 4

    4 POWER WIRING GND REM +12V 12V AMP1 AMP2 SUB L R S S L R battery external fuse remote turn-on (see page 6) bare-metal chassis ground bare-metal chassis ground  18” (45cm)  24” (60cm) Model External Fuse (sold separately) Power/Ground W ire KICKER W iring Kit CX600.5 1 x 80 Ampere 4 Gauge PK4, CK44, ZCK44 Install a fuse within 18” (45cm ...

  • Kicker cx600.5 - page 5

    5 CXRC REMOTE BASS INST ALLA TION (See page 6. CXRC not included.) back view AMP1 AMP2 SUB L R S S L R GND REM +12V FOUR CHANNEL OPERA TION with SUBWOOFER minimum impedance of 2 ohms per channel (AMP1, AMP2, and SUB channels) Surface-mount the CXRC remote using the supplied screws. Remote cable passes audio; do not run cable parallel to power wires ...

  • Kicker cx600.5 - page 6

    6 OPERA TION Automatic T ur n-On Selection: The CX series offers two different automatic turn-on modes; +12V and DC Offset. • Remote T urn-On: Run 18 gauge wire from the Remote T urn-On Lead on your source unit to the terminal labeled REM between the amplifi er ’ s positive and negative power terminals. This is the preferred automatic turn-on ...

  • Kicker cx600.5 - page 7

    7 TROUBLESHOOTING If your amplifi er does not appear to be working, check the obvious things fi rst such as blown fuses, poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There are Power (PWR) & Protection (PRT) LEDs on the side panel of your Kicker CX series amplifi er . Depending on the sta ...

  • Kicker cx600.5 - page 8

    8 KICKER will now provide a thr ee- year warranty with all CX-Series Amplifi er purchases paired with a qualifying KICKER Installation Kit* . This extends the standard warranty by an additional year . Amplifi er and Kit must be purchased from an Authorized KICKER Dealer . KICKER CX amplifi er success is currently at an unheard-of rate, making th ...

  • Kicker cx600.5 - page 9

    9 Modelo: CX600.5 Alimentación RMS, AMP1 y AMP2 @ 14.4V , 4  estéreo,  1% THD+N @ 14.4V , 2  estéreo,  1% THD+N @ 14.4V , 4  mono,  1% THD+N 40W x 4 75W x 4 150W x 2 Alimentación, SUB canal @ 14.4V , 2 Ω monofónico,  1.5% THD+N @ 14.4V , 4 Ω monofónico,  1.5% THD+N 300 x 1 150 x 1 Longitud | pulg. [mm] 14 [360] Altur ...

  • Kicker cx600.5 - page 10

    10 soporte de doble ranura tornillos hexagonales panel de fondo del amplifi cador Los Amplifi cadores CX de KICKER se pueden instalar verticalmente para ahorrar espacio. Use una llave hexagonal de 2,5mm (llave Allen) para afl ojar el panel de fondo, quite los soportes existentes, luego inserte y apriete los soportes de doble ranura al amplifi c ...

  • Kicker cx600.5 - page 11

    11 GND REM +12V 12V AMP1 AMP2 SUB L R S S L R batería fusible externo encendido a distancia (página 13) conexión a tierra  18” (45cm)  24” (60cm) Modelo Fusible Externo (no incluido) Cable de Alimentación y Conexión a T ierra Kit de cableado KICKER CX600.5 1 x 80A Calibre 4 PK4, CK44, ZCK44 Instale un fusible a menos de 18 plg. (45 c ...

  • Kicker cx600.5 - page 12

    12 CXRC CONTROL REMOTO DE BAJOS INST ALACIÓN (no incluido CXRC. V ea la página 13) AMP1 AMP2 SUB L R S S L R GND REM +12V FUNCIONAMIENTO POR CUA TRO CANALES CON SUBWOOFER impedancia mínima de 2 ohmios por canales (AMP1, AMP2, y SUB canales) vista desde atrás Para instalar en superfi cie el control remoto CXRC use los tornillos suministrados. C ...

  • Kicker cx600.5 - page 13

    13 señal de entrada FUNCIONAMIENTO Selección de Encendido Automático: El modelo CX le ofrece dos distintos modos de encendido automático; desvío a +12V y DC. • Encendido a Distancia: Instale cable calibre 18 desde el conductor de encendido a distancia de la unidad fuente hasta la terminal etiquetada REM entre las terminales de alimentación ...

  • Kicker cx600.5 - page 14

    14 RESOLUCIÓN DE PROBLEMAS Si su amplifi cador parece no estar funcionando, revise lo obvio primero: fusibles quemados, conexiones malas o incorrectas, posición incorrecta de los selectores de crossover y amplifi cación, etc. Su amplifi cador modelo CX de KICKER cuenta con los LED de protección (PRT) y de encendido (PWR) en el panel de alime ...

  • Kicker cx600.5 - page 15

    15 CX600.5 40 x 4 @ 4 ohmios (20Hz–20,000Hz) Relación de Señal a Ruido -75dB CEA-2006B (ref: 1W , ponderado en A) 150 x 1 @ 4 ohmios (25Hz–200Hz) Relación de Señal a Ruido -75dB CEA-2006B (ref: 1W , ponderado en A) 14.4VCC, 1% THD, CEA-2006B (W) 2012 CX 5-Channel Amp Rev F.indd 15 2012 CX 5-Channel Amp Rev F.indd 15 6/22/2012 3:08:56 PM 6/2 ...

  • Kicker cx600.5 - page 16

    16 Modell: CX600.5 RMS-Leistung, AMP1 und AMP2 @ 14.4V , 4 Ω stereo,  1% Gesamtklirrfaktor @ 14.4V , 2 Ω stereo,  1% Gesamtklirrfaktor @ 14.4V , 4 Ω mono,  1% Gesamtklirrfaktor 40W x 4 75W x 4 150W x 2 RMS-Leistung, SUB kanal @ 14.4V , 2 Ω mono,  1,5% Gesamtklirrfaktor @ 14.4V , 4 Ω mono,  1,5% Gesamtklirrfaktor 300 x 1 150 x 1 ...

  • Kicker cx600.5 - page 17

    17 Anschluss: T rennen Sie den Anschluss der Fahrzeugbatterie, um einen Kurzschluss zu vermeiden. Schließen Sie dann das Massekabel an den V erstärker an. Verwenden Sie ein kurzes Erdungskabel (maximal 60 cm) und schließen Sie es an eine lack- oder korrosionsfreie Metallstelle an der Fahrzeugkarosserie an. Es wird auch empfohlen, ein weiteres Ma ...

  • Kicker cx600.5 - page 18

    18 GND REM +12V 12V AMP1 AMP2 SUB L R S S L R Batterie Ferneinschaltung (Seite 20) Masse  18” (45cm)  24” (60cm) externe Sicherung Modell Externe Sicherung (nicht inbegriffen) Massekabel KICKER V erkabelungssatz CX600.5 1 x 80 Ampere 4 GA PK4, CK44, ZCK44 Installieren Sie in maximal 45 cm Entfernung von der Batterie eine Sicherung in Reih ...

  • Kicker cx600.5 - page 19

    19 CXRC BASSPEGEL-FERNBEDIENUNG INST ALLA TION (CXRC nicht inbegriffen. Siehe Seite 20.) AMP1 AMP2 SUB L R S S L R GND REM +12V VIERKANALBETRIEB MIT SUBWOOFER Minimal impedanz von 2 Ohm pro Kanal (AMP1, AMP2, und SUB Kanäle) Stecken Sie das mitgelieferte 1/8 Zoll [3.5mm] Patchkabel in den CXRC- Remote-Regler und in die “Remote-Bass”-Steckerbuc ...

  • Kicker cx600.5 - page 20

    20 BETRIEB Automatische Einschaltung: Die CX-Serie umfasst zwei automatische Einschaltmodi: +12V und DC Offset. • Remote T urn-On (Ferneinschaltung): Verlegen Sie 18 GA-Kabel von der Ferneinschaltung an Ihrem Autoradio zum REM-T erminal zwischen den positiven und negativen Stromanschlüssen des Verstärkers. Das ist die bevorzugte automatische Ei ...

  • Kicker cx600.5 - page 21

    21 PROBLEMBEHEBUNG Wenn der V erstärker nicht zu funktionieren scheint, sollten Sie zuerst offensichtliche Faktoren prüfen, wie durchgebrannte Sicherungen, schlechte oder fehlerhafte V erkabelung, inkorrekte Einstellung des Crossover- Schalters und der V erstärkungsregler etc. Am seitlichen Einschaltfeld des Kicker CX-Verstärkers befi nden sic ...

  • Kicker cx600.5 - page 22

    22 CX600.5 40 x 4 @ 4 ohms (20Hz–20,000Hz) Rauschabstand -75dB CEA-2006B (ref: 1W , A-gewichtet) 150 x 1 @ 4 ohms (25Hz–200Hz) Rauschabstand -75dB CEA-2006B (ref: 1W , A-gewichtet) 14.4V GS, 1% Klirrfaktor , CEA-2006B (Watts) 2012 CX 5-Channel Amp Rev F.indd 22 2012 CX 5-Channel Amp Rev F.indd 22 6/22/2012 3:09:00 PM 6/22/2012 3:09:00 PM ...

  • Kicker cx600.5 - page 23

    23 Modèle: CX600.5 Puissance Effi cace @ 14.4V , 4 Ω stéréo,  1% THD+N @ 14.4V , 2 Ω stéréo,  1% THD+N @ 14.4V , 4 Ω mono,  1% THD+N 40W x 4 75W x 4 150W x 2 Puissance Effi cace @ 14.4V , 2 Ω mono,  1,5% THD+N @ 14.4V , 4 Ω mono,  1,5% THD+N 300 x 1 150 x 1 Longueur | pouces [mm] 14 [360] Hauteur | pouces [mm] 2-3/8 [60] ...

  • Kicker cx600.5 - page 24

    24 vis hexagonales panneau d’extrémité de l’amplifi cateur bride à double fente Câblage: Débranchez la batterie du véhicule pour éviter un court-circuit. Ensuite, raccordez le fi l de masse à l’amplifi cateur . Le fi l de masse doit être le plus court possible, de 60 cm (24 po) maximum. Raccordez-le à une partie métallique soli ...

  • Kicker cx600.5 - page 25

    25 Modèle Fusible Externe (non inclus) Fil de Masse / Alimentation KICKER Kit de câblage CX600.5 1 x 80 Ampères Calibre 4 PK4, CK44, ZCK44 GND REM +12V 12V AMP1 AMP2 SUB L R S S L R Batterie Mise sous tension à distance (page 27) Masse  18” (45cm)  24” (60cm) Installez un fusible dans un rayon de 45 cm (18 po) de la batterie directeme ...

  • Kicker cx600.5 - page 26

    26 CXRC TÉLÉCOMMANDE DU NIVEAU DES GRA VES INST ALLA TION (CXRC non inclus. V oir page 27.) AMP1 AMP2 SUB L R S S L R GND REM +12V FONCTIONNEMENT À QUA TRE CANAUX A VEC CAISSON DE GRA VES impédance minimum de 2 ohms par canal (AMP1, AMP2, et le SUB canaux Installez la télécommande CXRC en surface en utilisant les vis fournies. Câble de la t? ...

  • Kicker cx600.5 - page 27

    27 UTILISA TION Sélection de Mise sous T ension Automatique : La série CX propose deux modes d’allumage automatique différents ; +12 V et décalage en continu. • Mise sous T ension à Distance : Faites passer un fi l de calibre 18 à partir du fi l de mise sous tension à distance sur votre appareil source jusqu’à la borne étiquetée R ...

  • Kicker cx600.5 - page 28

    28 EN CAS DE DIFFICUL TÉ Si votre amplifi cateur ne marche pas, vérifi ez d’abord les possibilités évidentes comme les fusibles sautés, les branchements incorrects ou desserrés, le mauvais réglage des commandes de gain et du commutateur du fi ltre, etc. Une DEL de protection électrique est située sur le panneau latéral de votre ampli ...

  • Kicker cx600.5 - page 29

    29 CX600.5 40 x 4 @ 4 ohms (20Hz–20,000Hz) Rapport Signal sur Bruit -75dB CEA-2006B (ref: 1W , pondéré A) 150 x 1 @ 4 ohms (20Hz–200Hz) Rapport Signal sur Bruit -75dB CEA-2006B (ref: 1W , pondéré A) 14.4V C.C., 1% de Distorsion Harmonique T otale, CEA-2006B (W) 2012 CX 5-Channel Amp Rev F.indd 29 2012 CX 5-Channel Amp Rev F.indd 29 6/22/201 ...

  • Kicker cx600.5 - page 30

    30 ELECTRONICS LIMITED W ARRANTY When purchased from an Authorized KICKER Dealer , KICKER warrants this product to be free from defects in material and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase with receipt. If this product is identifi ed as “Refurbished” or “B Goods”, the warranty is limited ...

  • Kicker cx600.5 - page 31

    31 P .O. Box 459 • Stillwater , Oklahoma 74076 • USA • (405) 624–8510 INTERNA TIONAL W ARRANTY Contact your International KICKER dealer or distributor concerning specifi c procedures for your country’s warranty policies. WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! T urning up a ...

  • Kicker cx600.5 - page 32

    ©2012 Stillwater Designs 2012 CX 5-Channel Amp Rev F.indd 32 2012 CX 5-Channel Amp Rev F.indd 32 6/22/2012 3:09:05 PM 6/22/2012 3:09:05 PM ...

Manufacturer Kicker Category Car Amplifier

Documents that we receive from a manufacturer of a Kicker cx600.5 can be divided into several groups. They are, among others:
- Kicker technical drawings
- cx600.5 manuals
- Kicker product data sheets
- information booklets
- or energy labels Kicker cx600.5
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kicker cx600.5.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kicker cx600.5, service manual, brief instructions and user manuals Kicker cx600.5. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kicker cx600.5.

Similar manuals

A complete manual for the device Kicker cx600.5, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kicker cx600.5 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kicker cx600.5.

A complete Kicker manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kicker cx600.5 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kicker cx600.5, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kicker cx600.5, that we can find in the current document
3. Tips how to use the basic functions of the device Kicker cx600.5 - which should help us in our first steps of using Kicker cx600.5
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kicker cx600.5
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kicker cx600.5 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kicker cx600.5?

Use the form below

If you did not solve your problem by using a manual Kicker cx600.5, ask a question using the form below. If a user had a similar problem with Kicker cx600.5 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)