Manual Husqvarna DM 340

16 pages 0.74 mb
Download

Go to site of 16

Summary
  • Husqvarna DM 340 - page 1

    G G G G B B B B E E E E S S S S P P P P T T T T G G G G R R R R DM 340 GB ES PT GR Oper ator’ s manual Please read the operator’ s manual car efully and make sure y ou understand the instructions before using the machine. Manual de instrucciones Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar ...

  • Husqvarna DM 340 - page 2

    2 – English KEY T O SYMBOLS Symbols on the machine: W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or fatal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • Approv ...

  • Husqvarna DM 340 - page 3

    English – 3 CONTENTS Contents KEY T O SYMBOLS Symbols on the machine: ............................................. 2 Symbols in the operator’ s manual: ............................... 2 CONTENTS Contents ...................................................................... 3 PRESENT A TION DM 340 .............................................. ...

  • Husqvarna DM 340 - page 4

    4 – English PRESENT A TION DM 340 It is our wish that you will be satisfied with y our product and that it will be your companion f or a long time. Think of this operator ′ s manual as a v aluable document. By follo wing its ′ content (using, ser vice, maintenance etc) the lif e span and the second-hand value of the machine can be e xtended. ...

  • Husqvarna DM 340 - page 5

    English – 5 WHA T IS WHA T? What is what on the drilling machine? 1 Drill spindle 2 Gearbo x and motor module 3 Carr ying handle 4 Gear knob 5 Quick mount, f or Husqvarna stand 6 W ater connector 7 LEDs f or indicating power output 8 Switch 9 Smar tstar t TM 10 Inspection cov er 11 Leakage hole 12 Inspection hatch 13 Junction coupling (accessory) ...

  • Husqvarna DM 340 - page 6

    6 – English SAFETY INSTR UCTIONS Steps before using a ne w drilling machine • Do not use the drilling machine without first reading and understanding the contents of this Operator’ s Manual. • DM 340 is an electric stand dr ill, intended f or drilling holes in concrete, bricks and v ar ious stone materials. • The machine is intended f or ...

  • Husqvarna DM 340 - page 7

    English – 7 SAFETY INSTR UCTIONS General safety precautions W ork area safety • K eep wor k area clean and well lit. Cluttered or dark areas invite accidents . • Do not operate pow er tools in explosiv e atmospheres, such as in the presence of flammable liquids , gases or dust. P ower tools create sparks which may ignite the dust or fumes. ? ...

  • Husqvarna DM 340 - page 8

    8 – English SAFETY INSTR UCTIONS Use and care • Ne ver use a machine that is f aulty . Carr y out the checks, maintenance and ser vice instructions descr ibed in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists . See instructions under the heading Maintenance. • Inspection and/or mai ...

  • Husqvarna DM 340 - page 9

    English – 9 SAFETY INSTR UCTIONS Machine ′′ ′ ′ s saf ety equipment This section describes the machine ′ s safety equipment, its pur pose, and ho w checks and maintenance should be carried out to ensure that it operates correctly . See the ”What is what?” section to locate where this equipment is positioned on your machine . Switch ...

  • Husqvarna DM 340 - page 10

    10 – English ST ARTING AND ST OPPING Bef ore star ting Make sure that: • P ower s witch, cord and electrical outlet are intact. If not, they m ust be replaced by an authorised repair man. • Cooling air vents are not b locked. • The machine and its equipment are correctly installed. • The stand is properly fixed and that the drill is prop ...

  • Husqvarna DM 340 - page 11

    English – 11 MAINTENANCE General The lif etime of your machine can be e xtended considerably if it is used, cared f or and maintained in the proper manner . Changing the drill bit 1 Pull out the plug. 2 Get: - The new drill bit. - Open-ended spanners, siz e 24 mm and 32 mm. - Water-resistant grease . 3 Remov e the old dr ill bit using the open-en ...

  • Husqvarna DM 340 - page 12

    12 – English MAINTENANCE 6 If necessar y contact your dealer to clean the gearbo x. 7 P our the new oil into the gearbo x, about 0.5 litres. 8 Check that the sealing lip on the r adial seal is intact. 9 Reassemble the machine and scre w in the four screws . Be careful when assembling so as not to damage the radial seal. Replacing the carbon brush ...

  • Husqvarna DM 340 - page 13

    English – 13 TECHNICAL D A T A DM 340 Electric motor Single-phase Rated voltage , V 230 Rated output, W 3600 Rated current, A 16 W eight, kg 14 Max. diameter drill bit, mm/inch 400/16 W ater cooling Spindle thread G 1 1/4” W ater connector G 1/4” W ater pressure - max, bar 8 Noise emissions Sound power le vel, measured, EN 12348:2000, dB(A) 9 ...

  • Husqvarna DM 340 - page 14

    14 – English TECHNICAL D A T A EC-declaration of conf ormity (Applies to Eur ope only) Husqvarna AB , SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the Husqvarna DM 340 , from 2009´s serial numbers and onwards (the y ear is clearly stated in plain text on the rating plate with subsequent serial number), ...

  • Husqvarna DM 340 - page 15

    English – 15 WIRING DIA GRAM ...

  • Husqvarna DM 340 - page 16

    ´®z+TIi¶0G¨ 2009-04-15 ´®z+TIi¶0G¨ 1152417-30 ...

Manufacturer Husqvarna Category Drill

Documents that we receive from a manufacturer of a Husqvarna DM 340 can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- DM 340 manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna DM 340
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna DM 340.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna DM 340, service manual, brief instructions and user manuals Husqvarna DM 340. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna DM 340.

Similar manuals

A complete manual for the device Husqvarna DM 340, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna DM 340 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna DM 340.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna DM 340 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna DM 340, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna DM 340, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna DM 340 - which should help us in our first steps of using Husqvarna DM 340
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna DM 340
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna DM 340 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna DM 340?

Use the form below

If you did not solve your problem by using a manual Husqvarna DM 340, ask a question using the form below. If a user had a similar problem with Husqvarna DM 340 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)