Manual Peavey PCX-V12

24 pages 0.79 mb
Download

Go to site of 24

Summary
  • Peavey PCX-V12 - page 1

    P C X - V 1 2 P C X - V 1 2 T rue diversity VHF wireless receiver T rue diversity VHF wireless receiver OPERATING GUIDE ...

  • Peavey PCX-V12 - page 2

    Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suf ficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the produ ...

  • Peavey PCX-V12 - page 3

    INTRODUCTION Thank you for selecting a Peavey Pro Comm PCX- V12 quartz controlled single channel true diversity wireless microphone system. Before operating and installing this system please read this instruction manual carefully and thoroughly in order to attain the correct operating procedures and to achieve the best results. T rue Diversity Rece ...

  • Peavey PCX-V12 - page 4

    1. Antenna Input Connector A 2. Power Switch and Indicator: When the switch is turned on the red indicator illuminates to denote normal power status. 3. RF Signal Level Indicator: Indicates the RF signal strength received from the microphone. As soon as the signal is emitted from the microphone the LED indicator illuminates. 4. Audio Signal Level I ...

  • Peavey PCX-V12 - page 5

    7. DC 12V Input Jack: Connect the 12V DC plug from the AC/DC adapter . 8. Balanced Audio Output Jack: XLR type connector 9. Unbalanced Audio Output Jack: 1/4" Phone Jack 10. Unbalanced Level Switch: “LOW selection is for “Microphone-Level” output. “HIGH” selection is for “Line-Out” level output. 1 1. Squelch Adjustment: Adjust th ...

  • Peavey PCX-V12 - page 6

    3. Audio Output Connection: a. Unbalanced Level Switch Setting Position: Make sure to match the unbalanced output setting to the device input setting. The incorrect setting could result in low sensitivity level or over load distortion. Ex. (If you are going into the “Line” input on a mixer or amplifier then the switch should be set to the high ...

  • Peavey PCX-V12 - page 7

    3. TWO 19/2-INCH UNITS RECEIVER INST ALLA TION A. Setup for single half-rack receiver 1. Push the rack mount brackets (RM-1 1) upwards until it is firmly attached to the receiver . (Figure 5) Figure 5 B. Setup for dual half-rack receivers 1. Remove the screws at the top and bottom of the receiver where they will be joined together . Remove one stee ...

  • Peavey PCX-V12 - page 8

    brackets (RM-12) on the outer sides of both receivers as shown in Figure 6. Figure 6 4. After completion, it can be rackmounted into an EIA standard rack case. Shown in Figure 7. 5. Make sure that the system performs correctly by placing the system away from noise sources. Place the receiver at least one meter above the ground and one meter away fr ...

  • Peavey PCX-V12 - page 9

    4. OPERA TION INSTRUCTIONS 1. T urn the volume controls of the receiver and device in use to a minimum setting before turning on the microphone transmitter . After the receivers power switch is set to the on position, the power switch’s red indicator illuminates to denote normal power status. 2. If the SIGNAL LED indicators of the receiver are il ...

  • Peavey PCX-V12 - page 10

    microphone the AUDIO LED indicators will illuminate according to the strength of sound level. If the LEDs do not illuminate or sound is not present at the output, the system is not functioning properly and must be checked. 4. Receiver and Amplifier V olume Adjustment: a. Single-channel Unbalanced Audio Output: Switch the level switch on the rear pa ...

  • Peavey PCX-V12 - page 11

    IN” input jack of the amplifier or mixer . Adjust the volume controls of the amplifier or mixer to the same desired level, then properly fine adjust the receiver volume control to match the same sensitivity as the wired microphone. d. If the receiver output level is adjusted to a level that is near the maximum input level of the desired device, i ...

  • Peavey PCX-V12 - page 12

    5. Caution 1. Since the installation of the antenna influences the operating efficiency of the receiver , the most important rule is to minimize the distance as much as possible between the receiving antenna and the microphone for the best reception and performance. 2. The output voltage of the external DC power supply should not be below 12V , oth ...

  • Peavey PCX-V12 - page 13

    HANDHELD WIRELESS MICROPHONE The Peavey Pro Comm PCX-V12 handheld wireless microphone is a modular design. It also incorporates “Superior frequency tracking and muting techniques” dual- squelch to eliminate noise interference. 1. Unit Features and Functions 1. Grille: Protects cartridge and prevents breathing and wind POP noises. 2. Housing: Up ...

  • Peavey PCX-V12 - page 14

    2. BA TTER Y INSERTION 1. Unscrew the battery cap in a counter- clockwise direction. 2. Insert a 9V battery into the battery compartment according to the correct polarity as shown in Figure12. The moment the battery touches the terminals of the compartment, the indicator will flash briefly . This means the polarity is correct. However , if no flash ...

  • Peavey PCX-V12 - page 15

    4. When the microphone is not in use make sure to turn it off to extend the battery life. Remove the battery from the battery compartment if the microphone will not be in use for a long period of time. If a rechargeable battery is used take it out for a recharge as necessary . BEL T P ACK TRANSMITTER 1. Unit Features and Functions 1. 4-pin Jack Inp ...

  • Peavey PCX-V12 - page 16

    4. Gain Control: Adjusts the input gain to an appropriate level. 5. T ransmitter Housing: Contains the PCB and battery . 6. Battery Status Indicator: Indicates the power on/off and battery status. a. When the power switch is turned on the LED indicator flashes briefly , indicating normal battery status . b. If the LED illumination is sustained at e ...

  • Peavey PCX-V12 - page 17

    1. Push down on the battery cover to open the battery compartment. 2. Insert a 9V battery into the battery compartment according to the correct polarity as shown in Figure 14. Then push up on the battery cover to close the battery compartment. 3. The LED indicator will flash briefly when power is turned on to indicate normal battery status. If no f ...

  • Peavey PCX-V12 - page 18

    3. AF 4-PIN INPUT CONNECTION METHODS 1. 2-Wire Electret condenser microphone Capsule 2. 3-Wire Electret condenser microphone Capsule 3. Dynamic Microphone 4. Electric Guitar 5. Line-in (Impedance 8 K Ω Attenuated 10 dB) 18 ...

  • Peavey PCX-V12 - page 19

    SPECIFICA TIONS 1. Overall: VHF PCX-V12 1. Carrier Frequency Range: VHF Band 160~250 MHz 2. Oscillation Mode: Quartz-controlled 3. Channel: 1-channel fixed 4. Stability: + 0.005 % with temperature compensation 5. Max. Deviation: + 15 KHz with level limiting 6. Dynamic Range: > 1 10 dB 7. S/N Ratio: > 102 dB 8. T .H.D.: < 0.5 % 9. Squelch: ...

  • Peavey PCX-V12 - page 20

    20 TROUBLESHOOTING GUIDE Symptom Distance Possible Possible Cause Solution No AF signal Any low transmitter replace battery and no RF signal battery voltage No AF signal long out of range move transmitter and no RF signal closer to receiver or obstecles No AF signal any microphone or check input source but normal RF signal other input source Distor ...

  • Peavey PCX-V12 - page 21

    NOTES: 21 ...

  • Peavey PCX-V12 - page 22

    PEA VEY ELECTRONICS CORPORA TION LIMITED W ARRANTY Effective Date: July 1, 1998 What This Warranty Covers Y our Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada. What This Warranty Does Not Cover The Warranty does not cover: (1) damage caused by accident, misuse, abuse, im ...

  • Peavey PCX-V12 - page 23

    IMPOR T ANT SAFETY INSTRUCTIONS W ARNING: When using electric products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . For example, near or in a bathtub, swimming pool, sink, wet bas ...

  • Peavey PCX-V12 - page 24

    Features and specifications subject to change without notice. Peavey Electronics Corporations • 71 1 A Street • Meridian MS • 39301 • (601) 483-5365 • Fax 486-1278 ©2000 ...

Manufacturer Peavey Category Home Security System

Documents that we receive from a manufacturer of a Peavey PCX-V12 can be divided into several groups. They are, among others:
- Peavey technical drawings
- PCX-V12 manuals
- Peavey product data sheets
- information booklets
- or energy labels Peavey PCX-V12
All of them are important, but the most important information from the point of view of use of the device are in the user manual Peavey PCX-V12.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Peavey PCX-V12, service manual, brief instructions and user manuals Peavey PCX-V12. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Peavey PCX-V12.

Similar manuals

A complete manual for the device Peavey PCX-V12, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Peavey PCX-V12 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Peavey PCX-V12.

A complete Peavey manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Peavey PCX-V12 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Peavey PCX-V12, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Peavey PCX-V12, that we can find in the current document
3. Tips how to use the basic functions of the device Peavey PCX-V12 - which should help us in our first steps of using Peavey PCX-V12
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Peavey PCX-V12
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Peavey PCX-V12 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Peavey PCX-V12?

Use the form below

If you did not solve your problem by using a manual Peavey PCX-V12, ask a question using the form below. If a user had a similar problem with Peavey PCX-V12 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)