Manual Chamberlain 2500BC

72 pages 4.63 mb
Download

Go to site of 72

Summary
  • Chamberlain 2500BC - page 1

    Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless The Protector System ® is connected and properly aligned. ■ Periodic checks of the opener are required to ensure safe operation. ■ The model number label is ...

  • Chamberlain 2500BC - page 2

    2 Introduction 2-5 Safety symbol review and signal word review ............2 Preparing your garage door ........................................3 T ools ............................................................................3 Planning .....................................................................4 Carton inventory ...................... ...

  • Chamberlain 2500BC - page 3

    3 Preparing your garage door Before you begin: • Disable locks. • Remove any ropes connected to garage door . • Complete the following test to make sure your garage door is balanced and is not sticking or binding: 1. Lift the door about halfway as shown. Release the door . If balanced, it should stay in place, supported entirely by its spring ...

  • Chamberlain 2500BC - page 4

    Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 20 for details. Header Wall Safety Reversing Sensor Support bracket & fastening hardware is required. See page 13. FINISHED CEILING Extension Spring OR Torsion Spring Motor un ...

  • Chamberlain 2500BC - page 5

    5 Straight Door Arm Section Curved Door Arm Section Header Bracket U P C E IL IN G M O U N T O N L Y 2-Conductor Bell Wire White & White/Red Safety Labels and Literature Remote Control Transmitter Visor Clip Door Bracket SECURITY ✚ 3-Button Remote Control (2) Safety Reversing Sensors (1 Sending Eye and 1 Receiving Eye) with 2-Conductor White ...

  • Chamberlain 2500BC - page 6

    ASSEMBL Y STEP 1 Attach the Rail to the Motor Unit T o avoid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the two washered bolts mounted in top of motor unit. • Align rail and styrofoam over sprocket. Cut tape from rail, belt and styrofoam. • REMOVE STYROFOAM. • Insert both washered bolts ...

  • Chamberlain 2500BC - page 7

    ASSEMBL Y STEP 3 Attach the Belt Cap Retainer • Position the belt cap retainer over the opener sprocket so the two holes in cap align with the two holes in mounting plate. Attach with #8x3/8" hex screws provided. Y ou have now finished assembling your garage door opener . Please read the following warnings before proceeding to the installati ...

  • Chamberlain 2500BC - page 8

    8 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . SECTIONAL DOOR AND ONE-PIECE DOOR WITH TRACK 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header wall above the do ...

  • Chamberlain 2500BC - page 9

    9 ONE-PIECE DOOR WITHOUT TRACK 1. Close the door and mark the inside vertical centerline of your garage door . Extend the line onto the header wall above door , as shown. If headroom clearance is minimal, you can install the header bracket on the ceiling. See page 10. If you need to install the header bracket on a 2x4 (on wall or ceiling), use lag ...

  • Chamberlain 2500BC - page 10

    10 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the garage door , or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry , use concrete anchors (not provided). W ALL HE ...

  • Chamberlain 2500BC - page 11

    Header Bracket Belt Pulley Bracket Opener Carton or Temporary Support Header Wall Garage Door Clevis Pin 5/16"x2-3/4" Ring Fastener Torsion Spring Rail Clevis Pin 5/16"x2-3/4" Ring Fastener Header Bracket Belt Pulley Bracket Foam Packaging Rail 11 HARDW ARE SHOWN ACTUAL SIZE INST ALLA TION STEP 3 Attach the Rail to the Header Br ...

  • Chamberlain 2500BC - page 12

    12 ONE-PIECE DOOR WITHOUT TRACK A 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder . Y ou will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 on its side on the top section of the door beneath the rail. ...

  • Chamberlain 2500BC - page 13

    13 INST ALLA TION STEP 5 Hang the Opener Three representative installations are shown. Y ours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener . This bracket and fastening hardware are not provide ...

  • Chamberlain 2500BC - page 14

    T o prevent possible SERIOUS INJURY or DEA TH from electrocution: • Be sure power is not connected BEFORE installing door control. • Connect ONL Y to 24 VOL T low voltage wires. T o prevent possible SERIOUS INJURY or DEA TH from a closing garage door: • Install door control within sight of garage door , out of reach of children at a minimum h ...

  • Chamberlain 2500BC - page 15

    15 INST ALLA TION STEP 7 Install the Lights and Lens Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in each socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes whe ...

  • Chamberlain 2500BC - page 16

    INST ALLA TION STEP 9 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, conta ...

  • Chamberlain 2500BC - page 17

    17 Invisible Light Beam Protection Area Sensor Beam 6" (15 cm) max. above floor Sensor Beam 6" (15 cm) max. above floor Facing the door from inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direct ...

  • Chamberlain 2500BC - page 18

    18 DOOR TRACK MOUNT (RIGHT SIDE) Indicator Light Lens Lip Sensor Bracket Door Track FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) Indicator Light Sensor Bracket Lens Extension Bracket (See Accessories) Inside G arage W all (Provided with Extension Bracket) (Provided with Extension Bracket) Figure 1 Figure 2 Figure 3 Figure 4 WALL MOUNT (RIGHT SI ...

  • Chamberlain 2500BC - page 19

    19 Invisible Light Beam Protection Area Sensor Sensor Bell Wire Bell Wire Finished Ceiling Quick-Connect Terminals Strip wire 7/16" 7/16" Sensor Connections Connect Wire to Quick-Connect Terminals White/black wire White wire Red Grey White Carriage Bolt 1/4"-20x1/2" Lens Wing Nut Figure 4 Figure 5 MOUNTING AND WIRING THE SAFETY ...

  • Chamberlain 2500BC - page 20

    20 INST ALLA TION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel. Figure 1 shows one piece o ...

  • Chamberlain 2500BC - page 21

    21 ONE-PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also. • Center the door bracket on the top of the door , in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes. • Metal Doors: Drill 3/16" pilot holes ...

  • Chamberlain 2500BC - page 22

    INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back (away from the door ...

  • Chamberlain 2500BC - page 23

    ALL ONE-PIECE DOORS 1. Assemble the Door Arm: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • Make sure the garage door is fully closed. Connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin. • Secure with a ring fastener ...

  • Chamberlain 2500BC - page 24

    4. Open and close the door with the remote control or door control 2 or 3 times. • If the door does not stop in the desired UP (open) position or reverses before the door stops at the DOWN (close) position, proceed to Adjustment Step 2 Setting the Force. • If the door stops in both the desired UP (open) and DOWN (close) positions, proceed to Ad ...

  • Chamberlain 2500BC - page 25

    ADJUSTMENT STEP 2 Setting the Force The force setting button is located on the back panel of the motor unit. The force setting measures the amount of force required to open and close the door . 1. Locate the orange button on the back panel of unit (Figure 1) . 2. Push the orange button twice to enter unit into Force Adjustment Mode (Figure 2). The ...

  • Chamberlain 2500BC - page 26

    ADJUSTMENT STEP 3 T est the Safety Reversal System TEST • With the door fully open, place a 1-1/2" board (or a 2x4 laid flat) on the floor , centered under the garage door . • Operate the door in the down direction. The door must reverse on striking the obstruction. Upon successful safety reversal test proceed to Adjustment Step 4 . ADJUST ...

  • Chamberlain 2500BC - page 27

    OPERA TION 27 Using Y our Garage Door Opener Y our Security ✚ ® opener and hand-held remote control have been factory programmed to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with several Security ✚ ® remote controls utilizing up to 12 functions, and one Security ✚ ? ...

  • Chamberlain 2500BC - page 28

    28 Using the W all-Mounted Door Control THE MUL TI-FUNCTION DOOR CONTROL Press the push bar to open or close the door . Press again to reverse the door during the closing cycle or to stop the door while it's opening. Light feature Press the Light button to turn the opener light on or off. It will not control the opener lights when the door is ...

  • Chamberlain 2500BC - page 29

    29 CARE OF YOUR OPENER MAINTENANCE SCHEDULE Once a Month • Manually operate door . If it is unbalanced or binding, call a trained door systems technician. • Check to be sure door opens & closes fully . Adjust limits and/or force if necessary . (See pages 24 and 25) • Repeat the safety reverse test. Make any necessary adjustments. (See Adj ...

  • Chamberlain 2500BC - page 30

    30 Having a Problem? (Continued) 6. The garage door opens and closes by itself: • Be sure that all remote control push buttons are off. • Remove the bell wire from the door control terminals and operate from the remote only . If this solves the problem, the door control is faulty (replace), or there is an intermittent short on the wire between ...

  • Chamberlain 2500BC - page 31

    *3-Button Remotes If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or mini-remote can be programmed to operate other Security ✚ ® garage door openers. T o Erase All Codes From Motor Unit Memory T o deactivate any unwanted remote, first erase ...

  • Chamberlain 2500BC - page 32

    1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Multi-Function Door Control. 3. Continue holding the ENTER and LIGHT buttons while you press the push bar on the Multi-Function Door Control (all three buttons ...

  • Chamberlain 2500BC - page 33

    7 10 11 6 5 N O TIC E U P C E I L I N G M O U N T O N L Y 8 1 4 2 3 9 12 LO CK L IG H T 2 1 5 6 3 7 8 4 Rail Assembly Parts Installation Parts 33 KEY P ART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41A5424 Belt pulley bracket 3 41B3869-1 Complete trolley assembly 4 109B33 T rolley clip 5 183B99 One-piece T -rail 6 41A5434-1 1 Full belt assembl ...

  • Chamberlain 2500BC - page 34

    Motor Unit Assembly Parts 34 2 3 4 5 6 7 8 9 10 11 12 1 KEY P ART NO . NO . DESCRIPTION 1 41A4371-1 Belt cap 2 41B4245-1 Line cord 3 41B4375-3 T er minal b lock w/scre ws 4 41C5317 Wire harness (logic) 41C5839 High voltage wire harness 41C5806 DC motor wire harness 41C5418 Light sock et wire harness 5 41D475-1 Motor 80kg/100kg KEY P ART NO . NO . D ...

  • Chamberlain 2500BC - page 35

    35 LOCK LIGHT C LO SE D O P E N ACCESSORIES 974LMC 970LMC 995LMC 2778BD 41A5281 1702LMC Outside Quick Release: Required for a garage with NO access door . 8 Foot Complete Rail: T o allow an 8 foot door to open fully . Remote Light Control: Enables homeowner to turn on a lamp, television or other appliance from their car with their garage door opene ...

  • Chamberlain 2500BC - page 36

    © 2003, The Chamberlain Group, Inc. 1 14A2797 B All Rights Reserved Printed in Mexico LIFTMASTER SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SERVICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE SEVEN DA YS A WEEK. SIMPL Y DIAL OUR T OLL FREE NUMBER: 1-800-654-4736 HOURS: (Central Std. Time) 6:00 A.M. TO 7:00 ...

  • Chamberlain 2500BC - page 37

    Manuel d'instructions ■ Lire attentivement ce manuel ainsi que les consignes de sécurité! ■ Après la pose, accrocher ce manuel près de la porte de garage pour s'y reporter ultérieurement. ■ La porte NE SE FERMERA P AS si le Système Protector ® n'est pas branché et réglé correctement. ■ Pour un bon fonctionnement en ...

  • Chamberlain 2500BC - page 38

    2 Introduction 2-5 Revue des symboles de sécurité et des mots de signalement . . . . . . . . . . . . . . . . . . . . . . . .2 Préparation de votre porte de garage . . . . . . . . . . . . . . . .3 Outils nécessaires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Planification . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Chamberlain 2500BC - page 39

    3 Pince universelle Pince coupante Marteau Scie à métaux Tournevis Clé à molette Clé à douille et douilles de 1/2 po et 7/16 de po Perceuse Ruban à mesurer 2 1 Escabeau Crayon Niveau de menuisier (Facultatif) Forets de 3/16 de po, de 5/16 de po et 5/32 de po Pour prévenir les dommages à la porte de garage et à l’ouvre-porte : • TOUJOU ...

  • Chamberlain 2500BC - page 40

    Rail Axe de la porte Commande de porte à montage mural Moteur Détecteur inverseur de sécurité Il faudra poser des renforts horizontaux et verticaux dans le cas d'une porte de garage légère (en fibre de verre, en acier, en aluminium, en panneaux de verre, etc.). Se reporter à la page 20 pour plus de détails. PLAFOND FINI Une cornière e ...

  • Chamberlain 2500BC - page 41

    5 U P C E IL IN G M O U N T O N L Y SECURITY ✚ L O C K LIGHT Agrafe de pare-soleil d'télécommande Rail rigide Fil de sonnerie blanc et blanc/rouge à 2 conducteurs Panneau commande de porte à trois boutons Télécommande à trois boutons Support du détecteur de sécurité (2) Support de poulie de courroie Chariot (2) Capteurs d'inve ...

  • Chamberlain 2500BC - page 42

    MONT AGE - 1 re OPÉRA TION Fixation du rail au moteur Pour éviter les difficultés pendant la pose, ne faire fonctionner l'ouvre-porte de garage que lorsque cela est expressément indiqué. • Enlever les deux boulons à rondelles montés sur le dessus du moteur . • Aligner le rail et la mousse de polystyrène au-dessus du pignon. Couper ...

  • Chamberlain 2500BC - page 43

    MONT AGE - 3 e OPÉRA TION Fixation du capuchon de retenue de la courroie • Positionner le capuchon de retenue de la courroie au-dessus du pignon du moteur de façon que les trois trous du capuchon soient alignés avec les deux trous de la plaque de butée. Le fixer avec les vis à tête hexagonale n o 8 x 3/8 fournies. Le montage de l'ouvre ...

  • Chamberlain 2500BC - page 44

    8 POSE – 1 re OPÉRA TION Déterminer l’emplacement du suppor t de linteau Les méthodes de pose varient en fonction de la porte du garage. Suivre les instructions qui correspondent à la porte du garage sur laquelle on pose l’ouvre-porte. PORTE ARTICULÉE ET PORTE RIGIDE MUNIES DE GUIDES 1. Fermer la porte et marquer l’axe vertical intéri ...

  • Chamberlain 2500BC - page 45

    Linteau Axe vertical de la porte du garage 2 x 4 Plafond non fini 2 x 4 MONTAGE DU SUPPORT DE LINTEAU AU PLAFOND EN OPTION Solives Axe vertical de la porte du garage PORTE RIGIDE SANS GUIDES 1. La porte étant fermée, repérer et tracer l’axe vertical intérieur de la porte du garage, et prolonger cette ligne sur le linteau, au-dessus de la port ...

  • Chamberlain 2500BC - page 46

    UP CEILING MOUNT ONLY U P — Plafond fini — Tire-fond de 5/16 po- 9 x 1-5/8 po Linteau Support de linteau 6 po maximum Ressort de la porte Porte de garage Trous de fixation au plafond Le trou du clou n'est prévu que pour le positionnement seulement. Des tire-fond doivent être utilisés pour fixer le support de linteau. Axe vertical de la ...

  • Chamberlain 2500BC - page 47

    11 Support de linteau Support de poulie de courroie Linteau Support temporaire Axe de chape de 5/16 de po x 2-3/4 po Anneau d'arrêt Support de linteau Support de poulie de courroie Rail Porte de garage Rail Mousse d'emballage Ressort à torsion Axe de chape de 5/16 po x 2-3/4 po Anneau d'arrêt GRANDEUR RÉELLE DES FIXA TIONS POSE - ...

  • Chamberlain 2500BC - page 48

    12 PORTE RIGIDE SANS GUIDES Poser un 2x4 sur son côté très bien pour obtenir l'espace qu'il faut entre la porte et le rail. • Enlever l’emballage en mousse. • Lever l'ouvre-porte et le faire reposer sur un escabeau. Si l'escabeau n'est pas assez haut, demander de l'aide. • Ouvrir complètement la porte et me ...

  • Chamberlain 2500BC - page 49

    — PLAFOND FINI — Support caché Région préférée de positionnement des supports Utilisation d'une installation existante Suppor ts e xistants Suppor t (F our ni) Région préférée de positionnement des supports Boulon de 5/16 po-18 x 7/8 po Rondelle de blocage 5/16 po, Écrou de 5/16 po-18 (Non fournie) Boulon de 5/16 po-18 x 7/8 po R ...

  • Chamberlain 2500BC - page 50

    7/16 po Rouge Gris Blanc Pour relâcher le fil, enfoncer la languette à l’aide de l’extrémité du tournevis. Dénuder le fil sur 7/16 po Connexions de commande de porte 14 Pour prévenir d’éventuelles BLESSURES GRA VES ou LA MORT par suite d’électrocution : • S’assurer que le courant est coupé A VANT de poser la commande de porte. ...

  • Chamberlain 2500BC - page 51

    15 Plot de cache-lampe supérieur Fente de chássis supérieure Fentes de chásis inférieures Plot de cache-lampe supérieur Plot de cache-lampe intérieur Cache-lampe Fente de chássis supérieure Ampoule standard de 100 W (max.) Pour prévenir d’éventuelles BLESSURES GRA VES ou LA MORT par suite de la chute d’une porte de garage : • Si po ...

  • Chamberlain 2500BC - page 52

    Pour éviter les difficultés pendant la pose, ne pas faire fonctionner l'ouvre-porte pour le moment. Afin de minimiser les risques de chocs électriques, le cordon d'alimentation de l'ouvre-porte de garage comporte une fiche à trois broches, dont une de mise à la terre. Cette fiche ne peut être branchée que dans une prise de cou ...

  • Chamberlain 2500BC - page 53

    17 Zone de protection du faisceau lumineux invisible Faisceau du détecteur 6 po max au-dessus du sol Faisceau du détecteur 6 po max au-dessus du sol Faisant face à la porte depuis l'intérieur du garage POSE - 10 e OPÉRA TION Pose du Système Protector ® Les détecteurs inverseurs de sécurité doivent être bien branchés et bien aligné ...

  • Chamberlain 2500BC - page 54

    18 POSE DES SUPPORTS S’assurer que l’ouvre-porte est hors tension. Poser et aligner les supports de manière à ce que les détecteurs se fassent face l’un l’autre de part et d’autre de la porte du garage, le faisceau n’étant pas à une hauteur de plus de 6 po au-dessus du sol. Ils peuvent être posés de trois façons, comme suit. Pos ...

  • Chamberlain 2500BC - page 55

    7/16 po Blanc/noir fil Raccorder les fils sur bornes à raccordement rapide Rouge Gris Branchements des détecteurs inverseurs Blanc fil Aire de protection du faisceau du luminère invisible Détecteur inverseur Détecteur inverseur Fil de sonnerie Plafond fini Bornes à raccordement rapide Dénuder le fil sur 7/16 po Blanc Fil de sonnerie Figure 5 ...

  • Chamberlain 2500BC - page 56

    20 Pour prévenir les dommages à la porte de garage, renforcer l’intérieur de la porte par une ferrure angulaire, tant verticalement qu’horizontalement. WARN ING CAUTION WARN ING WARNING ATTENTION AVERTISSEMENT AVERTISSEMENT AVERTISSEMENT POSE - 11 e OPÉRA TION Fixation du support de por te Suivre les instructions qui correspondent au type d ...

  • Chamberlain 2500BC - page 57

    21 Linteau Axe vertical de la porte du garage Plafond fini Placement facultatif du support de la porte Support de linteau Support de la porte Support 2 x 4 Pour une porte sans cadre exposé, ou pour l'installation facultative, utiliser des tire-fonds de 5/16 po x 1-1/2 po (Non Fournis) pour fixer le support de la porte. PORTE MÉTALLIQUE Dessu ...

  • Chamberlain 2500BC - page 58

    22 POSE - 12 e OPÉRA TION Fixation de la biellette au chariot Suivre uniquement les instructions se reportant à votre type de porte, comme illustré ci-dessous et à la page suivante. PORTE ARTICULÉE SEULEMENT • S'assurer que la porte du garage est complètement fermée. T irer la poignée de déclenchement d’urgence pour détacher le c ...

  • Chamberlain 2500BC - page 59

    23 POUR TOUTES LES PORTES RIGIDES 1. Assemblage des biellettes: • Assembler les biellettes droite et courbée à leur plus grande longueur (2 ou 3 trous se chevauchant). • La porte étant fermée, raccorder la biellette droite au support de la porte à l'aide d'un axe de chape de 5/16 po x 1-1/4 po. • Faire tenir l'axe de chape ...

  • Chamberlain 2500BC - page 60

    24 Sans un système d’inversion de sécurité bien installé, des personnes (plus particulièrement les petits enfants) pourraient être GRIÈVEMENT BLESSÉES ou TUÉES par une porte de garage qui se referme. • Un réglage erroné des courses de la porte de garage gênera un fonctionnement approprié du système d’inversion de sécurité. • ...

  • Chamberlain 2500BC - page 61

    Sans un système d’inversion de sécurité bien installé, des personnes (plus particulièrement les petits enfants) pourraient être GRIÈVEMENT BLESSÉES ou TUÉES par une porte de garage qui se referme. • Une trop grande for ce sur la porte de garage gênera un fonctionnement approprié du système d’inversion de sécurité. • Ne JAMAIS ...

  • Chamberlain 2500BC - page 62

    26 Sans un système d’inversion de sécurité bien installé, des personnes (plus particulièrement les petits enfants) pourraient être GRIÈVEMENT BLESSÉES ou TUÉES par une porte de garage qui se referme. • On DOIT procéder à une vérification mensuelle du système d’inversion de sécurité. • Après avoir réglé une commande (for ce ...

  • Chamberlain 2500BC - page 63

    FONCTIONNEMENT Utilisation de votre ouvr e-porte de garage V otre télécommande à main et ouvre-porte Security ✚ ® ont été réglés en usine à un code compatible qui change avec chaque usage, accédant de manière aléatoire à plus de 100 milliards de nouveaux codes. V otre ouvre-porte fonctionnera avec un nombre allant jusqu’à huit té ...

  • Chamberlain 2500BC - page 64

    28 B) Pour actionner une porte en utilisant les trois boutons de la télécommande à main : On peut programmer la télécommande de manière à ouvrir la porte avec le gros bouton, à la refermer avec le bouton central et à arrêter le mouvement de la porte à l’aide du troisième bouton. REMARQUE : Si la télécommande est déjà programmée, ...

  • Chamberlain 2500BC - page 65

    29 ENTRETIEN DE L ’OUVRE-PORTE DE GARAGE PÉRIODICITÉS D’ENTRETIEN Une fois par mois • Faire fonctionner la porte à la main. Si elle est déséquilibrée ou si elle force, appeler un technicien formé en systèmes de porte. • S’assurer que la porte s’ouvre et se ferme complètement. Au besoin, régler les commandes de course et/ou de ...

  • Chamberlain 2500BC - page 66

    Défauts de fonctionnement (suite) 6. La porte s’ouvre et se ferme toute seule : • S’assurer que tous les boutons-poussoirs de la télécommande sont à la position d’arrêt. • Débrancher le fil de sonnerie des bornes de la commande de porte et faire fonctionner la télécommande seulement. Si ceci résout le problème, la commande de po ...

  • Chamberlain 2500BC - page 67

    31 PROGRAMMA TION L ’ouvre-porte de garage a été programmé en usine de manière à fonctionner avec la télécommande à main fournie. La porte s’ouvrira et se fermera lorsqu’on appuie sur le gros bouton-poussoir . Ci-après se trouvent des instructions pour programmer votre ouvre-porte en vue du fonctionnement avec d’autres télécomman ...

  • Chamberlain 2500BC - page 68

    32 Pour Ajouter , Reprogrammer ou Modifier un NIP d’Entrée Sans Clé REMARQUE: V otre nouvelle entrée sans clé doit être programmée de manière à faire fonctionner votre ouvre-porte de garage. UTILISA TION DU BOUT ON « LEARN » UTILISA TION DE LA COMMANDE DE PORTE MUL TIFONCTION 1. Introduire un numéro d’identification personnelle (NIP) ...

  • Chamberlain 2500BC - page 69

    7 10 11 6 5 N O TIC E U P C E I L I N G M O U N T O N L Y 8 1 4 2 3 9 12 LO CK L IG H T 2 1 5 6 3 7 8 4 33 RÉF . N o DE PIÉCE DÉSIGNA TION 1 4A1008 Maillon de raccord 2 41A5424 Support de poulie de courroie 3 41B3869-1 Chariot complet 4 109B33 Pince de chariot 5 183B99 Rail rigide 6 41A5434-1 1 Courroie complète 7 41B4103 Ensamble de tension 8 ...

  • Chamberlain 2500BC - page 70

    Pièces d’assemblage du moteur 34 2 3 4 5 6 7 8 9 10 11 12 1 RÉF . N° DE PIÈCE DÉSIGNA TION 1 41A4371-1 Capuchon de retenue de la courroie 2 41B4245-1 Cordon électrique 3 41B4375-3 Bornier avec vis 4 41C5317 F aisceau électr ique av ec pr ise (logique) 41C5839 Har nais de fils haute tension 41C5806 DC moteur faisceau électrique av ec prise ...

  • Chamberlain 2500BC - page 71

    LOCK LIGHT C LO S E D O P E N 35 ACCESSOIRES 41A5281 Supports de rallonge : (Facultatif) Pour la pose du capteur de sécurité au mur ou au sol. 1702LMC 976LMC Détachement rapide d'extérieur : Nécessaire pour un garage SANS porte d'accès. Permet au propriétaire d'ouvrir la porte de garage manuellement à partir de l'extéri ...

  • Chamberlain 2500BC - page 72

    © 2003, THE CHAMBERLAIN GROUP 1 14A2797 B All Rights Reserved Printed in Mexico SER VICE LIFTMASTER À VOTRE DISPOSITION NOTRE IMPORT ANT ORGANISA TION DE SERVICE APRÈS-VENTE COUVRE TOUTE LES ÉT A TS-UNIS E LE CANADA. SEPT JOURS P AR SEMAINE, VOUS POUVEZ OBTENIR P AR TÉLÉPHONE DES INFORMA TION SUR L'INST ALLA TION ET LE SERVICE APRÈS-VEN ...

Manufacturer Chamberlain Category Garage Door Opener

Documents that we receive from a manufacturer of a Chamberlain 2500BC can be divided into several groups. They are, among others:
- Chamberlain technical drawings
- 2500BC manuals
- Chamberlain product data sheets
- information booklets
- or energy labels Chamberlain 2500BC
All of them are important, but the most important information from the point of view of use of the device are in the user manual Chamberlain 2500BC.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Chamberlain 2500BC, service manual, brief instructions and user manuals Chamberlain 2500BC. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Chamberlain 2500BC.

Similar manuals

A complete manual for the device Chamberlain 2500BC, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Chamberlain 2500BC by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Chamberlain 2500BC.

A complete Chamberlain manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Chamberlain 2500BC - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Chamberlain 2500BC, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Chamberlain 2500BC, that we can find in the current document
3. Tips how to use the basic functions of the device Chamberlain 2500BC - which should help us in our first steps of using Chamberlain 2500BC
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Chamberlain 2500BC
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Chamberlain 2500BC in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Chamberlain 2500BC?

Use the form below

If you did not solve your problem by using a manual Chamberlain 2500BC, ask a question using the form below. If a user had a similar problem with Chamberlain 2500BC it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)