English dropdown-ico

Manual Craftsman 77589

28 pages 1.22 mb
Download

Go to site of 28

Summary
  • Craftsman 77589 - page 1

    Owner's Manual 10 Horse Power CHIPPER-SHREDDER Model No. 247.775890 I I E CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. Printed in U.S.A. 770-081gA ...

  • Craftsman 77589 - page 2

    Content Page Content Page Warranty information 2 Service & Adjustment 15 Safe Operation Practices 3 Off-Season Storage 18 Assembly 5 Trouble-Shooting 19 Operation 8 Parts List 20 Maintenance 12 One-Year Warranty on Craftsman Chipper-Shredder For one year from the date of purchase, when this Craftsman chipper-shredder is maintained, lubricated, ...

  • Craftsman 77589 - page 3

    This symbol points outimportant safety instructions which, if not followed, could endanger the per- sonal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your chipper shredder. Failure to comply with these instructions may result in per- sonal injury.When you see this symbo ...

  • Craftsman 77589 - page 4

    shut off. Never place any part ofthe body in the impeller area until you are sure the impeller has stopped rotating. • Muffler and engine become hot and can cause a bum. Do not touch. • Do not allow leaves or other debris to build-up on engine's muffler. The debds could ignite and cause a fire. • Do not attempt to shred or chip material ...

  • Craftsman 77589 - page 5

    I Rear 2 Bottles of OII Hopper" Chipper Chute Discharge Chute * The hopper is packed in _e top Insert In your chipper-shredder carton. Figure I :hlp Bag Spark Plug Wire Figure 2 IMPORTANT: This unit is shipped without gasoline or oil in the engine. After assembly, see OPERATION section of this manual for proper fuel and engine oil fill-up. NOT ...

  • Craftsman 77589 - page 6

    I Hex Nut J Step 1 Hinge Discharge Chute Wing Knob Figure 3 • Place second spacer over hex bolt inside the other part of the hinge as shown in the inset, Secure tightly with hex lock nut. • Secure both sides of discharge chute to housing using wing knobs that you earlier removed. This is shown in step 2 in Figure 3. Tighten wing knobs. Atta ...

  • Craftsman 77589 - page 7

    • Raise the hopper till it clicks into position. • Unscrew the shoulder bolt from the stop washer on the inlet guide. See Figure 6. • Align the loose end of the flap control rod with the stop washer on the inlet guide. • Slide the shoulder bolt through the opening in the flap control rod. Secure tightly. See Figure 6. & WARNING: This fl ...

  • Craftsman 77589 - page 8

    Read this owner's manual and safety rules before operating your chipper-shredder. Compare Figure 9 with your chipper-shredder to familiarize yourself with thelocation of various controls and adjustments. Save this manual for future reference. The operation of any chipper-shredder can result in foreign objects being thrown into the eyes, which ...

  • Craftsman 77589 - page 9

    Lowering Hopper Assembly In order to rake leaves into the hopper, you will need to lower the hopper. • To lower the hopper assembly, use one hand to grasp the hand-hold at the top of the hopper assembly and lift slightly. See Figure 5. • Pul! up on the release bar, and lower the hopper assembly to the drop-down position. Release the bar. See Fi ...

  • Craftsman 77589 - page 10

    A WARNING: Do not fill closer than 1/2 inch from the top of the fuel tank to prevent spills and to allow for fuel expansion. If gasoline is accidently spilled, move chipper- shredder away from area of spill. Avoid creating any source of ignition until gasoline vapors have disappeared. ° Check the fuel level periodically to avoid running out of gas ...

  • Craftsman 77589 - page 11

    h, hopper assembly when it is in the raised or lowered position. See Figure 13. Bulky material, such as stalks or heavy branches, up to 3" in diameter should be fed into the chipper chute. See Figure 13. A WARNING: Do not put material larger than is specified into the hopper, and/or into the chipper chute. Personal injury or damage to the mach ...

  • Craftsman 77589 - page 12

    General Recommendations • Always observe safety rules when performing any maintenance, • The warranty on this chipper shredder does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain the chipper- shredder as instructed in this manual, • Some adjustments wil ...

  • Craftsman 77589 - page 13

    the oilmust be to FULL mark on dipstick. Change engine oilevery 50 hours of operation under normal operating conditions. Change oil every 25hours when operating nder heavy load or in high temperatures. To Drain Oil Drain oilwhile engine is warm. Follow instructions . given below. • Remove oil drain plug. Catch oil in a suitable container. • Whe ...

  • Craftsman 77589 - page 14

    head, top of piston and around valves. Use a soft brush to remove the deposits. Reassemble gasket and cylinder head. Turn screws down finger-tight. Torque cylinder head screws in a staggered sequence to 165 in.-Ibs. ,_ WARNING: Temperature of muffler and nearby areas may exceed 150 ° F(65°C). Avoid these areas. Spark Plug • Clean the spark plug ...

  • Craftsman 77589 - page 15

    Removing Flail Screen if the discharge area becomes clogged, remove the flail screen and clean area as follows. • Stop engine, make certain the chipper- shredder has come to a complete stop and disconnect spark plug wire from the spark plug before unclogging the chute. • Remove the two hand knobs on each side of the discharge chute (also called ...

  • Craftsman 77589 - page 16

    Pipe Weld Bolt Allen Screw When reassembling the blade, tighten center bolt to between 550-700 inch-pounds and the two outer bolts to 250-300 inch-pounds, or lacking torque wrench, tighten securely. 1. Insert screw driver through hole "-,,.p 2. Blade should be parallel to ground Sc D:d_e_ Blade I I- Ground Torque Wrench Figure 20 • Remove th ...

  • Craftsman 77589 - page 17

    Check idle speed and re-adjust to 1750 rpm, if necessary. Engine should accelerate smoothly, If it does not, adjust idle mixture valve counter-elcckwise 1/8 turn. _lb ARNING: Air cleaner and its cover must be assembled to the carburetor before starting the engine. Adjusting Engine Speed The engine speed on your chipper-shredder has been set at the ...

  • Craftsman 77589 - page 18

    Prepare your chipper-shredder for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store machine with fuel in the fuel tank inside of building where fumes may reach an open flame or spark, or where ignition sources are present such as hot water and space heaters, furnaces, clothes dryers, stoves, ...

  • Craftsman 77589 - page 19

    Problem Corrective Action Engine fails to start Loss of power; operation erratic Engine overheats Too much vibration Unit does not discharge Possible Cause 1. Fuel tank empty, or stale fuel 2. Spark plug wire disconnected 3. Faulty spark plug 4. Fuel shut-off valve not turned ON. 1. Spark plug wire loose 2. Unit running on Choke 3. Blocked fuel lin ...

  • Craftsman 77589 - page 20

    CRAFTSMAN 10 H.P. CHIPPER SHREDDER MODEL 247,775890 2O ...

  • Craftsman 77589 - page 21

    CRAFTSMAN 10 H.P. CHIPPER SHREDDER MODEL 247.775890 Key No. I 2 3 4 5 6" 7 8 9 10 11 12 13 14 15 16 17 18 19 2O 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 4O 41 42 44 Part No. r70-0819A 11480 681-0118 710-0542 _10-0607 710-3256 712-0429 711-1304 i 712-3027 Description Owner's Manual Stop Washer Inlet Guide Assembly Hex Washe ...

  • Craftsman 77589 - page 22

    CRAFTSMAN 10 H.P. ENGINE MODEL NO. 19G432-1182-E1 FOR CHIPPER SHREDDER MODEL NO. 247.775890 Key No. Part No. 1 495631 2 495657 3 .391086 5 214347 7 _.272163 8 498038 9 _27803 10 94621 11 280819 13 94565 14 15 306 307 306 337 383 552 635 869 871 978 979 982 1019 1058 94622 94239 496797 94930 225055 496018 69838 491986 66538 211661 261961 *271736 494 ...

  • Craftsman 77589 - page 23

    CRAFTSMAN 10 H,P. ENGINE MODEL NO. 19G432-1182-E1 FOR CHIPPER SHREDDER MODEL NO, 247.775890 Key No. Part No. Description 12 15A 16 77 18 19 20 21 22 24 25 26 27 28 29 30 32 33 34 35 40 45 46 146 219 220 230 244 411 524 614 616 741 868 *271701 *27876 *27877 91488 495866 29530 496981 295964 *391086 281658 93585 94690 222698 499907 499908 499909 49991 ...

  • Craftsman 77589 - page 24

    CRAFTSMAN 10 H.P. ENGINE MODEL NO. 19G432*1182-E1 FOR CHIPPER SHREDDER MODEL NO. 247.775890 Kay No. Part No. 50 51 51A 53 93 " 94 95 98A 104 105 106 108 123 125 127 130 131 133 137 138 141 142 147 186 634 950 965 975 987 1091 214170 _D,272707 •_?72708 94778 A281346 498836 &94098 495800 tL231789 A231935 _231856 224666 94913 499029 & 2 ...

  • Craftsman 77589 - page 25

    CRAFTSMAN 10 H.P. ENGINE MODEL NO. 19G432-1182-E1 FOR CHIPPER SHREDDER MODEL NO. 247.775890 Key No. 116 209 211 212 212A 227 232 284 422 523 524A 525 562 592 623 624 847 Part No. Description *270920 Seal-O-Ring 263212 Spring-Governor 263182 Spring-Governor Idle 263051 Link-Throttle 263049 Link-Throttle 499096 Lever.-Govemor 263020 Spring-Link 94984 ...

  • Craftsman 77589 - page 26

    CRAFTSMAN 10 H.P. ENGINE MODEL NO. 19G432-1182-E1 FOR CHIPPER SHREDDER MODEL NO. 247.775890 Key No, 23 24 37 38 73 74 75 215 304 305 363 575 1036 Part No. Description 298260 Flywheel 222698 Key-Flywheel 222475 Guard-Flywheel .94811 Screw-Hex. 224874 Screen-Rotating 94680 Screw-Hex. 225136 Washer-Flywheel 221760 Guide-Air 491596 Housing-Blower 94786 ...

  • Craftsman 77589 - page 27

    ...

  • Craftsman 77589 - page 28

    For the repair or replacement parts you need delivered directly to your home Call 7 am - 7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) For in-homemajor brand repair service Call 24 hours a day, 7 days a week 1-8OO-4-REPAIR (1-800-473-7247) For the location of a Sears Parts and Repair Center in your area Call 24 hours a day, 7 days a week _ 1- ...

Manufacturer Craftsman Category Chipper

Documents that we receive from a manufacturer of a Craftsman 77589 can be divided into several groups. They are, among others:
- Craftsman technical drawings
- 77589 manuals
- Craftsman product data sheets
- information booklets
- or energy labels Craftsman 77589
All of them are important, but the most important information from the point of view of use of the device are in the user manual Craftsman 77589.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Craftsman 77589, service manual, brief instructions and user manuals Craftsman 77589. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Craftsman 77589.

Similar manuals

A complete manual for the device Craftsman 77589, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Craftsman 77589 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Craftsman 77589.

A complete Craftsman manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Craftsman 77589 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Craftsman 77589, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Craftsman 77589, that we can find in the current document
3. Tips how to use the basic functions of the device Craftsman 77589 - which should help us in our first steps of using Craftsman 77589
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Craftsman 77589
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Craftsman 77589 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Craftsman 77589?

Use the form below

If you did not solve your problem by using a manual Craftsman 77589, ask a question using the form below. If a user had a similar problem with Craftsman 77589 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)