Manual Extron electronic SI 3

16 pages 1.38 mb
Download

Go to site of 16

Summary
  • Extron electronic SI 3 - page 1

    User’s Guide Compact Full Range Surface Mount Speakers 68-1261-01 Rev . A 11 07 SI 3 System INTEGRA TOR ™ ...

  • Extron electronic SI 3 - page 2

    SI 3 Speakers • Packaging Packaging Information Figure 1 — SI 3 speaker packaging details P a r t N o . X X X -X X X - 01 Install 206W Ce i li n g Spe aker 3 3 -X X X X - 0 1 R E V . Thick Single W all P acking Bottom F oam Speakers (each plastic wrapped) He x T ool (plastic wrapped) T op F oam Product Label W all Mount Assemblies Speaker Rear ...

  • Extron electronic SI 3 - page 3

    Intr oduction SI 3 Speakers • Introduction 1 About the SI 3 Speakers The Extron System INTEGRA TOR ™ SI 3 full range, compact, surface mount speaker is ideally suited for classrooms, conference r ooms, and boardr ooms. W ith a weather resistant construction, it is also suitable for outdoor environments, and has the following features (see below ...

  • Extron electronic SI 3 - page 4

    SI 3 Speakers • Features 2 Featur es Dimensions : 8.75" H x 5.75" W x 5.61" D (22.2 cm H x 14.6 cm W x 14.24 cm D) a Bass reflex port b Front locking access (allows for speaker position adjustment) c 3" full range driver with paper cone d Grill and enclosure may be painted to match envir onment e W eather resistant constructi ...

  • Extron electronic SI 3 - page 5

    Installation 3 SI 3 Speakers • Installation Installing the SI 3 Speakers The Extron SI 3 speakers can be mounted on a surface, such as a wall or post, or mounted in a bookcase, or on a shelf, and can be used with any Extron pr oduct supporting audio. N If the speakers are to be placed on a horizontal surface such as a desk or shelf, attach the ba ...

  • Extron electronic SI 3 - page 6

    4 SI 3 Speakers • Installation Installation, cont’d W all mounting applications Installing the wall mount assembly N Before starting installation, ensur e that the wall and wall material are capable of supporting the combined weight of the speakers and the wall mount assemblies. 1 . If mounting to drywall, use a stud locator to locate the studs ...

  • Extron electronic SI 3 - page 7

    4. Mark the wall where the wir e will pass through the plate, and cut a small access hole large enough for the wir e to pass through without interfer ence. Where the stud is wider than the plate's access hole, cut the hole in the wall to the left or right and directly alongside the stud (see figure 7). N Before cutting the hole in the wall, m ...

  • Extron electronic SI 3 - page 8

    Installation, cont’d 6 SI 3 Speakers • Installation 6 . Pull sufficient wir e up through the holes in the r ear plate (see figure 8) to allow ease of connection to the speaker after installation. N Do not strip and connect the wire at this time. P ass the wires through the plate access hole. Line of Stud Figure 8 — Passing the wir e through t ...

  • Extron electronic SI 3 - page 9

    Installation, cont’d 6 SI 3 Speakers • Installation 6 . Pull sufficient wir e up through the holes in the r ear plate (see figure 8) to allow ease of connection to the speaker after installation. N Do not strip and connect the wire at this time. P ass the wires through the plate access hole. Line of Stud Figure 8 — Passing the wir e through t ...

  • Extron electronic SI 3 - page 10

    8 SI 3 Speakers • Installation Installation, cont’d Wiring the speakers 1. When both speakers are in place, carefully pull enough speaker wir e to reach to the terminals at the back of the each speaker and strip the ends of the wire appr oximately 5/8" (15 mm). T wist the bare strands so that they ar e held firmly in the connectors. 2 . P ...

  • Extron electronic SI 3 - page 11

    5 . Insert the hex tool into the locking access, and slightly loosen the hex cap screw . Adjust the speaker to the desired angle (see figure 13), and tor que the hex cap screw down clockwise until snug, about 6 to 8 turns. The speaker remains secur ely in the desired position. T ur n cloc kwise to tighten. Figure 13 — Adjusting speaker and locki ...

  • Extron electronic SI 3 - page 12

    10 SI 3 Speakers • T roubleshooting Tips T r oubleshooting Tips T o refit the grill : 1 . Carefully pr ess the grill back into place. 2 . Insert and tighten down the screws. 3 . Replace the logo. Securing the grill (optional) N If the speaker makes the grill vibrate and creates unwanted noise when in use, it can be secured to the speaker enclosu ...

  • Extron electronic SI 3 - page 13

    Observed Problem Possible Cause(s) Remedial Action 1 Speaker easily lifted from mount assembly Locking hex cap screw not tightened enough Following the steps on page 9, tighten the hex cap screw until it is not possible to remove the speaker . 2 No sound heard from speakers Speaker cables not connected or damaged Output device (e.g., amplifier) Re ...

  • Extron electronic SI 3 - page 14

    12 SI 3 Speakers • Specifications Audio/acoustic and electrical Speaker type ................................... Indoor/outdoor surface mount speaker Frequency range ............................ 75 Hz to 18 kHz, -10 dB, half space Power capacity .............................. 16 W continuous pink noise 32 W continuous program Nominal sensitivity ...

  • Extron electronic SI 3 - page 15

    Extron’ s W arranty Extron Electr onics warrants this product against defects in materials and workmanship for a period of five years from the date of pur chase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extr on Electronics will, at its option, r epair or replace said prod ...

  • Extron electronic SI 3 - page 16

    © 2007 Extron Electronics. All rights reserved. Extron Electronics, USA 1230 South Lewis Street Anaheim, CA 92805 800.633.9876 714.491.1500 FAX 714.491.1517 Extron Electronics, Europe Beeldschermweg 6C 3821 AH Amersfoort, The Netherlands +800.3987.6673 +31.33.453.4040 FAX +31.33.453.4050 Extron Electronics, Asia 135 Joo Seng Rd. #04-01 PM Industri ...

Manufacturer Extron electronic Category Portable Speaker

Documents that we receive from a manufacturer of a Extron electronic SI 3 can be divided into several groups. They are, among others:
- Extron electronic technical drawings
- SI 3 manuals
- Extron electronic product data sheets
- information booklets
- or energy labels Extron electronic SI 3
All of them are important, but the most important information from the point of view of use of the device are in the user manual Extron electronic SI 3.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Extron electronic SI 3, service manual, brief instructions and user manuals Extron electronic SI 3. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Extron electronic SI 3.

A complete manual for the device Extron electronic SI 3, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Extron electronic SI 3 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Extron electronic SI 3.

A complete Extron electronic manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Extron electronic SI 3 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Extron electronic SI 3, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Extron electronic SI 3, that we can find in the current document
3. Tips how to use the basic functions of the device Extron electronic SI 3 - which should help us in our first steps of using Extron electronic SI 3
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Extron electronic SI 3
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Extron electronic SI 3 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Extron electronic SI 3?

Use the form below

If you did not solve your problem by using a manual Extron electronic SI 3, ask a question using the form below. If a user had a similar problem with Extron electronic SI 3 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)