English dropdown-ico

Manual Cisco Systems 1600

13 pages 0.09 mb
Download

Go to site of 13

Summary
  • Cisco Systems 1600 - page 1

    Cisco 1600 Series Router Architecture ...

  • Cisco Systems 1600 - page 2

    Table of Contents Cisco 1600 Series Router Architecture ............................................................................................................1 Introduction .............................................................................................................................................1 Hardware Overview .......... ...

  • Cisco Systems 1600 - page 3

    Cisco 1600 Series Router Architecture Introduction Hardware Overview Block Diagram Memory Details Boot Sequence Packet Switching Related Information Introduction This document is an overview of the hardware and software architecture of the Cisco 1600 Series Routers. Hardware Overview Cisco 1600 Series routers are composed of the following router mo ...

  • Cisco Systems 1600 - page 4

    Figure 4: Cisco 1604 and 1604R Rear Panel Figure 5: Cisco 1605R Rear Panel The Cisco 1600 series routers are either run−from−Flash or run−from−RAM models. Router model names with an R are run−from−RAM routers; all other models are run−from−Flash. A more detailed description of these two memory architectures are described in Cisco 16 ...

  • Cisco Systems 1600 - page 5

    Non−Volatile RAM (NVRAM), PCMCIA Flash, and WIC. Input/Output (I/O) Buses allow the M68360 to individually control other devices through the SCCs. These include Universal Asynchronous Receiver/Transmitter (UART), the Ethernet controller, and the WAN port interface. ♦ UART is an SCC integrated on the M68360. It provides the necessary user interf ...

  • Cisco Systems 1600 - page 6

    Module − SIMM (72−pin, 60 ns, with or without parity). If SIMM is non−parity, total DRAM can be up to 18 MB. If SIMM is with parity, total DRAM can be up to 16 MB (on−board 2 MB will be disabled). Note: The Cisco 1605−R Series Router has 8 MB on−board. Therefore, total DRAM can be up to 24 MB on that router. For more information, see Co ...

  • Cisco Systems 1600 - page 7

    Bridging software. X.25 software, Version 3.0.0. Basic Rate ISDN software, Version 1.1. 1 Ethernet/IEEE 802.3 interface(s) 1 Serial(sync/async) network interface(s) 1 ISDN Basic Rate interface(s) System/IO memory with parity disabled 2048K bytes of DRAM onboard 16384K bytes of DRAM on SIMM System running from FLASH 7K bytes of non−volatile config ...

  • Cisco Systems 1600 - page 8

    example : boot system flash slot0:c1600−sy−l.122−1a.bin This forces the RxBoot to look for the file "c1600−sy−l.122−1a.bin" on the Flash device called "slot0:". The boot system directive in the router configuration file overrides the configuration register. If there is no boot system statement, and if the configurati ...

  • Cisco Systems 1600 - page 9

    as set forth in subparagraph (c) of the Commercial Computer Software − Restricted Rights clause at FAR sec. 52.227−19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227−7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134−1706 Cisco Internetwork Operating Sy ...

  • Cisco Systems 1600 - page 10

    Cisco IOS software creates these rings on behalf of the media controllers and then manages them jointly with the controllers. Each interface has a pair of rings: a receive (RX) ring for receiving packets and a transmit (TX) ring for transmitting packets. Receive rings have a constant number of packet buffers allocated to them that equals the size o ...

  • Cisco Systems 1600 - page 11

    Step 1 : The interface media controller detects a packet on the network media and copies it into a buffer pointed to by the first free element in the receive ring. Media controllers use the Direct Memory Access (DMA) method to copy packet data into memory. Step 2 : The media controller changes ownership of the packet buffer back to the processor an ...

  • Cisco Systems 1600 - page 12

    switching. The packet goes in the queue of the appropriate process (for instance, an IP packet is placed in the queue for the IP Input process), and the receive interrupt is dismissed. Step 7: Eventually the packet switching process runs, switching the packet and rewriting the MAC header as needed. Note that the packet still has not moved from the ...

  • Cisco Systems 1600 - page 13

    Maximum Number of Interfaces and Subinterfaces for Cisco IOS Platforms: IDB Limits • Product Catalog • All contents are Copyright © 1992−−2002 Cisco Systems Inc. All rights reserved. Important Notices and Privacy Statement. Updated: Oct 10, 2002 Document ID: 5406 Cisco 1600 Series Router Architecture ...

Manufacturer Cisco Systems Category Router

Documents that we receive from a manufacturer of a Cisco Systems 1600 can be divided into several groups. They are, among others:
- Cisco Systems technical drawings
- 1600 manuals
- Cisco Systems product data sheets
- information booklets
- or energy labels Cisco Systems 1600
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Systems 1600.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Systems 1600, service manual, brief instructions and user manuals Cisco Systems 1600. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Systems 1600.

Similar manuals

A complete manual for the device Cisco Systems 1600, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Systems 1600 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Systems 1600.

A complete Cisco Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Systems 1600 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Systems 1600, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Systems 1600, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Systems 1600 - which should help us in our first steps of using Cisco Systems 1600
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Systems 1600
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Systems 1600 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Systems 1600?

Use the form below

If you did not solve your problem by using a manual Cisco Systems 1600, ask a question using the form below. If a user had a similar problem with Cisco Systems 1600 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)