Manual Hearth and Home Technologies QV32B-A

72 pages 4.1 mb
Download

Go to site of 72

Summary
  • Hearth and Home Technologies QV32B-A - page 1

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 1 • DO NOT store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - DO NOT try to light any appliance. - DO NOT touch any electrical switch. DO NOT use any phone in your building. - Immediately ca ...

  • Hearth and Home Technologies QV32B-A - page 2

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 2 Not for use with solid fuel. ( Ne doit pas entre utilise avec un combustible solide). This appliance must be installed in a ccordance with local codes, if any; if not, follow ANSI Z 223.1 in th e US A or CAN/CG A B149 installation codes. (Installer l’ appa re il selon les codes ou r ...

  • Hearth and Home Technologies QV32B-A - page 3

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 3 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury . • CAUTION! Indicates a hazardous situation which ...

  • Hearth and Home Technologies QV32B-A - page 4

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 4  = Contains updated information. 13 Finishing A. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 52 B. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 14 Appliance Setup A. Remove Fixed Glass Assembly . . . . . . . . . ...

  • Hearth and Home Technologies QV32B-A - page 5

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 5 B. Limited Lifetime W arranty 4021-645C 12-29-10 Page 1 of 2 Hearth & Home T echnologies Inc. LIMITED LIFETIME W ARRANTY Hearth & Home T echnologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric he ...

  • Hearth and Home Technologies QV32B-A - page 6

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 6 4021-645C 12-29-10 Page 2 of 2 W ARRANTY CONDITIONS:  7KLVZDUUDQWRQOFRYHUV++7DSSOLDQFHVWKDWDUHSXUFKDVHGW KURXJKDQ++7 DXWKRUL]HGGHDOHURUGLVWULEXWRU  $ OLVWRI ++7DXWKRUL]HGGHDOHUVLVDYDLODEOHRQWKH++7 ...

  • Hearth and Home Technologies QV32B-A - page 7

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 7 B. T empered Glass Speci fi cations Hearth & Home T echnologies appliances manufactured with tempered glass may be installed in hazardous loca- tions such as bathtub enclosures as de fi ned by the Con- sumer Product Safety Commission (CPSC). The tempered glass has been tested an ...

  • Hearth and Home Technologies QV32B-A - page 8

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 8 H. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the si ...

  • Hearth and Home Technologies QV32B-A - page 9

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 9 Figure 2.1 General Operating Parts B. Y our Fireplace W ARNING! DO NOT operate fi replace before read- ing and understanding operating instructions. Failure to operate fi replace according to operating instructions could cause fi re or injury . DECORA TIVE DOORS (NOT SHOWN) SECTION ...

  • Hearth and Home Technologies QV32B-A - page 10

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 10 D. Clear Space W ARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects. Figure 2.2 Clear Sp ...

  • Hearth and Home Technologies QV32B-A - page 11

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 1 1 I. Lighting Instructions (Standing Pilot) 1. Turn of f all electric power to the appliance if ser- vice is to be performed. 2. Open control access panel. 3. Move switch to “OFF” position. 4. Push in gas control knob slightly and turn clock- wise to OFF”. DO NOT force. 5. Close ...

  • Hearth and Home Technologies QV32B-A - page 12

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 12 J. After Fireplace is Lit Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • T urn the fi replace of f and allow it to completely cool. • Remove fi xed glass assembly . See Section 14.G. • Clean fi xed glass assembly . See ...

  • Hearth and Home Technologies QV32B-A - page 13

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 13 Glass Cleaning Frequency: Seasonally By: Homeowner T ools Needed : Protective gloves, glass cleaner , drop cloth and a stable work surface. CAUTION! Handle fi xed glass assembly with care. Glass is breakable. • Avoid striking, scratching or slamming glass • Avoid abrasive cleane ...

  • Hearth and Home Technologies QV32B-A - page 14

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 14 B. Maintenance T asks-Quali fi ed Service T echnician The following tasks must be performed by a quali fi ed ser- vice technician. Gasket Seal and Glass Assembly Inspection Frequency: Annually By: Quali fi ed Service T echnician T ools needed: Protective gloves, drop cloth and a s ...

  • Hearth and Home Technologies QV32B-A - page 15

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 15 A. T ypical Appliance System NOTICE: Illustrations and photos re fl ect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual Figure 4.1 T ypical System HORIZONT AL TERMINA TION CAP (SE ...

  • Hearth and Home Technologies QV32B-A - page 16

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 16 B. Design and Installation Considerations Quadra-Fire direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. Installation MUST comply ...

  • Hearth and Home Technologies QV32B-A - page 17

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 17 5 5 F raming and Clearances A. Selecting Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1). W ARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service acces ...

  • Hearth and Home Technologies QV32B-A - page 18

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 18 C B D A B. Constructing the Appliance Chase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should be enclosed inside the chase. NOTICE: T reatment of ceiling fi restops and wall shield fi restops and c ...

  • Hearth and Home Technologies QV32B-A - page 19

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 19 D. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances as speci fi ed. Framing or fi nishing material closer than the minimums listed must be constructed entirely of noncom- bustible materials (i.e., steel studs, concrete board, etc). Figure 5. ...

  • Hearth and Home Technologies QV32B-A - page 20

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 20 A. V ent T ermination Minimum Clearances Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.0* Over 6/12 to 7/12 .................................................1.25* Over 7/12 to 8/12 .................................................1.5 ...

  • Hearth and Home Technologies QV32B-A - page 21

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 21 Figure 6.3 Minimum Clearances for T ermination O N P R Q X = AIR SUPPL Y INLET A = 12 inches................. clearances above grade, veranda, porch, deck or balcony B = 12 inches................. clearance to window or door that may be opened, or to permanently closed window C = 18 ...

  • Hearth and Home Technologies QV32B-A - page 22

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 22 A. Approved Pipe This appliance is approved for use with Hearth & Home T echnologies DVP or SLP venting systems. Refer to Sec- tion 16B for vent component information. DO NOT mix pipe, fi ttings or joining methods from differ- ent manufacturers. The pipe is tested to be run insi ...

  • Hearth and Home Technologies QV32B-A - page 23

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 23 E. Use of Flex V ent The fl ex vent must be supported with the spacing between support intervals not exceeding 4 feet, with no more than 1/2 inch sag between supports. A support is required at each change in venting direction, and in any location where it is necessary to maintain th ...

  • Hearth and Home Technologies QV32B-A - page 24

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 24 F . V ent Diagrams Figure 7.4 Note: T here MUST b e a 25% reduc tion in total H w hen using fl ex vent exc ep t wh en using the si mple up and out installation (see Figure 5.3 ). Note: Use SL P Series components only . T op V ent - Horizontal T ermination V enting with 1 elbow (NG) ...

  • Hearth and Home Technologies QV32B-A - page 25

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 25 Figure 7.5 T op V ent - Horizontal T ermination V enting with 2 elbows (NG) T op V ent - Horizontal T ermination V enting with 2 elbows (Propane) Note: T here MUST b e a 25% reduc tion in total H w hen using fl ex vent exc ep t wh en using the si mple up and out installation (see Fi ...

  • Hearth and Home Technologies QV32B-A - page 26

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 26 Figure 7.6 T op V ent - Horizontal T ermination V enting with 3 elbows (NG) T op V ent - Horizontal T ermination V enting with 3 elbows (Propane) Note: T here MUST b e a 25% reduc tion in total H w hen using fl ex vent exc ep t wh en using the si mple up and out installation (see Fi ...

  • Hearth and Home Technologies QV32B-A - page 27

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 27 T op V ent - V ertical T ermination No Elbow V 1 = 60 ft. Max. (18.3 m) Figure 7.8 INNER HEA T SHIELD T op V ent Application Rear V ent Application Note : Be sure to re- install the inner heat shield after exhaust restrictor installation. Figure 7.7 Exhaust restrictors are recommende ...

  • Hearth and Home Technologies QV32B-A - page 28

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 28 Figure 7.9 T op V ent - V ertical T ermination V enting with 2 elbows (NG) T op V ent - V ertical T ermination V enting with 2 elbows (Propane) Note: T here MUST b e a 25% reduc tion in total H w hen using fl ex vent exc ep t wh en using the si mple up and out installation (see Figu ...

  • Hearth and Home Technologies QV32B-A - page 29

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 29 Figure 7.10 T op V ent - V ertical T ermination V enting with 3 elbows (NG) T op V ent - V ertical T ermination V enting with 3 elbows (Propane) Note: T here MUST b e a 25% reduc tion in total H w hen using fl ex vent exc ep t wh en using the si mple up and out installation (see Fig ...

  • Hearth and Home Technologies QV32B-A - page 30

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 30 V 1 H 1 V 2 V 3 H 2 T op V ent - V ertical T ermination - (continued) Four 90º Elbows V 1 Min. H 1 Max. V 2 Min. H 2 Max. V 3 Min. 1-1/2 ft. 457 mm 4 ft. 1.2 m 4 ft. 1.2 m 4 ft. 1.2 m 3-1/2 ft. 1.0 m V 1 + V 2 + V 3 + H 1 + H 2 Maximum= 40 ft. (12.2 m) Figure 7.1 1 Note : Use SLP Se ...

  • Hearth and Home Technologies QV32B-A - page 31

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 31 Figure 7.12 H 1 = 24 in. (71 1 mm) Maximum Rear V ent - Horizontal T ermination No Elbows Rear V ent - Horizontal T ermination V enting with 2 elbows H 1 MAX. V 1 MIN. H 2 MAX. H 1 + H 2 MAX. 1-1/2 ft. 457 mm Back to back elbows 1 ft. 305 mm 2-1/2 ft. 762 mm 3 ft. 914 mm 1 ft. 305 mm ...

  • Hearth and Home Technologies QV32B-A - page 32

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 32 Rear V ent - Horizontal T ermination V enting with 3 elbows H 1 MAX. V 1 MIN. H 1 + H 2 MAX. H 1 + H 2 + H 3 MAX. 1-1/2 ft. 457 mm Back to back elbows 1 ft. 305 mm 2-1/2 ft. 762 mm 3-1/2 ft. 1.1 m 1 ft. 305 mm 2 ft. 610 mm 5-1/2 ft. 1.7 m 5-1/2 ft. 1.7 m 2 ft. 610 mm 4 ft. 1.2 m 9-1/ ...

  • Hearth and Home Technologies QV32B-A - page 33

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 33 INST ALLED HORIZONT ALL Y H 1 H 2 V 2 Figure 7.16 Rear V ent - V ertical T ermination V enting with 2 elbows V 1 MIN. H 1 MAX. H 2 MAX. H 1 + H 2 MAX. Back to back elbows 1-1/2 ft. 457 mm 1 ft. 305 mm 2-1/2 ft. 762 mm 1 ft. 305 mm 3-1/2 ft. 1.1 m 3 ft. 914 mm 6-1/2 ft. 2.0 m 2 ft. 61 ...

  • Hearth and Home Technologies QV32B-A - page 34

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 34 Clearances to Combustibles: Refer to Section 5 for clearances to the appliance, man- tel, mantel legs and wall projection. Refer to Section 8 for pipe clearances to combustibles. T ermination Cap For installation of termination cap see minimum vent heights for various pitched roofs. ...

  • Hearth and Home Technologies QV32B-A - page 35

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 35 EXISTING CHIMNEY HEARTH FLOOR EXISTING CHIMNEY EXHAUST AIR VENT PIPE INLET AIR VENT PIPE T o minimize cold air drafts, seal with non-combustible insulation. TERMINA TION CAP DIRECT VENT FIREPLACE V TERMINA TION CAP EXISTING CHIMNEY EXISTING CHIMNEY EXHAUST AIR VENT PIPE V FLOOR HEART ...

  • Hearth and Home Technologies QV32B-A - page 36

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 36 A. Pipe Clearances to Combustibles W ARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles: • Between ceiling fi restops • Between wall shield fi restops • Around vent system Failure to keep insulation or other material away ...

  • Hearth and Home Technologies QV32B-A - page 37

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 37 C. Install the Ceiling Firestop A ceiling fi restop MUST be used between fl oors and attics. • DVP pipe only - Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/ fl oor (see Figure 8.3). • SLP pipe only - Frame opening 9 in. x 9 in. (2 ...

  • Hearth and Home Technologies QV32B-A - page 38

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 38 D. Install Attic Insulation Shield W ARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home T echnologies Inc. requires the use of an attic shield. The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 ga ...

  • Hearth and Home Technologies QV32B-A - page 39

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 39 CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during installa- tion. Sheet metal edges are sharp. NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time. A. T op V ent 9 9 Appliance Preparation Fig ...

  • Hearth and Home Technologies QV32B-A - page 40

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 40 B. Rear V ent NOTICE: Once appliance is set up for top or rear venting, it CANNOT be changed at a later time. NOTICE: Once the seal cap has been removed it CANNOT be reattached. Figure 9.8 Fold the tabs toward the center of the fi re plug (90°) and remove the insulation gasket. Fig ...

  • Hearth and Home Technologies QV32B-A - page 41

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 41 C. Securing and Leveling the Appliance W ARNING! Risk of Fire! Prevent contact with: • Sagging or loose insulation • Insulation backing or plastic • Framing and other combustible materials Block openings into the chase to prevent entry of blown- in insulation. Make sure insulat ...

  • Hearth and Home Technologies QV32B-A - page 42

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 42 1 0 10 Inst alling V ent Pipe ( DVP and S LP Pi p e ) A. Assemble V ent Sections (DVP Pipe Only) Attach V ent to the Firebox Assembly Note: The end of the pipe sec tions wi t h the lanced tabs wi ll face toward the appliance. Attach the fi rst pipe section to the starting collar: ? ...

  • Hearth and Home Technologies QV32B-A - page 43

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 43 B. Assemble V ent Sections (SLP Pipe Only) T o attach the fi rst vent component to the starting collars of the appliance: • Lock the vent components into place by sliding the pipe section onto the collar . • Align the seam of the pipe and seam of collar to allow engagement. Rota ...

  • Hearth and Home Technologies QV32B-A - page 44

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 44 120º Figure 10.8 Securing V ertical Pipe Sections 120º Figure 10.9 Securing Horizontal Pipe Sections E. Disassemble V ent Sections • Rotate either section (see Figure 10.10) so the seams on both pipe sections are aligned as shown in Figure 10.1 1. • Pull carefully to separate t ...

  • Hearth and Home Technologies QV32B-A - page 45

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 45 F . Install Decorative Ceiling Components (SLP only) A decorative ceiling thimble can be installed on a fl at ceil- ing through which the vent passes. The decorative ceiling thimble is used to cover the fi restop. • Seal the gap between the vent pipe and fi restop using silicone ...

  • Hearth and Home Technologies QV32B-A - page 46

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 46 G. Install Metal Roof Flashing • See minimum vent heights for various pitched roofs (Figure 10.14) to determine the length of pipe to extend through the roof. • Slide the roof fl ashing over the pipe sections extending through the roof as shown in Figure 10.15. Roof Pitch H (Min ...

  • Hearth and Home Technologies QV32B-A - page 47

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 47 SCREWS CAULK STORM COLLAR (1 of 3) Figure 10.18 Figure 10.18 TERMINA TION CAP I. Install V ertical T ermination Cap • Attach the vertical termination cap by sliding the inner collar of the cap into the inner fl ue of the pipe section while placing the outer collar of the cap over ...

  • Hearth and Home Technologies QV32B-A - page 48

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 48 Figure 10.20 V enting through the wall INTERIOR HEA T SHIELD OR EXTENDED HEA T SHIELD W ALL SHIELD FIRESTOP HEA T SHIELD 1-1/2 IN. (38 MM) MIN. OVERLAP SHEA THING VENT DEPTH FROM BACK OF APPLIANCE T O OUTSIDE SURF ACE OF EXTERIOR WALL (SEE CHART BELOW) SLIP SECTION CAN BE EXTENDED IN ...

  • Hearth and Home Technologies QV32B-A - page 49

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 49 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technician using Hearth & Home T echnologies speci fi ed and approved parts. B. Gas Pressure • Optimum appliance performance requires prop ...

  • Hearth and Home Technologies QV32B-A - page 50

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 50 B. Standing Pilot Ignition System Wiring • The standing pilot ignition system wiring does not require a 1 10 V AC supply to operate. See Figure 12.1. • A 1 10 V AC junction box MUST be installed for use with a fan or remote control. See Figure 12.2 for junction box wiring. Keep w ...

  • Hearth and Home Technologies QV32B-A - page 51

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 51 F . W all Switch Installation for Fan (Optional) If the box is being wired to a wall mounted switch for use with a fan (See Figure 12.3): • The power supply for the appliance must be brought into a switch box. • The power can then be supplied from the switch box to the appliance ...

  • Hearth and Home Technologies QV32B-A - page 52

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 52 A. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances as speci fi ed. Framing closer than the minimums list- ed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.). Figure 13.1 Minimum V ertical an ...

  • Hearth and Home Technologies QV32B-A - page 53

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 53 B. Facing Material • Metal front faces may be covered with non-combustible materials only . • Facing and/or fi nishing materials must not interfere with air fl ow through louvers, operation of louvers or doors, or access for service. • Facing and/or fi nishing materials must ...

  • Hearth and Home Technologies QV32B-A - page 54

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 54 A. Remove Fixed Glass Assembly See Section 14.G. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity . D. ...

  • Hearth and Home Technologies QV32B-A - page 55

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 55 F . Install the Log Assembly If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately , refer to the following instructions. 2014-925B 6/03 Log Set Assembly: LOGS-2014 Model: QV32B-A 4 5 1 2 3 STEP 1: Carefully remov ...

  • Hearth and Home Technologies QV32B-A - page 56

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 56 STEP 1: Carefully remove the logs from the packaging. CAUTION: Logs are fragile! 2016-925B 6/03 STEP 2: LOG #1 (SRV2016-701): Place notches of log #1 on outer two grate tines, and push against back of fi rebox. Log Set Assembly: LOGS-2016 Model: QV36B-A SAME SAME LOG LOG 4 5 1 2 3 1 ...

  • Hearth and Home Technologies QV32B-A - page 57

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 57 J. Install Hood The hood is shipped with the front/door . K. Air Shutter Setting Air shutter settings should be adjusted by a quali fi ed ser- vice technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for lon ...

  • Hearth and Home Technologies QV32B-A - page 58

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 58 A. Standing Pilot Ignition System 1 5 15 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed service technician in th ...

  • Hearth and Home Technologies QV32B-A - page 59

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 59 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. (Continued) C. V alve. T urn the valve knob to the ON position. Place the ON/ OFF switch in the ON position. T ake a reading with a millivolt meter at the thermopile terminals. The millivolt meter should read gr ...

  • Hearth and Home Technologies QV32B-A - page 60

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 60 1 6 16 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5. Figure 16.1 Appliance Dimensions A B T E ELECTRICAL ACCESS S V C D U G F H J I K Ø R Ø L M N O P Q ...

  • Hearth and Home Technologies QV32B-A - page 61

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 61 B. V ent Components Diagrams Figure 16.2 DVP vent components Pipe Effective Length Inches Millimeters DVP4 4 102 DVP6 6 152 DVP12 12 305 DVP24 24 610 DVP36 36 914 DVP48 48 1219 DVP6A 3 to 6 76 to 152 DVP12A 3 to 12 76 to 305 DVP12MI 3 to 12 76 to 305 DVP24MI 3 to 24 76 to 610 10-1/2 ...

  • Hearth and Home Technologies QV32B-A - page 62

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 62 DVP-TRAP1 DVP-TRAP2 DVP-TRAPK2 DVP-TRAPK1 DVP-TRAP Horizontal T ermination Cap 15-1/8 in. (384 mm) 12 in. (305 mm) 8 in. (203 mm) Max Effective Length Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in. to 7-1/4 in ...

  • Hearth and Home Technologies QV32B-A - page 63

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 63 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (127 mm) RF6M Roof Flashing Multi-pak 31 in. (787 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) RF12M Roof Flashing Multi-pak BEK Trap Ca p Brick Extension 13-3/4 in. (349 mm) 5 in. (127 mm) 13-3/4 in. (349 mm) Cap Shield DRC-RADIUS 13 ...

  • Hearth and Home Technologies QV32B-A - page 64

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 64 B. V ent Components Diagrams (continued) Figure 16.5 SLP Series V ent Components 8-3/4 in. 222 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 6 in. 152 mm 6-1/2 in. 165 mm 6-5/8 in. 168 mm 9-7/8 in. 251 mm 6-1/2 in. 165 mm 9-1/4 in. 235 mm SLP45 45° Elbow SLP90 90° Elbow Effective Height/ Le ...

  • Hearth and Home Technologies QV32B-A - page 65

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 65 B. V ent Components Diagrams (continued) Figure 16.6 SLP Series V ent Components SLP-SNKD Snorkel T ermination Cap SLP-TVHW V ertical T ermination Cap SLP-FLEX-TRAP Horizontal T ermination Kit SLP-CCS-BK Cathedral Ceiling Support Box-Black SLP-DCF-BK Ceiling Firestop Black SLP-WT -BK ...

  • Hearth and Home Technologies QV32B-A - page 66

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 66 Figure 16.7 Coaxial to Colinear V ent Components LINK-DV30B Flex Liner Kit DV -46DV A-GCL Coaxial/Colinear Appliance Connector COAXIAL to COLINEAR VENTING B. V ent Components Diagrams (continued) ...

  • Hearth and Home Technologies QV32B-A - page 67

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 67 C. Service Parts QV32B-A Beginning Manufacturing Date: June 2003 Ending Manufacturing Date: ______ R 32” Direct V ent Gas Fireplace IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial numbe ...

  • Hearth and Home Technologies QV32B-A - page 68

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 68 IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DESCRIPTION COMMENTS P ART NUMBER ...

  • Hearth and Home Technologies QV32B-A - page 69

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 69 #12 Burner/V alve Assembly Part number list on following page. 12.1 12.8 12.7 12.6 12.5 12.4 12.3 12.2 12.13 12.14 12.15 12.12 12.1 1 12.10 12.9 QV32B-A, QV36B-A Beginning Manufacturing Date: June 2003 Ending Manufacturing Date: ______ Service Parts R ...

  • Hearth and Home Technologies QV32B-A - page 70

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 70 C. Service Parts IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DESCRIPTION COMM ...

  • Hearth and Home Technologies QV32B-A - page 71

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 71 Service Parts QV32B-A, QV36B-A IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DE ...

  • Hearth and Home Technologies QV32B-A - page 72

    Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev . U • 1/12 72 Quadra-Fire, a brand of Hearth & Home T echnologies Inc. 7571 215 th Street West, Lakeville, MN 55044 www .quadra fi re.com D. Contact Information Please contact your Quadra-Fire dealer with any questions or concerns. For the location of your nearest Quadra-Fire dealer , please ...

Manufacturer Hearth and Home Technologies Category Indoor Fireplace

Documents that we receive from a manufacturer of a Hearth and Home Technologies QV32B-A can be divided into several groups. They are, among others:
- Hearth and Home Technologies technical drawings
- QV32B-A manuals
- Hearth and Home Technologies product data sheets
- information booklets
- or energy labels Hearth and Home Technologies QV32B-A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hearth and Home Technologies QV32B-A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hearth and Home Technologies QV32B-A, service manual, brief instructions and user manuals Hearth and Home Technologies QV32B-A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hearth and Home Technologies QV32B-A.

A complete manual for the device Hearth and Home Technologies QV32B-A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hearth and Home Technologies QV32B-A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hearth and Home Technologies QV32B-A.

A complete Hearth and Home Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hearth and Home Technologies QV32B-A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hearth and Home Technologies QV32B-A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hearth and Home Technologies QV32B-A, that we can find in the current document
3. Tips how to use the basic functions of the device Hearth and Home Technologies QV32B-A - which should help us in our first steps of using Hearth and Home Technologies QV32B-A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hearth and Home Technologies QV32B-A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hearth and Home Technologies QV32B-A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hearth and Home Technologies QV32B-A?

Use the form below

If you did not solve your problem by using a manual Hearth and Home Technologies QV32B-A, ask a question using the form below. If a user had a similar problem with Hearth and Home Technologies QV32B-A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)