English dropdown-ico

Manual Husqvarna 1340PW

33 pages 4.83 mb
Download

Go to site of 33

Summary
  • Husqvarna 1340PW - page 1

    200 8-0 2 O 0 8 07 301 5525PW, 602 7 PW, Operator's Manual Operator' s Manual Pressure Washer 903 2 PW, 13 40 PW ...

  • Husqvarna 1340PW - page 2

    English — 1 CONTENTS Contents CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 KEY TO SYMBOLS . . . . . . . . . . . . . . . . . . . . .2 Symbols in the Operator’ s Manual . . . . . . . . .2 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . .3 Dear Cust ...

  • Husqvarna 1340PW - page 3

    2 — English Safety Guidelines This manual contains information that is very important to know and understand. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. T o help recognize this information, observe the following symbols. W arning indicates a potentially hazardous situation which, if not avoided, COULD result in dea ...

  • Husqvarna 1340PW - page 4

    English — 3 INTRODUCTION Dear Customer , Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna River , for production of muskets. The location was logical, since waterpower was harnes ...

  • Husqvarna 1340PW - page 5

    4 — English WHA T IS WHA T? 1 Serial Number / Product Decal 2 T ip Holder with Spray Tips 3 Injection T ube Barb 4 Gun with T rigger 5 Lance 6 Inlet Connection for High Pressure Hose 7 Inlet Connection for Garden Hose 8 Engine Oil Fill 9 Engine switch - On/Off 10 Air Filter 11 Choke 12 Fuel T ank 13 Pressure Adjusting Knob 14 Fuel V alve - On/Off ...

  • Husqvarna 1340PW - page 6

    English — 5 FREQUENTL Y ASKED QUESTIONS How do I start my pr essur e washer? 1. Make sure you have gas and oil in the engine. 2. T urn the water on, then squeeze the trigger on the gun to make sure the water will flow smoothly out of the nozzle or tip. 3. Put the engine throttle control in the “Fast/Start” position. Set the fuel valve to “O ...

  • Husqvarna 1340PW - page 7

    6 — English SAFETY GUIDELINES Important Safety Instructions SA VE THESE INSTRUCTIONS The engine exhaust from this product contains chemicals known to the State of California to cause cancer , birth defects or other repr oductive harm. When using this product, basic precautions should AL WA YS be followed, including the following: • Read all ins ...

  • Husqvarna 1340PW - page 8

    English — 7 SAFETY GUIDELINES • Use only the nozzle supplied with this machine. • NEVER leave the wand unattended while the machine is running. • NEVER tamper with the engine governor or attempt to alter factory settings. Altering factory settings could damage the unit and will void the warranty . • AL WA YS hold gun and wand firmly when ...

  • Husqvarna 1340PW - page 9

    8 — English 2. Connect clear plastic hose to brass barb on pump (See Figure 2). 3. Secure garden hose (not included) to the inlet connection on pump (See Figures 3 and 4). PRE-OPERA TION UNP ACKING Remove the equipment and all parts from the carton. The carton should contain the following. • One pressure washer (pump, engine, cart base). • On ...

  • Husqvarna 1340PW - page 10

    English — 9 4. Connect the high pressure hose to the pump outlet (See Figure 4). 5. Attach the lance with nozzle to the gun (See Figure 5). 6. Install quick connect tip by pulling back on collar and pressing in tip. Release collar , make sure it completely returns to its forward position and tip is secure (See Figure 6). PRE-OPERA TION Figure 5 - ...

  • Husqvarna 1340PW - page 11

    10 — English PRE-OPERA TION TRIGGER SAFETY LA TCH In the engaged position, the trigger safety latch prevents the gun from being triggered accidentally . Pull the latch up to engage it (See Figure 9). AL WA YS engage the trigger safety latch when the unit is not in use. Figure 9 - T rigger lock T rigger lock (not engaged) T rigger lock (engaged) ...

  • Husqvarna 1340PW - page 12

    English — 11 OPERA TION 1. Surface Preparation AL WA YS engage the trigger safety latch when unit is not in use. The following cleaning procedure will help you organize your cleaning task and ensures that you will achieve the best results in the shortest amount of time. Remember to use the spraying / cleaning techniques mentioned in the following ...

  • Husqvarna 1340PW - page 13

    12 — English OPERA TION PRESSURE ADJUSTMENT Models 9032PW and 1340PW have a pressure adjustment knob located on the pump (see Figure 10). T urn the knob clockwise to increase the pressure. T urn the knob counter clockwise to decrease the pressure. DO NOT try and force the knob to turn. The knob may already be at either the lowest or highest setti ...

  • Husqvarna 1340PW - page 14

    English — 13 OPERA TION Spray water against a surface at a 45 degree angle to achieve the most beneficial impact force and to efficiently remove debris. DIST ANCE FROM CLEANING SURF ACE The distance between the spray nozzle and the cleaning surface is another factor that affects the impact force of the water . The impact force of the water increa ...

  • Husqvarna 1340PW - page 15

    14 — English OPERA TION GENERAL CLEANING TIPS 1. Apply the detergent so that it thoroughly covers the cleaning surface. Apply the detergent from bottom to top to prevent the detergent from sliding down and streaking. Wait a couple of minutes for the detergent to break down the dirt and grime. Use a brush to lightly scrub heavily soiled areas. NEV ...

  • Husqvarna 1340PW - page 16

    English — 15 OPERA TION 3. Disconnect the water supply and high pressure hose from the pump. 4. Allow the engine to cool. 5. Disconnect the spark plug wire and remove the spark plug. 6. Pour 1/2 oz. of engine oil into the spark plug hole. NEVER pull the starter rope on the engine when the spark plug is removed unless the spark plug hole is covere ...

  • Husqvarna 1340PW - page 17

    16 — English MAINTENANCE Observe regular maintenance intervals to ensure maximum performance and life from the pressure washer . Refer to the schedule for recommended maintenance. If you operate the pressure washer in dusty conditions, perform maintenance checks more often. ENGINE OIL CHANGING INSTRUCTIONS Before tipping the engine or equipment t ...

  • Husqvarna 1340PW - page 18

    English — 17 MAINTENANCE CHECKING PUMP OIL AND PUMP OIL CHANGING Checking oil level: Most pumps have either a sight glass or a dipstick (or both) to check the pump oil level. The cor rect oil level is at the center of the sight glass (center of red dot). The sight glass is usually located on the back side of the pump [See Figure 19 (B)]. For mode ...

  • Husqvarna 1340PW - page 19

    18 — English MAINTENANCE SCHEDULE Each use After first 5 hours of operation After first 50 hours of operation Every 25 hours of operation Every 50 hours of operation Each 100 hours of operation or every 3 months Every 500 hours of operation (5 months) • Check water inlet screen and filter . • Check engine and pump oil levels. Fill as necessar ...

  • Husqvarna 1340PW - page 20

    English — 19 TECHNICAL AND CONSUMER INFORMA TION Engine Oil T ype SAE 10W-30 SA E 30 W (Above 60 ° F/15.7° C) Engine Oil Capacity 5525PW - Honda GCV160 - 18.6 fl. oz. (0.550 L) 6027PW - Honda GX160 - 20 fl. oz. (0.591 L) 9032PW - Honda GX270 - 37 fl. oz. (1.090 L) 1340PW - Honda GX390 - 37 fl. oz. (1.090 L) Engine Fuel Capacity 5525PW - Honda G ...

  • Husqvarna 1340PW - page 21

    20 — English TROUBLESHOOTING CHAR T T roubleshooting Chart - Gasoline Power ed Pressure W ashers Only Symptom Possible Cause(s) Corrective Action(s) Engine will not start or is hard to start Engine misses or lacks power Low pressure and/or pump runs rough Water leakage from under pump manifold Water in pump crankcase (milky oil) Frequent or prema ...

  • Husqvarna 1340PW - page 22

    English — 21 TROUBLESHOOTING CHAR T Symptom Possible Cause(s) Corrective Action(s) Oil leakage between the engine and the pump Fluctuating pressure Pressure drops after period of normal use Pump noisy / pump runs rough Pressure washer will not spray detergent W orn oil seals and/or o-ring 1. Low engine oil 2. Pump valve worn, dirty or stuck 3. Pu ...

  • Husqvarna 1340PW - page 23

    SER VICE RECORD 22 — English Date Maintenance performed Replacement components requir ed ...

  • Husqvarna 1340PW - page 24

    English — 23 5525PW 531 30 75-38 Detergent T ube (not shown) * T ips sold separately; contact your dealer to purchase 505 27 16-01 531 30 74-97 531 30 74-84 531 30 75-35 531 30 74-69 531 30 74-96 505 19 45-24 531 30 75-41 (x2) 531 30 75-43 (x4) 531 30 75-28 531 30 75-31 531 30 75-30 531 30 75-32 531 30 74-61 (x2) 531 30 75-39 (x1) 531 30 81-11 (x ...

  • Husqvarna 1340PW - page 25

    24 — English 6027PW 505 19 45-40 505 27 16-02 505 19 45-42 531 30 75-44 531 30 74-87 531 30 74-68 531 30 74-86 531 30 75-39 (x1) 531 30 75-45 (x2) 531 30 75-47 531 30 74-91 531 30 74-95 531 30 55-49 (x2) 531 30 74-66 (x5) 505 19 45-39 531 30 74-60 Detergent T ube (not shown) 531 30 74-82 531 30 74-84 531 30 74-72 531 30 74-77 (Soap) 531 30 74-78 ...

  • Husqvarna 1340PW - page 26

    English — 25 9032PW & 1340PW 505 19 45-41 505 19 45-42 531 30 74-87 531 30 74-86 531 30 74-68 531 30 75-44 531 30 74-77 (Soap) 505 19 45-43 (0°) 505 19 45-44 (15°) 505 19 45-45 (25°) 505 19 45-46 (40°) 505 27 16-03 ( 9032PW) 505 27 16-04 ( 1340PW) 531 30 74-71 Detergent T ube (not shown) 531 30 74-82 531 30 74-84 531 30 74-72 531 30 75-39 ...

  • Husqvarna 1340PW - page 27

    26 — English Pump for 5525PW 505 27 18-01 Pump Assembly Complete 505 19 45-22 505 19 45-23 Key: P/O = Part Of KIt 505 19 45-21 505 19 45-20 P/O 505 19 45-02 505 19 45-18 P/O 505 19 45-09 505 19 45-17 505 19 45-16 505 19 45-15 505 19 45-14 505 19 45-13 505 19 45-12 505 19 45-11 505 19 45-10 P/O 505 19 45-09 P/O 505 19 45-09 P/O 505 19 45-06 P/O 50 ...

  • Husqvarna 1340PW - page 28

    English — 27 Pump for 6027PW 505 19 45-25 505 19 45-38 505 19 45-27 505 19 45-28 505 19 45-26 530 30 75-85 P/O 505 19 45-35 531 30 75-90 530 30 75-84 530 30 75-13 531 30 75-88 530 30 75-82 530 30 75-81 530 30 75-80 530 30 75-79 530 30 75-78 530 30 75-77 P/O 505 19 45-35 505 27 18-02 Pump Assembly Complete 531 30 75-16 505 19 45-29 505 19 45-31 53 ...

  • Husqvarna 1340PW - page 29

    28 — English Pump for 9032PW 531 30 74-83 Pump Oil (not shown) Key: P/O = Part Of KIt 505 19 45-27 505 19 45-38 P/O 505 19 45-35 505 19 45-49 505 19 45-48 (x3) 505 19 45-54 505 19 45-51 505 19 45-29 505 19 45-28 505 19 45-55 P/O 505 19 45-35 505 19 45-50 505 19 45-59 505 19 45-34 505 19 45-31 505 19 45-57 505 19 45-56 505 19 45-32 505 19 45-33 50 ...

  • Husqvarna 1340PW - page 30

    English — 29 505 19 45-63 505 19 45-68 505 19 45-62 505 19 45-64 P/O 505 19 45-67 505 19 45-65 P/O 505 19 45-67 531 30 74-83 Pump Oil (not shown) Key: P/O = Part Of KIt 505 19 45-66 Pump for 1340PW 505 19 45-69 531 30 75-25 531 30 75-26 531 30 75-24 505 19 45-79 531 30 75-20 531 30 75-21 531 30 75-22 505 19 45-68 531 30 75-19 505 19 45-79 505 19 ...

  • Husqvarna 1340PW - page 31

    30 — English NOTES ...

  • Husqvarna 1340PW - page 32

    English — 31 Pr o duct R egistra tion Notice! Ee c tiv e Ma y 1, 2 007 F AST! EAS Y! SIMPLE! Register your Husqvarna pr oduct on-line quickly and easily . Paper r egistration forms will not be accepted. There will be a grace period f or pr oducts built prior to January 1, 2007. All Husqvarna products can be register ed online regardless of the ...

  • Husqvarna 1340PW - page 33

    32 — English ...

Manufacturer Husqvarna Category Pressure Washer

Documents that we receive from a manufacturer of a Husqvarna 1340PW can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- 1340PW manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna 1340PW
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna 1340PW.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna 1340PW, service manual, brief instructions and user manuals Husqvarna 1340PW. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna 1340PW.

Similar manuals

A complete manual for the device Husqvarna 1340PW, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna 1340PW by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna 1340PW.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna 1340PW - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna 1340PW, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna 1340PW, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna 1340PW - which should help us in our first steps of using Husqvarna 1340PW
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna 1340PW
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna 1340PW in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna 1340PW?

Use the form below

If you did not solve your problem by using a manual Husqvarna 1340PW, ask a question using the form below. If a user had a similar problem with Husqvarna 1340PW it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)