English dropdown-ico

Manual Pelco ICI1000S Series

40 pages 0.43 mb
Download

Go to site of 40

Summary
  • Pelco ICI1000S Series - page 1

    Inter-Check ICI1000S Series Cash Register Interface System Installation/Operation Manual C1000M-B (1/96) ® PELCO • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981 FAX (800) 289-9150 or (1-559) 292-3827 ™ ® ...

  • Pelco ICI1000S Series - page 2

    TABLE OF CONTENTS Section Page 1.0 W ARNINGS ........................................................................................................................................ 1 2.0 SCOPE ............................................................................................................................................... 2 2.1 DESCRI ...

  • Pelco ICI1000S Series - page 3

    TABLE OF CONTENTS (Continued) Section Page 4.8 LOCA TION ID SETUP ........................................................................................................... .1 8 4.8.1 Location ID Program .................................................................................................. 18 4.8.2 Location ID On and Screen Position Se ...

  • Pelco ICI1000S Series - page 4

    LIST OF ILLUSTRA TIONS Figur e Page 1 Basic ICI1000S Configuration Wiring Diagram ............................................................................ 3 2 ICI1000PIM Wiring Configuration ............................................................................................... .4 3 Standard RS-232 Style Wiring Configuration ........... ...

  • Pelco ICI1000S Series - page 5

    Pelco Manual C1000M-B (1/96) 1 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. 1.0 W ARNINGS Prior to installati ...

  • Pelco ICI1000S Series - page 6

    2 Pelco Manual C1000M-B (1/96) In addition to the high performance and reliability you’ve come to expect from Pelco products, the Inter - Check ICI1000S Series of fers the following MAIN FEA TURES: • Monitors one device, cash register or A TM ma- chine. • Exception flagging for special alarm flags such as VOID or REFUND. • Exception flaggin ...

  • Pelco ICI1000S Series - page 7

    Pelco Manual C1000M-B (1/96) 3 Figure 1 . Basic ICI1000S Configuration W iring Diagram 3.0 INST ALLA TION T o begin installation, refer to the following instructions and Figures 1 and 2. 3.1 INST ALLING INTERF ACE CABLE 1. Install interface cable and PIM (if applicable) into the cash register according to the instructions sup- plied with your inter ...

  • Pelco ICI1000S Series - page 8

    4 Pelco Manual C1000M-B (1/96) Figure 3 . Standard RS-232 Style Wiring Configuration Figure 2. ICI1000PIM Wiring Configuration BL YL GR T o Inter-Check Unit Straight through phone cable User-supplied cable. 18 A WG shielded wire is suggested BL YL GR From ICI1000PIM BL YL GR T o Inter-Check Unit Straight through phone cable User-supplied cable. 18 ...

  • Pelco ICI1000S Series - page 9

    Pelco Manual C1000M-B (1/96) 5 Figure 4 . Printer Output and Alarm Input Wiring 3. Connect the data cable from the register interface cable (or PIM) to “DA T A IN” on the Inter -Check ICI1000S, using the ICI1000WK and 18 gauge, 2- conductor shielded cable (see Figure 1). 4. If using alarms, attach a 22-gauge, 2-conductor shielded cable from the ...

  • Pelco ICI1000S Series - page 10

    6 Pelco Manual C1000M-B (1/96) Figure 5 . Video Adjustment Locations 3.3 VIDEO ADJUSTMENTS All video adjustments are located on the bottom of the Inter -Check unit (refer to Figure 5). Using a non- metallic screwdriver, make any necessary adjustments as follows: • Horizontal Positioning adjusts the height of the displayed text. T o raise the text ...

  • Pelco ICI1000S Series - page 11

    Pelco Manual C1000M-B (1/96) 7 Figure 6 . Keypad Layout 1. Power down the Inter -Check ICI1000SI unit. 2. Remove the four cover screws with a Phillips screwdriver and set the cover aside. 3. Power up the ICI1000SI unit. 4. Program the Inter-Check unit for your particular application. 5. When finished programming, replace the cover and screw down fi ...

  • Pelco ICI1000S Series - page 12

    8 Pelco Manual C1000M-B (1/96) ICI1000S PROGRAMMING MENU TREE Monitoring Mode ↵ ENT Main Program Menu 1. Channel 1 Setup 2. System Parameters 3. Clock Setup 4. Location ID Setup 5. Customer Header 6. Diagnostics 7. Alarm Inputs Channel Program Menu 1. Communication Setup 2. Data Format/Communica- tion Protocol 3. V ideo Parameters 4. A TM Line Se ...

  • Pelco ICI1000S Series - page 13

    Pelco Manual C1000M-B (1/96) 9 4.3 CHANNEL SETUP There are two ways you can view your current channel parameters: 1. Press the “1” key on your keypad while in the monitoring mode. 2. Select CHANNEL SETUP (#1) in the MAIN PRO- GRAM MENU. After executing one of these steps, an example of what you might see is shown below: SELECTED: CHANNEL Pelco ...

  • Pelco ICI1000S Series - page 14

    10 Pelco Manual C1000M-B (1/96) 1=ASCII OR 2=EBCDIC The fifth prompt sets up the character set for the Inter - Check ICI1000S Series. Press a “1” to select ASCII and “2” for EBCDIC. The ASCII character set is the most common whereas EBCDIC is used predominantly in IBM systems. Select ASCII when connecting to a Pelco PIM. 1=DA T A NON INVERT ...

  • Pelco ICI1000S Series - page 15

    Pelco Manual C1000M-B (1/96) 11 4.5 VIDEO P ARAMETERS T o view the video parameters setting press #3 in the CHANNEL PROGRAM MENU. The Inter-Check ICI1000S Series will display the current settings. Press- ing ESC will skip the current line and allow you to con- tinue in the CHANNEL PROGRAM MENU. VIDEO P ARAMETER SETUP MENU SELECTED: NOR VID, OFF ID. ...

  • Pelco ICI1000S Series - page 16

    12 Pelco Manual C1000M-B (1/96) The next prompt is: ALARM DWELL TIME IN SECONDS (001-255)=? Simply enter in the amount of time you wish the alarm- ing output to remain active in seconds and press ENT . The following prompts allow you to activate the alarm- ing output upon the occurrence of data and/or an ex- ception on the channel. CHANNEL DA T A A ...

  • Pelco ICI1000S Series - page 17

    Pelco Manual C1000M-B (1/96) 13 4.6.5 Exception Alarm Settings Pr ogramming Exceptions EXCEPTIONS are situations of special inter - est that you can program into your Inter -Check ICI1000S Series unit. They are used to alarm your VCR or other alarmable devices when a certain condition has been met. Exceptions can also be directly printed to an exte ...

  • Pelco ICI1000S Series - page 18

    14 Pelco Manual C1000M-B (1/96) 4.6.6 Exception Alarm T ext Edit (Selection #6 in the System Program Menu) After Pressing #6 the following numbers will appear across your monitor screen: 12345678901234567890123456789012345678901234567890 = = This row of numbers is referred to as the Exception Column Line. This will aid you in programming vari- ous ...

  • Pelco ICI1000S Series - page 19

    Pelco Manual C1000M-B (1/96) 15 Exceptions Using the COLUMN SPECIFIC Strategy This is used to flag on specific placement of text on the register ticket. This type of exception uses the (^) character on your keypad. It is used to capture text ac- cording to the position on the register ticket. When this type of exception strategy is used, the Inter- ...

  • Pelco ICI1000S Series - page 20

    16 Pelco Manual C1000M-B (1/96) Exception Flagging Using WILDCARDS Used to flag on groups of transactions or departments. This type of exception also uses the caret (^) character and is usually used with the COLUMN SPECIFIC type of exception. Again, it is suggested that you use the EXCEPTION COLUMN LINE. EXAMPLE: Flag any transaction in your jew- e ...

  • Pelco ICI1000S Series - page 21

    Pelco Manual C1000M-B (1/96) 17 Notice that the second double bar is placed directly af- ter the data you are interested in. This format holds true for any transaction you wish to flag using the double bar format. The first double bar has a leeway of 15 char - acters or spaces. In other words, in the previous ex- ample the first double bar could be ...

  • Pelco ICI1000S Series - page 22

    18 Pelco Manual C1000M-B (1/96) 4.7.2 Clock ID On and Scr een Position Set Selection 2 in the CLOCK PROGRAM MENU will turn the clock on and allow positioning on the screen. Press the arrow keys twice for each increment to move the time and date to the preferred position and press ENT to save. 4.7.3 Clock ID Off The 3rd selection in the menu will tu ...

  • Pelco ICI1000S Series - page 23

    Pelco Manual C1000M-B (1/96) 19 4.8.2 Location ID On and Screen Position Set Pressing 2 in the LOCA TION ID SETUP MENU will turn the ID on at all times. It also allows you to posi- tion the ID with the cursor control keys to the desired screen display position. 4.8.3 Location ID Off Pressing 3 will turn of f the ID display . 4.9 CUSTOMER HEADER (Se ...

  • Pelco ICI1000S Series - page 24

    20 Pelco Manual C1000M-B (1/96) 4.10.4 Memor y T ests By entering 4 in this menu the following sub-menu is displayed: MEMOR Y TEST MENU 1. RAM TEST 2. VIDEO RAM TEST 3. (DL) NV MEMOR Y TEST 4. ROM CRC TEST By selecting 1, the unit will perform a self test on its Random Access Memory . This test is used to verify system RAM integrity . The system wi ...

  • Pelco ICI1000S Series - page 25

    Pelco Manual C1000M-B (1/96) 21 2. Press #6 (you will hear two tones). The following text will appear: DIAGNOSTICS SELECTION MENU 1. PROGRAM TRANSFER 2. (DL) BURN IN TEST 3. (DL) INPUT CHANNEL POR T TEST 4. MEMOR Y TESTS 5. SYSTEM SIGNAL TEST 6. VIDEO SCREEN TEST 7. GRAPHICS SCREEN TEST 8. (DL) Pelco PIM DEF AUL T LOAD ESC TO QUIT OR SELECT # TO PR ...

  • Pelco ICI1000S Series - page 26

    22 Pelco Manual C1000M-B (1/96) Figure 8 . Printer Output and Alarm Input Wiring 4.11 ALARM INPUT (Selection #7 from the main menu) The ALARM INPUT can be connected to any normally open (open loop) alarm device that can trigger a clo- sure for at least one-half second. Once an alarm is valid, the trigger is reset to open and will not detect the nex ...

  • Pelco ICI1000S Series - page 27

    Pelco Manual C1000M-B (1/96) 23 4.11.2 Alar m T rigger Dwell Selection #2 enables you to program the amount of time that the ALARM INPUT closure must be present in order for the Inter-Check ICI1000S Series to recognize it as a valid alarm condition. T o program this option, simply enter a suitable value between 000-255 seconds for the minimum durat ...

  • Pelco ICI1000S Series - page 28

    24 Pelco Manual C1000M-B (1/96) 6. Print the ALARM INPUT text via auxiliary port. Do this by selecting #4 (AUXILIAR Y PRINT LINK) in the ALARM INPUT PROGRAM MENU. AUX PRINT 1=OFF 2=ON 7. The descriptor will describe the type of action that caused the alarm. T o program the descriptor “REG. 1 OPEN”, enter #5 (ALARM TEXT) in the ALARM INPUT PROGR ...

  • Pelco ICI1000S Series - page 29

    Pelco Manual C1000M-B (1/96) 25 5.0 TROUBLESHOOTING Symptom: System does not receive register data. 1. Power down the PIM, then repower it. If you re- ceive a display on your monitor with a register model number , the unit is receiving data from the PIM. 2. Make sure the register model matches the number displayed on the monitor . 3. Make sure the ...

  • Pelco ICI1000S Series - page 30

    26 Pelco Manual C1000M-B (1/96) 5.1 TROUBLESHOOTING FLOW CHART ...

  • Pelco ICI1000S Series - page 31

    Pelco Manual C1000M-B (1/96) 27 6.0 SPECIFICA TIONS MODELS ICI1000SI Single register interface with inter - nal keypad for programming; one (1) alarm output and thirty (30) program- mable exceptions ICI1000SE Same as ICI1000SI except with ex- ternal keypad for programming ELECTRICAL Input V oltage: 5 VDC ± 3% Power Supply: Input 120 V AC @ 15 watt ...

  • Pelco ICI1000S Series - page 32

    28 Pelco Manual C1000M-B (1/96) 7.0 WARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1996, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, without charge, any merchandise proved defectiv ...

  • Pelco ICI1000S Series - page 33

    Pelco Manual C1000M-B (1/96) 29 APPENDIX A. HEXADECIMAL, DECIMAL AND BINAR Y CONVERSION TABLES 0 0 00000000 1 1 00000001 2 2 00000010 3 3 00000011 4 4 00000100 5 5 00000101 6 6 00000110 7 7 00000111 8 8 00001000 9 9 00001001 A 10 00001010 B 11 00001011 C 12 00001100 D 13 00001101 E 14 00001110 F 15 00001111 10 16 00010000 11 17 00010001 12 18 00010 ...

  • Pelco ICI1000S Series - page 34

    30 Pelco Manual C1000M-B (1/96) 64 100 01100100 65 101 01100101 66 102 01100110 67 103 01100111 68 104 01101000 69 105 01101001 6A 106 01101010 6B 107 01101011 6C 108 01101100 6D 109 01101101 6E 110 01101110 6F 111 01101111 70 112 01110000 71 113 01110001 72 114 01110010 73 115 01110011 74 116 01110100 75 117 01110101 76 118 01110110 77 119 0111011 ...

  • Pelco ICI1000S Series - page 35

    Pelco Manual C1000M-B (1/96) 31 C8 200 11001000 C9 201 11001001 CA 202 11001010 CB 203 11001011 CC 204 11001100 CD 205 11001101 CE 206 11001110 CF 207 11001111 D0 208 11010000 D1 209 11010001 D2 210 11010010 D3 211 11010011 D4 212 11010100 D5 213 11010101 D6 214 11010110 D7 215 11010111 D8 216 11011000 D9 217 11011001 D A 218 11011010 DB 219 110110 ...

  • Pelco ICI1000S Series - page 36

    32 Pelco Manual C1000M-B (1/96) Installation instructions for configuring the ICI1000PIM interface module are provided under separate cover in manual C1005M-D. If for some reason this manual is not readily available, refer to the following section to configure the switch settings on the PIM interface module, if applicable to your installation. DESC ...

  • Pelco ICI1000S Series - page 37

    Pelco Manual C1000M-B (1/96) 33 SWITCH BANK #2 This switch is dedicated to selecting which type of cash register the ICI1000PIM is interfacing with. The table below indicates the appropriate switch settings for a particular cash register . The first three settings indicate the appropriate settings for switches 1-3 on switch bank #1. A more detailed ...

  • Pelco ICI1000S Series - page 38

    34 Pelco Manual C1000M-B (1/96) Register Bank #1 Bank #2 Type Switch # Switch # Selection 1 2 3 1 2 3 4 5 6 7 8 NIXDORF ........................................................................................................................ .. + X + + - - + + + + + OMRON RS5550/RS5560 Dot Matrix Printer ............................................. ...

  • Pelco ICI1000S Series - page 39

    Pelco Manual C1000M-B (1/96) 35 Figure 9 . ICI1000PIM Switch Settings ICI1000PIM INST ALLA TION/ TROUBLESHOOTING GUIDELINES Listed below are some simple troubleshooting steps at your disposal. Following these steps will ensure that your Inter-Check P .O.S. unit is communicating correctly with your ICI1000PIM module. 1. Always execute a PIM DEF AUL ...

  • Pelco ICI1000S Series - page 40

    36 Pelco Manual C1000M-B (1/96) Pelco 3500 Pelco Way, Clovis, CA 93612-5699 (209) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (209) 292-3827 (Product specifications subject to change without notice.) C1000M-B ® ...

Manufacturer Pelco Category Cash Register

Documents that we receive from a manufacturer of a Pelco ICI1000S Series can be divided into several groups. They are, among others:
- Pelco technical drawings
- ICI1000S Series manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco ICI1000S Series
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco ICI1000S Series.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco ICI1000S Series, service manual, brief instructions and user manuals Pelco ICI1000S Series. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco ICI1000S Series.

Similar manuals

A complete manual for the device Pelco ICI1000S Series, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco ICI1000S Series by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco ICI1000S Series.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco ICI1000S Series - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco ICI1000S Series, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco ICI1000S Series, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco ICI1000S Series - which should help us in our first steps of using Pelco ICI1000S Series
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco ICI1000S Series
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco ICI1000S Series in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco ICI1000S Series?

Use the form below

If you did not solve your problem by using a manual Pelco ICI1000S Series, ask a question using the form below. If a user had a similar problem with Pelco ICI1000S Series it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)