Manual Allied Telesis AT-2701FXA/SC

94 pages 2.52 mb
Download

Go to site of 94

Summary
  • Allied Telesis AT-2701FXA/SC - page 1

    613-001847 Rev. A AT-2701 Series Adapters Fiber Fast Ethernet Adapters  A T -2701FXa/SC  A T -2701FXa/ST  A T -2701FTXa/SC  A T -2701FTXa/ST Installation and User’s Guide ...

  • Allied Telesis AT-2701FXA/SC - page 2

    Copyright © 2013 Allied T elesis, Inc. All rights reserved. No part of this publication may be repr oduced withou t prior written permissi on from Allied Telesis, Inc. Microsoft and Internet Explorer are regi stered trademarks of Microsoft Corpo rat ion. Netscape Navigator is a registered trademark of Netscape Communications Corporati on. Al l oth ...

  • Allied Telesis AT-2701FXA/SC - page 3

    3 Electrical Safety and Emissions St a n d a r d s This product meets the following standards: . RFI Emissions FCC Class B, EN55022 Class B, VCCI Class B, C-TICK, CE Immunity EN55024 Class B Electrical Safety EN60950-1 (TUV), UL 60950 -1 ( C UL US ) U.S. Federal Communications Commission Declaration of Conformity Manufacturer Name: Allied Telesis, ...

  • Allied Telesis AT-2701FXA/SC - page 4

    4 T ranslated Safety S tatements Important: The  indicates that a translation of th e safety statement is available in a PDF document titled “Translated Safety State ment s” posted on the Allied Telesis website at: www.alliedtelesis.com/support/ . ...

  • Allied Telesis AT-2701FXA/SC - page 5

    5 Contents Preface .............. .............. ............ .............. .............. .............. .............. .............. .............. ... ............. ............... .............. ......... 7 Safety Symbols Used in th is Docu ment........ .............. .............. .............. .............. .............. ............. . ...

  • Allied Telesis AT-2701FXA/SC - page 6

    Contents 6 Chapter 5: Modi fying Advanced Properties ................. .............. .............. .............. .............. .............. ............... ..............57 Overview ......... .............. .............. .............. .............. .............. .............. .............. ............ ...................... ........... ...

  • Allied Telesis AT-2701FXA/SC - page 7

    7 Pr eface This manual is the installation and us er’s guide for the AT-2701 Series Fiber Fast Ethernet Network Adapter cards. The adapter cards include d in this series are:  AT-2701FXa/SC  AT-2701FXa/ST  AT-2701FTXa/SC  AT-2701FTXa/ST The Preface contains t he following sections:  “Safety Symbols Used in this Document” o n pa ...

  • Allied Telesis AT-2701FXA/SC - page 8

    Preface 8 Safety Symbols Used in this Document This document uses the following conventions: Note Notes provide additional informatio n. Caution Cautions inform you t hat performing or omitting a spe cific action may result in equipment damage or loss of data. Warning Warnings inform you that performing or omitting a sp ecific action may result in ...

  • Allied Telesis AT-2701FXA/SC - page 9

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 9 Contacting Allied Telesis If you need assistance with this prod uct, you may contact Allied Telesis technical support by going to the Suppo rt & Services section of the Allied Telesis web site at www.alliedtelesis.com/support . You can find links for the following services on this page: ...

  • Allied Telesis AT-2701FXA/SC - page 10

    Preface 10 ...

  • Allied Telesis AT-2701FXA/SC - page 11

    11 Chapter 1 Overview This chapter provides an introduction to the Allied Te lesis AT-2701 series Fast Ethernet network adapter cards and contains the following sections:  “Description” on p age 12  “Model Naming Conventions” on page 15  “Features” on page 16  “Supported Operating Systems” on p age 17  “Accessing Do ...

  • Allied Telesis AT-2701FXA/SC - page 12

    Overview 12 Description The AT-2701 series adapters are Fiber Fast Etherne t PCI cards developed based on Realtek’s RTL8139 D Ethernet controller. The AT-2701 series adapter connects a computer to a Fast Ethernet network using fiber optic cabling and operates at 100 Mbp s full-duplex or half-duplex mode. The AT-2701 series offers the following mo ...

  • Allied Telesis AT-2701FXA/SC - page 13

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 13 SC Fiber Optic Adapter The AT-2701FXa/SC and AT-27 01FTXa/SC adapter cards are equipped with a 100BASE-FX port with the SC adapter. The SC adapter is shown in Figure 2. Figure 2. SC Fiber Optic Adapter To connect the SC adapter to a network cable, you must have a fiber optic network cable ...

  • Allied Telesis AT-2701FXA/SC - page 14

    Overview 14 LED The AT-2701FXa model comes with a single combination LED that indicates both the link status and activity statu s. The AT-2701FTXa model comes with two LED’s. One LED indicates the link status for either the copper or fiber port; the other indicates the activity status for the port with the valid link. Table 1 describes the link s ...

  • Allied Telesis AT-2701FXA/SC - page 15

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 15 Model Naming Conventions The hardware features of the AT-270 1 series adapter cards represen ted by the letters and numbers in the model names. The conventions for the AT-2701 adapter cards are identified in Fig ure 5. Figure 5. AT-2701 Model Naming Conventio ns The conventions are defined ...

  • Allied Telesis AT-2701FXA/SC - page 16

    Overview 16 Features The following list shows the features of the AT- 2701 series adapter cards:  One 100BASE-FX with an SC or ST fiber optic adapter  PCI version 2.2 interface  Pre-Execution Environment (PXE) 2.1 Remote Boot  Wa k e o n L A N ( W O L )  RoHS complia nt  Link/Activity LED ...

  • Allied Telesis AT-2701FXA/SC - page 17

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 17 Supported Operating Systems The following list shows the supported operating systems for the AT-2701 series adapter cards:  Windows 7  Windows XP  Linux Note To install driver software for W indows 7 and Windows XP, see Chapter 3, “Installing the Driver Softwar e for Windows” ...

  • Allied Telesis AT-2701FXA/SC - page 18

    Overview 18 Accessing Documents Documents for AT-2701 series adapter car ds are available at Allied Telesis websites. Allied Telesis Documents To access documents for AT-2701 series adapter ca rds, do the following: 1. Open a web browser , such as Internet Explorer or F ireFox, on your system and enter the following: http://www .alliedtelesis.com/ ...

  • Allied Telesis AT-2701FXA/SC - page 19

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 19 Contents of Your Shipment The following items are Incl uded with your adapter card:  Antistatic bag The adapter card is shipped in an antist atic bag. It protects the adapter card when stored or shipped. Keep the ada pter card in its p ackaging until ready for inst allation.  S tanda ...

  • Allied Telesis AT-2701FXA/SC - page 20

    Overview 20 Warranty Registration Allied Telesis hardware products are covered under limited warran ties. All Allied Telesis warranties are subjec t to and provided only on the terms and conditions set out in the Allied Telesis Limited Warranties listed on the Allied Telesis website at http://alliedtelesis.com/suppo rt/warranty . ...

  • Allied Telesis AT-2701FXA/SC - page 21

    21 Chapter 2 Installing the Hardwar e This chapter contains the following sections:  “System Requirements” on p age 22  “Reviewing Safety Precautions” on p age 23  “Pre-Installa tion Checklist” on p age 25  “Replacing the Bracket” on pag e 26  “Installing a Net work Adapter Card” on p age 28  “Connecting the ...

  • Allied Telesis AT-2701FXA/SC - page 22

    Installing the Hardware 22 System Requirements Before installing the AT-2701 Series Fiber Fast Ethernet Network Adapter cards, make sure your system meets the requirements listed below:  PC with one of the following op erating systems installed: – Windows XP – Windows 7 – Linux  One open PCI slot  128 MB RAM (minimum) ...

  • Allied Telesis AT-2701FXA/SC - page 23

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 23 Reviewing Safety Precautions Review the following safety precauti ons before you begin to install a module. Note The  indicates that a translation of the safety statement is available in a PDF document title d “Translated Safety Statements” posted on the Allied Telesis website at ww ...

  • Allied Telesis AT-2701FXA/SC - page 24

    Installing the Hardware 24 Warning The module is being installed in a system that operates with voltages that can be lethal. Before you remove the cover of your system, you must observe the following precaut ions to protect yourself and to prevent damage to the system compone nts. – Remove any metallic objects or jewelry from your han ds and wris ...

  • Allied Telesis AT-2701FXA/SC - page 25

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 25 Pre-Installation Checklist Before installing the AT-2701 series adapt er card, check the following list: 1. Check that your computer has an ap propriate open PCI slot. 2. Verify that your system is using the latest BIOS. 3. When you download the driver so ftware from the Allied Telesis web ...

  • Allied Telesis AT-2701FXA/SC - page 26

    Installing the Hardware 26 Replacing the Bracket The AT-2701 series adapter card is shipped with the low-profile bracket attached to the adapter. Depending on your system, you may need to replace the bracket attached to your adapter card. The following procedure describes how to remove the low-profile bracket from the adapter card and replace it wi ...

  • Allied Telesis AT-2701FXA/SC - page 27

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 27 Figure 7. Fastening Screws onto Standa rd Bracket ...

  • Allied Telesis AT-2701FXA/SC - page 28

    Installing the Hardware 28 Installing a Network Adapter Card The following instructions apply to installing an AT-2701 series adapter card in most systems. Refer to the manuals that were supplied with your system for details about performing t hese tasks on your particular system. To install the network adapter card, perfo rm the following procedur ...

  • Allied Telesis AT-2701FXA/SC - page 29

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 29 3. Select an empty, non-shared PCI slot an d remove the faceplate. Keep the faceplate in a safe place. Y ou may need it for future use. See Figure 9. Figure 9. Removing the Faceplate F rom PCI Slot Note If you cannot locate or know how to fin d a PCI slot, refer to the documentation that c ...

  • Allied Telesis AT-2701FXA/SC - page 30

    Installing the Hardware 30 Figure 10. Inserting the Netwo rk Adapter Card Caution Do not use excessive force when seating the card, as this may damage the system or the adapter ca rd. If the card resists seating, remove it from the system, realign it, and try again. 6. Secure the network ad apter card to the chassis with a Phillips-head screw (not ...

  • Allied Telesis AT-2701FXA/SC - page 31

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 31 9. Power the system on. Note If you installed the adapter card in Windows XP system before installing the drive r software, the Found New Hard ware Wizard launches automatically. For more informatio n, see Chapter 3, “Installing the Driver Software for Windows” on page 33. When the sys ...

  • Allied Telesis AT-2701FXA/SC - page 32

    Installing the Hardware 32 Connecting the Network Cables The AT-2701 series network adapter card is equipped with the SC or ST fiber optic adapter. To connect a network cable to the adapter, perform the following procedure: 1. Prepare a fiber optic ca ble with an appropriate connector to your adapter. Warning The fiber optic port s contain a Class ...

  • Allied Telesis AT-2701FXA/SC - page 33

    33 Chapter 3 Installing the Driver Softwar e for W indows This chapter describes how to install driver software for the AT-2701 series adapter onto your operating system . It contains the following topics:  “Overview” on page 34  “Downloading the Driver Sof tware for Windows” on p age 35  “Accessing the Device Manager” on p age ...

  • Allied Telesis AT-2701FXA/SC - page 34

    Installing the Driv er Software for Windows 34 Overview When you install the AT-2701 series adapter on your computer, you r next step is to install driver software for the adapter onto your Windows operating system. You can install driver software using De vice Manager or using the silent installation method. When you install deriver software using ...

  • Allied Telesis AT-2701FXA/SC - page 35

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 35 Downloading the Driver Software for Windows The AT-2701 series adapter is not shipped with a software drive r CD. You must download driver software from the Allied Telesis website. To download driver software, do the follo wing: 1. Open a web browser, such as Inte rnet Explorer or FireFox, ...

  • Allied Telesis AT-2701FXA/SC - page 36

    Installing the Driv er Software for Windows 36 . Figure 13. Specifying the Folder f or Unzipped Files 7. Specify the location of the folder and click Extract . 8. Record the location of the folder. ...

  • Allied Telesis AT-2701FXA/SC - page 37

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 37 Accessing the Device Manager When you install or update the driver software for AT-2701 series adapter, you must first access Device Manage r. The procedures for accessing Device Manager are slightly dif ferent among Windows operating systems. To access De vice Manager on your operating sy ...

  • Allied Telesis AT-2701FXA/SC - page 38

    Installing the Driv er Software for Windows 38 Figure 15. Device Manager Window on Windo ws 7 Accessing Device Manager on Windows XP To access Device Manager on Windows XP, do the following: 1. Right-click the My Computer icon on the desktop and select Properties . The System Properties window is opened as shown in Figure 16. Figure 16. System Prop ...

  • Allied Telesis AT-2701FXA/SC - page 39

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 39 2. Select the Hardware Tab. The Hardware p age is shown in Figure 17. Figure 17. Hardware Page on Windo ws XP 3. Click Device Manage r . The Device Manager window opens. Y our A T -2701 series adapter is detected as a Realtek de vice or Ethernet Controller as shown in Figure 18. Figure 18. ...

  • Allied Telesis AT-2701FXA/SC - page 40

    Installing the Driv er Software for Windows 40 Installing the Driver Software for Windows Once you physically install the AT-2701 series adapt er, the system detects the new hardware and creates a n entry in Device Manager when the Windows operating system first boots up. Shortly after you log in, you need to install the driver softwa re for your a ...

  • Allied Telesis AT-2701FXA/SC - page 41

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 41 3. Select Update Driver Software . The Update Driver Sof tware window pops up as shown in F igure 20. Figure 20. Update Driver Software Window o n Windows 7 4. Select Browse my computer for driver software . The Update Driver Sof tware window prompts you to enter th e location of the drive ...

  • Allied Telesis AT-2701FXA/SC - page 42

    Installing the Driv er Software for Windows 42 5. Specify the location of the driver software. See “Downloading the Driver Software for Windows” on p age 35 for details. 6. Click Next . The confirmation message shown in Figure 22 on p age 42 appears when the driver sof tware is successfully updated. Figure 22. Update Driver Software Window on W ...

  • Allied Telesis AT-2701FXA/SC - page 43

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 43 Figure 23. Ethernet Controller on Windows XP 3. Select Update Driver . The Hardware Update Wizard window pop s up as shown in Figure 24. Figure 24. Hardware Update Wizard 1 4. Select No, not this time . ...

  • Allied Telesis AT-2701FXA/SC - page 44

    Installing the Driv er Software for Windows 44 5. Click Next . The Hardware Update Wizard prompt s you to select one of two options as shown in Figure 25 Figure 25. Hardware Update W izard 2 6. Select Install from a list or specif ic location (Advanced) . 7. Click Next . The Hardware Update Wizard prompt s you to specify the location of your driver ...

  • Allied Telesis AT-2701FXA/SC - page 45

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 45 Figure 26. Hardware Update Wizard 3 8. Specify the location of the driver soft ware. 9. Click Next . The confirmation message is displayed as shown in Figure 27. Figure 27. Hardware Update Wizard 4 10. Click Finish . ...

  • Allied Telesis AT-2701FXA/SC - page 46

    Installing the Driv er Software for Windows 46 Updating the Driver Software for Windows To update the driver software, use the same pro cedure for installing the driver software for the first time. The only difference between updating and installing the driver software is the name of your adapter that Device Manager detects and lists. Device Manage ...

  • Allied Telesis AT-2701FXA/SC - page 47

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 47 Figure 28. Device Manager with an Expanded List on Wind ows 7 3. Select Update Driver Software . The Update Driver Softwa re window pops up as shown in Figure 20 on page 41. 4. Select Browse my computer for driver software . The Update Driver Sof tware window prompts you to enter th e loca ...

  • Allied Telesis AT-2701FXA/SC - page 48

    Installing the Driv er Software for Windows 48 The shortcut menu appears as shown in Figure 29. Figure 29. Network Adapters on Windows XP 3. Select Update Driver . The Hardware Update Wizard windo w pops up as shown in Figure 24 on page 43. 4. Select No, not this time . 5. Click Next . The Hardware Update Wizard prompt s you to select one of two op ...

  • Allied Telesis AT-2701FXA/SC - page 49

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 49 Performing the Silent Installation To simplify the driver installation process, you may p erform a silent installation when installing driver software for the AT-2701 series adapters. The silent installation is a meth od of installing software in the silent mode without constant interactio ...

  • Allied Telesis AT-2701FXA/SC - page 50

    Installing the Driv er Software for Windows 50 7. Change the directory to t he folder where the dpinst utility and the driver files reside. 8. Install the driver in the silent mode by entering the following command: > dpinst / S Note Adding the /S switch to the dpinst command suppresses the display of wizard pages, user dialog boxes, and other u ...

  • Allied Telesis AT-2701FXA/SC - page 51

    51 Chapter 4 Configuring the Ethernet Interface for Linux Systems This chapter provides procedures for configuring Ethernet interface s for AT-2701 series adapters on Lin ux systems and contains the following sections:  “Overview” on page 52  “Configuring an Ethernet Interface on Linux Systems” on p age 53 ...

  • Allied Telesis AT-2701FXA/SC - page 52

    Configuring the Ethe rnet Interface for Linux Sys tems 52 Overview When you use the AT-2701 series fiber optic adapt er on a PC with the Linux system, you must configure the Ethern et interface for the fiber optic port. Note If you install the AT-2701FTXa model and use the copper port, no changes in the Ethernet inter face are necessary. The AT-270 ...

  • Allied Telesis AT-2701FXA/SC - page 53

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 53 Configuring an Ethernet Interface on Linux Systems This section provides how to set the speed and d uplex mode to the Ethernet interfaces of AT-2701 series f iber optic adapters. The following is the general instructions for Ubuntu and Red Hat Linux distributions. For other distributions o ...

  • Allied Telesis AT-2701FXA/SC - page 54

    Configuring the Ethe rnet Interface for Linux Sys tems 54 6. Save the /etc/network/int erfaces file. 7. Reboot your Linux system. 8. Verify that your AT-2701 series adapter is running 100 Mbp s in the full- duplex mode by entering the following command: ethtool eth x The command output should display: Advertised Auto-Nego tiation is N o Speed is 10 ...

  • Allied Telesis AT-2701FXA/SC - page 55

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 55 ############ ######### ######### DEVICE="eth x " NM_CONTROLLE D="yes" ONBOOT=yes HWADDR= xx:xx:xx: xx:xx:xx TYPE=Etherne t BOOTPROTO=dh cp DEFROUTE=yes PEERDNS=yes PEERROUTES=y es IPV4_FAILURE _FATAL=ye s IPV6INIT=no NAME="auto e th x " ETHTOOL_OPTS ="aut ...

  • Allied Telesis AT-2701FXA/SC - page 56

    Configuring the Ethe rnet Interface for Linux Sys tems 56 ...

  • Allied Telesis AT-2701FXA/SC - page 57

    57 Chapter 5 Modifying Advanced Pr operties This chapter includes the following topics:  “Overview” on page 58  “Accessing Advanced Propertie s” on page 60  “Early Tx Threshold” on page 62  “Network Address (LAA)” on page 63  “PCI PME” on page 65  “S peed/Duplex” on pag e 67  “S peed/Duplex (100Mb Fibe ...

  • Allied Telesis AT-2701FXA/SC - page 58

    Modifying Advanced Properties 58 Overview The AT-2701 series adapter allows you to modify a dvanced properties to meet your requirements. To access the advanced properties, you must access Device Manager, then go to each advance d property page. Guidelines Here are the guidelines to m odifying the ad vanced properties:  To change the advanced pr ...

  • Allied Telesis AT-2701FXA/SC - page 59

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 59 Windows XP A T -2701FXa  “Early Tx Threshold” on p age 62  “Network Address (LAA)” on page 63  “S peed/Duplex” on page 67  “Vlan Id” on pa ge 70  “W ake-on-LAN” on page 71 A T -2701FTXa  “Early Tx Threshold” on page 62  “Network Address (LAA)? ...

  • Allied Telesis AT-2701FXA/SC - page 60

    Modifying Advanced Properties 60 Accessing Advanced Properties To modify advanced properties, first access Device Ma nager, open the properties of your AT-2701 series adapte r card, and select a feature you want to change its setting. 1. To access the Device Manager, follow one of these pro cedures:  “Accessing Device Manager on Wind ows 7” ...

  • Allied Telesis AT-2701FXA/SC - page 61

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 61 3. Click the Advanced tab. The Advanced Properties window opens as sho wn in Figure 31. Figure 31. Advanced Properties Window ...

  • Allied Telesis AT-2701FXA/SC - page 62

    Modifying Advanced Properties 62 Early Tx Threshold The Early Tx Threshold property allows you to control the FIFO buffer threshold. The system starts transmitting the data when the FIFO buffe r reaches the amount specified as the Early Tx Threshold. To change the value of Early Tx Thresh old, do the following: 1. Access the Advanced Properties. Se ...

  • Allied Telesis AT-2701FXA/SC - page 63

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 63 Network Addre ss (LAA) The Network Address (LAA) allows you to replace the MAC address originally assigned to the adapter with a user-defined address. The user- defined address that you assig n to the adapter is called a locally administered address (LAA). Caution A locally administered ad ...

  • Allied Telesis AT-2701FXA/SC - page 64

    Modifying Advanced Properties 64 Figure 33. Network Address (LAA) Page 3. In the Value text box, ent er a locally administered address for the AT-2701 series adapter card. By default, no locally a dmi nistered address is assigned. For more information, see “Guidelines for Assigning a Locally Administered Addr ess” on page 63. 4. Click OK . ...

  • Allied Telesis AT-2701FXA/SC - page 65

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 65 PCI PME The PCI PME (Power Manag ement Event) property enab les the Wake-on- LAN (WOL) function to wake the adapter up from a low-power mode, based on the settings of the “Wake on Magic Packet” and “Wake on Pattern Match” properties. For example, if the PCI PME and Wake on Magic Pa ...

  • Allied Telesis AT-2701FXA/SC - page 66

    Modifying Advanced Properties 66 3. Select one of the follo wing options:  Enable — The adapter wake s up from a low-power mode according to the settings of the Wake on Magic Packet a nd Wake on Pattern Match properties. Note When the Wake on Magic Packet and Wake on Pattern Match properties are both disabled, the adapt er stays in a low-power ...

  • Allied Telesis AT-2701FXA/SC - page 67

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 67 Speed/Duplex The Speed/Duplex property sets the link speed and duplex mode of the adapter. To change the Speed/Duplex property, do the following: 1. Access the Advanced Properties. See “Accessing Advanced Properties” on p age 60. 2. Select Speed/Duplex in the Property box. The S peed/D ...

  • Allied Telesis AT-2701FXA/SC - page 68

    Modifying Advanced Properties 68 Speed/Duplex (100Mb Fiber) The Speed/Duplex (100MB Fiber) property sets the link speed and duplex mode for the optic fiber adapter. To change the Speed/Duplex (100 MB Fiber) property, do the following: 1. Access the Advanced Properties. See “Accessing Advanced Propertie s” on page 60. 2. Select Speed/Duplex (100 ...

  • Allied Telesis AT-2701FXA/SC - page 69

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 69 Speed/Duplex (Copper) The Speed/Duplex (Copper) property sets the link speed and duplex mode for the twisted pair copper interface. To change the Speed/Duplex (Copper) property, do the following: 1. Access the Advanced Properties. See “Accessing Advanced Properties” on p age 60. 2. Sel ...

  • Allied Telesis AT-2701FXA/SC - page 70

    Modifying Advanced Properties 70 Vlan Id The Vlan Id property allows you to specify a VLAN ID on your network to the adapter. The adapter adds th e value of the VLAN ID to a frame in t he VLAN tag before transmitting the frame. To change the value of the Vlan Id, do the following: 1. Access the Advanced Properties. See “Accessing Advanced Propert ...

  • Allied Telesis AT-2701FXA/SC - page 71

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 71 Wake-on-LAN The Wake-on-LAN feature enables the network adapter to wake up from a low-power mode when the ada pter receives a network wake-up frame. To enable or disable the Wake-on-LAN feature, do the following: 1. Access the Advanced Properties. See “Accessing Advanced Properties” on ...

  • Allied Telesis AT-2701FXA/SC - page 72

    Modifying Advanced Properties 72 Wake on Magic Packet The Wake on Magic Packe t property specifies a condition when the adapter wakes up from a low-power mode. The ad apter wakes up when relieving a Magic Packet, if the Wake on Magic Packet and PCI PME properties are enabled. Note Even when you set the Wake on Mag ic Packet property to Enable , the ...

  • Allied Telesis AT-2701FXA/SC - page 73

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 73 3. Select one of the following options:  Enable — The adapter wakes up from a low-power mode when receiving a Magic Packet when th e PCI PME property is enabled.  Disable — The adapter stays in a low-power mode when receiving a Magic Packet. 4. Click OK . ...

  • Allied Telesis AT-2701FXA/SC - page 74

    Modifying Advanced Properties 74 Wake on Pattern Match The Wake on Pattern Match property specifies a condition when the adapter wakes up from a low-p ower mode. The adapter wakes up when a packet matches the wake patterns specified in the operating syste m, if the Wake on Pattern Match and PCI PME pro perties are enabled. Note Even when you set th ...

  • Allied Telesis AT-2701FXA/SC - page 75

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 75 3. Select one of the following options:  Enable — The adapter wakes up from a low-power mode when receiving a packet that matches one of the patterns specified in the operating system when the PCI PME property is enabled.  Disable — The adapter stays in a low-power mode when rece ...

  • Allied Telesis AT-2701FXA/SC - page 76

    Modifying Advanced Properties 76 ...

  • Allied Telesis AT-2701FXA/SC - page 77

    77 Chapter 6 Uninstalling the Driver Softwar e This chapter describes how to uninstall the driver so ftware for the AT-2701 series network adapters. This chapter contains the following to pics:  “Overview” on page 78  “Uninstalling t he Driver Software Using Device Mana ger” on page 79  “Uninstalling t he Driver Software Silently ...

  • Allied Telesis AT-2701FXA/SC - page 78

    Uninstalling the Driver Software 78 Overview When you no longer use the AT-2701 serie s adapter card for your computer, you may want to uninstall the drive r software from your operating system. As you can install driver software for the AT-2701 series adap ter card using Device Manager or the silent installation method, you can also uninstall driv ...

  • Allied Telesis AT-2701FXA/SC - page 79

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 79 Uninstalling the Driver Soft ware Using Device Manager To uninstall the driver software from you r operating system, do the following: 1. Start your Windows operating system and log in. 2. Access the Device Manager. See “Accessing the Device Manager” on p age 37. 3. In the Device Manag ...

  • Allied Telesis AT-2701FXA/SC - page 80

    Uninstalling the Driver Software 80 Uninstalling the Driv er Software Silently You can apply the silent installation method to uninstall the driver. Uninstall the driver without user-inter vention, perform th e following steps: 1. Open a command prompt window with administrator privileges. 2. Change the directory to t he folder where the dpinst uti ...

  • Allied Telesis AT-2701FXA/SC - page 81

    81 Chapter 7 T r oubleshooting This chapter describes troubleshooting p rocedures. It contain s the following sections:  “Checking the Port LED on the Adapter” on p age 82  “T roubleshooting Checklist” on page 83  “T esting Network Connectivity” on page 84 ...

  • Allied Telesis AT-2701FXA/SC - page 82

    Troubleshooting 82 Checking the Port LED on the Adapter The AT-2701 series adapter comes with one or two L ED’s, depending on the model. You can use the status of the port LED for troubleshooting. The AT-2701FXa model comes with a single combination LED that indicates both the link status and activity statu s. The AT-2701FTXa model comes with two ...

  • Allied Telesis AT-2701FXA/SC - page 83

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 83 Troubleshooting Checklist The following checklist provides recommended actions t o take to resolve problems installing the AT-2701 serie s network adapter card or running it in your system. Warning Before opening the cabinet of yo ur system for removing or inserting the adapter card, revie ...

  • Allied Telesis AT-2701FXA/SC - page 84

    Troubleshooting 84 Testing Network Connectivity This section describes how to test network connectivity f or Windows and Linux networks. Note When you are using the fiber optic port, both the adapter and the switch must be set to the same sp eed and duplex mode. When you are using the copper port, set both the adapter a nd switch to Auto- Negotiati ...

  • Allied Telesis AT-2701FXA/SC - page 85

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 85 Figure 44. Command Window with ip config/all displayed 4. Type ping <IP address> from the command line, then p ress Enter . The network connectivity informat ion is displayed, as sh own in Figure 45. Figure 45. Command Window with ping displayed Linux To verify that the Ethernet inte ...

  • Allied Telesis AT-2701FXA/SC - page 86

    Troubleshooting 86 To ping an IP host on the network to ve rify connection has been established, perform the following pro cedure. 1. From the command line, type ping <IP addre ss> . 2. Press Enter . The command displays the p acket send/receive st atus. ...

  • Allied Telesis AT-2701FXA/SC - page 87

    87 Appendix A Specifications Physical Specifications Dimensions: 12.5 cm x 6.4 cm (4.9 in. x 2.5 in.) Environmental Specifications Operating T emperature: 0°C to 40°C (+32°F to +104°F ) S torage T emperature: -25°C to +70°C (-°13F to +158°F) Relative Humidity: 5% to 90% (non-condensing) Power Specifications Signaling V oltage: 3.3 / 5V Powe ...

  • Allied Telesis AT-2701FXA/SC - page 88

    88 ...

  • Allied Telesis AT-2701FXA/SC - page 89

    89 Appendix B Cleaning Fiber Optic Connectors This appendix provides how to clea n fi ber optic connectors and consists of the following sections:  “Overview” on page 90  “Cleaning Using a Cartridge-T ype Clea ner” on page 91  “Cleaning Using a Swab” on p age 93 ...

  • Allied Telesis AT-2701FXA/SC - page 90

    90 Overview The fiber optic connector consists of a fiber optic plug and its adapter. The end of the fiber optic cable is held in the core of t he ferrule in the plug as shown in Figure 46. Light signals are transmit ted through the core of the fiber. Figure 46. Ferrule in an SC Connector Plug Even minor smudges or dirt on the end face of the fiber ...

  • Allied Telesis AT-2701FXA/SC - page 91

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 91 Cleaning Using a Cartridge-Type Cleaner Fiber optic cartridge cleaners are availa ble from many vendors and are typically called “cartridge cleaners,” as shown in Figure 48. Figure 48. Cartridge Cleaner Note Do not use compressed air or aerosol air to clean a fiber optic connector. To ...

  • Allied Telesis AT-2701FXA/SC - page 92

    92 Note Rub the ferrule tip on the clea ning surface in one direction only. 3. When you reach the end of the cleaning surface, pick up the ferrule tip, rotate and place it at the top and ru b downwards at least 2 times. Caution Failing to pick up the ferrule tip when you reach the bottom of the cleaning surface can result in static electricity tha ...

  • Allied Telesis AT-2701FXA/SC - page 93

    AT-2701 Series Fast Ethernet Adapter Installation Gui de 93 Cleaning Using a Swab Specially treated swabs (stick cleaner s) are available for cleaning inside connector adapters or hard-to-reach ferrule tips. These swabs, ofte n referred to as “lint free” or “alcohol fre e” swabs, are available from many vendors. See Figure 50. Stick cleaner ...

  • Allied Telesis AT-2701FXA/SC - page 94

    94 3. If a fiber inspection scope is avail able, use the scope to inspect th e connector to make sure that it is clea n. 4. Reconnect the cable t o the port or protect the ferr ule tip with a dust cap. ...

Manufacturer Allied Telesis Category Network Card

Documents that we receive from a manufacturer of a Allied Telesis AT-2701FXA/SC can be divided into several groups. They are, among others:
- Allied Telesis technical drawings
- AT-2701FXA/SC manuals
- Allied Telesis product data sheets
- information booklets
- or energy labels Allied Telesis AT-2701FXA/SC
All of them are important, but the most important information from the point of view of use of the device are in the user manual Allied Telesis AT-2701FXA/SC.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Allied Telesis AT-2701FXA/SC, service manual, brief instructions and user manuals Allied Telesis AT-2701FXA/SC. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Allied Telesis AT-2701FXA/SC.

A complete manual for the device Allied Telesis AT-2701FXA/SC, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Allied Telesis AT-2701FXA/SC by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Allied Telesis AT-2701FXA/SC.

A complete Allied Telesis manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Allied Telesis AT-2701FXA/SC - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Allied Telesis AT-2701FXA/SC, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Allied Telesis AT-2701FXA/SC, that we can find in the current document
3. Tips how to use the basic functions of the device Allied Telesis AT-2701FXA/SC - which should help us in our first steps of using Allied Telesis AT-2701FXA/SC
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Allied Telesis AT-2701FXA/SC
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Allied Telesis AT-2701FXA/SC in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Allied Telesis AT-2701FXA/SC?

Use the form below

If you did not solve your problem by using a manual Allied Telesis AT-2701FXA/SC, ask a question using the form below. If a user had a similar problem with Allied Telesis AT-2701FXA/SC it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)