English dropdown-ico

Manual John Deere ET-3303-J

16 pages 0.1 mb
Download

Go to site of 16

Summary
  • John Deere ET-3303-J - page 1

    3 1/4-Inch Belt Sander Operator's Manual 1 CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! THIS MANUAL IS AN IMPORTANT PART OF THE BELT SANDER AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT. ET -3303-J 3 1/4-INCH BEL T SANDER ...

  • John Deere ET-3303-J - page 2

    2 3 1/4-Inch Belt Sander Operator's Manual Congratulations on the purchase of your new Belt Sander! You can be assured your belt sander was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance. This operator's manual was compiled for your benefit ...

  • John Deere ET-3303-J - page 3

    3 1/4-Inch Belt Sander Operator's Manual 3 T able of Content SAFETY .................................................................................................................. 4-9 GENERAL SAFETY RULES .................................................................. 4-9 FUNCTIONAL DESCRIPTION ........................................... ...

  • John Deere ET-3303-J - page 4

    4 3 1/4-Inch Belt Sander Operator's Manual W ARNI N G W A R N I NG SI N T HE M A NUA LS . W A RN I NG SI N T HE M A NUA LS . CA U T I ON OC A UT I ON S IN O T H E M A N UA L S OC AUT I ON S IN O T H E M A N UA L S OC AUT I ON S IN O T H E M A N UA L S OC A UT I ON S IN O T H E M A N UA L S RECOGNIZE SAFETY INFORMATION This is the safety alert ...

  • John Deere ET-3303-J - page 5

    3 1/4-Inch Belt Sander Operator's Manual 5 KEEP WORK AREA CLEAN AND WELL LIT. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT . Don't expose power tools to rain. Don't use power tools in damp or wet locations. Keep work area well lit. Don't use tool in presence of flammable liquids or gases. Power too ...

  • John Deere ET-3303-J - page 6

    6 3 1/4-Inch Belt Sander Operator's Manual DON'T OVERREACH Keep proper footing and balance at all times. MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and replace if damaged, have repaired by authorized ser ...

  • John Deere ET-3303-J - page 7

    3 1/4-Inch Belt Sander Operator's Manual 7 OUTDOOR USE EXTENSION CORDS When tool is used outdoors, use only extension cords intended for use outdoors and so marked. STAY ALERT Watch what you are doing. Use common sense. Do not operate tool when you are tired. CHECK DAMAGED PARTS Before further use of the tool, a guard or other part that is dam ...

  • John Deere ET-3303-J - page 8

    8 3 1/4-Inch Belt Sander Operator's Manual POLARIZED PLUGS To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electricia ...

  • John Deere ET-3303-J - page 9

    3 1/4-Inch Belt Sander Operator's Manual 9 EXTENSION CORD Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table shows the correct size to ...

  • John Deere ET-3303-J - page 10

    10 3 1/4-Inch Belt Sander Operator's Manual Functional Description MODEL: ET-3303-J 3 1/4-INCH BELT SANDER NAME OF PARTS: (Fig. 1a) (Fig. 1b) NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless ...

  • John Deere ET-3303-J - page 11

    3 1/4-Inch Belt Sander Operator's Manual 11 Operation APPLICATIONS: - Sanding finish and flooring finish of woodwork products. - Base polishing of Lumber-coated planes. - Sanding finishes of metal surfaces. - Base polishing of metal-coated planes, rust removal, or paint removal to refinishing. - Surface finish of slate, concrete, and so on. PR ...

  • John Deere ET-3303-J - page 12

    12 3 1/4-Inch Belt Sander Operator's Manual OPERATION: HOW TO USE THE BELT SANDER: 1. How to adjust sanding position: Push switch and turn sanding belt to check position. Adjust sanding belt so that both edges protrude 1/6” - 1/8” (1.6mm-3mm) past edges of pulleys. If sanding belt is operated too far on the inside, it may cause abrasion an ...

  • John Deere ET-3303-J - page 13

    3 1/4-Inch Belt Sander Operator's Manual 13 OPERATION (CONTINUED): 6. How to change belt speed: Either high speed or low speed operation can be selected according to the materials or the operating conditions. Selecting sanding belt operating speed can be achieved by shifting the tumbler switch in a specified direction. 7. How to operate switch ...

  • John Deere ET-3303-J - page 14

    14 3 1/4-Inch Belt Sander Operator's Manual MAINTENANCE AND INSPECTION: CAUTION: BE SURE TO SWITCH POWER OFF AND DISCONNECT THE PLUG DURING MAINTENANCE AND INSPECTION. 1. Inspecting the Sanding Belts: If the sanding belt becomes loaded with debris or dull, the efficiency will drop significantly. It may be necessary to clean or replace the sand ...

  • John Deere ET-3303-J - page 15

    3 1/4-Inch Belt Sander Operator's Manual 15 NOTE: Due to JOHN DEERE’s continuing program of research and development, the specifications herein are subject to change without prior notice. SERVICE AND REPAIRS All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These operations should ONLY b ...

  • John Deere ET-3303-J - page 16

    16 3 1/4-Inch Belt Sander Operator's Manual Manufactured for Deere & Company, Moline, Illinois 61265 3 1/4-Inch Belt Sander Operator's Manual 110 Code No. C99110661 N #37-0691-090403 © Copyright 2003. John Deere ...

Manufacturer John Deere Category Sander

Documents that we receive from a manufacturer of a John Deere ET-3303-J can be divided into several groups. They are, among others:
- John Deere technical drawings
- ET-3303-J manuals
- John Deere product data sheets
- information booklets
- or energy labels John Deere ET-3303-J
All of them are important, but the most important information from the point of view of use of the device are in the user manual John Deere ET-3303-J.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals John Deere ET-3303-J, service manual, brief instructions and user manuals John Deere ET-3303-J. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product John Deere ET-3303-J.

Similar manuals

A complete manual for the device John Deere ET-3303-J, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use John Deere ET-3303-J by users. Manuals are usually written by a technical writer, but in a language understandable to all users of John Deere ET-3303-J.

A complete John Deere manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual John Deere ET-3303-J - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the John Deere ET-3303-J, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the John Deere ET-3303-J, that we can find in the current document
3. Tips how to use the basic functions of the device John Deere ET-3303-J - which should help us in our first steps of using John Deere ET-3303-J
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with John Deere ET-3303-J
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of John Deere ET-3303-J in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning John Deere ET-3303-J?

Use the form below

If you did not solve your problem by using a manual John Deere ET-3303-J, ask a question using the form below. If a user had a similar problem with John Deere ET-3303-J it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)