Manual Dell M8024-k

56 pages 2.66 mb
Download

Go to site of 56

Summary
  • Dell M8024-k - page 1

    Author s Network Enabled S olutions Team, Kevin Locklear Contributor Kili Land Deployin g FCoE ( FIP Snoopi ng) on Dell PowerConn ect 10G Sw itches: M8024- k, 8024 and 8024 F A Dell Deploymen t Guide ...

  • Dell M8024-k - page 2

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 2 This document is for informational p u rposes only and may contain typographical er r ors and technical ina c curacies. The content is provided as is, with out express or i mplied war r an t ies o f any kind. © 2011 - 2012 Dell I nc. All rights re served ...

  • Dell M8024-k - page 3

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 3 Contents Introduction ........................................................................................................... 6 Basic Termin ology .................................................................................................... 6 F ...

  • Dell M8024-k - page 4

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 4 Cisco Nexus 5 548UP CLI examp l e .............................................................................. 52 Appendix B - Network Switch V e r s ions ........................................................................... 56 References ........ ...

  • Dell M8024-k - page 5

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 5 ...

  • Dell M8024-k - page 6

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 6 Introduction The PowerConnect™ M8024 - k, 8024 and 80 24 F switches are n ow DCB/DCBx c apable with a downloadable update . Start ing w ith firmware 4.2, the latest PowerConnect™ 10 Gigabit switches can now be used as an FCoE Transit S witch (FIP S no ...

  • Dell M8024-k - page 7

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 7 PFC Priority Flow Control (PFC) , or Per - Priority Pause i s defined in the IEEE 802.1Qb b standard. PFC i s flow control bas e d on priority s ettings and a d d s ad d itional in f or mation to th e standard pau se frame. The additional f ie lds added t ...

  • Dell M8024-k - page 8

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 8 Configuration s cenarios The following s ections will present very bas ic e x amples of de ploying the 10G switches for FIP Snoopin g and will provide step -by- step e xp l anations of the C LI commands as a guide. The GUI does not cur r e n tly support c ...

  • Dell M8024-k - page 9

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 9 Important notes pri o r to deplo y me nt No Simple Mode Each of the fol lowing scen ar i os in this docu ment assume that the PowerConnect™ 8024 mode l switch being used is in normal Switch Mode (not Simple Mo de) and is using firmwar e version 4. 2. x. ...

  • Dell M8024-k - page 10

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 10 Scenario 1: Depl o yi ng th e Dell PowerCo nnect 8 024 Series F SB in a Cisco 5 000 Series Switch (NPIV ) environment T his first exa mple is a basic , single connection betw een devi ces example using the Dell PowerConnect M8024 -k . This configurat ion ...

  • Dell M8024-k - page 11

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 11 The flowch ar t in Figure 8 is a g e n e r al overvie w of h ow the dep l oyment will oc c ur. This incl u des the basic plann in g that will n e e d t o take place in order for most of the steps in t h e rest of the d ocu ment to fall into place. Genera ...

  • Dell M8024-k - page 12

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 12 Figure 9 is a gr ap h ical repr e se n t ation of how many of the con f iguration p ie ce s ar e considered parallel settings. M os t of the confi g u r at ion will d e p e n d h eavily on con f igurations b e ing complet ed in more than just one place. ...

  • Dell M8024-k - page 13

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 13 Configuring th e Dell PowerConne ct M8024 - k,8024, and 8024F for FIP Sn ooping The Dell PowerConnect 8024 model swit ches wil l mo nit or FIP packets and will establish the proper filtering, an d prioritie s f or the FCoE t r a ffic that is pa ssed thro ...

  • Dell M8024-k - page 14

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 14 Step by Step explanati on of CLI example o Configure – this brings the prompt into the configuration interface o no mode simple – puts switch into n or mal mode o vlan database - moves d o wn into the VLA N dat abase inte r f a ce  vlan 20 – add ...

  • Dell M8024-k - page 15

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 15 o i nterface te1/0/20 – this moves into the inter f a ce te1/0/20 c onfiguration  switchport general pvid 20 – est ab l ishes the nat iv e VLAN as 20, you mu st remove V LA N 1 in order for this to functi on correctly  switchport general allow ...

  • Dell M8024-k - page 16

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 16 Configuration overvie w of Dell PowerConnect M8024 - k Figure 9. ...

  • Dell M8024-k - page 17

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 17 Con figuring the Cisco 5000 se r ies s witch with firmware ver 5.x for a sing le connection from t he Dell PowerConnect M8024 - k or 8024()(F) The CLI comman ds below are nece ssary for an un - configured C isco 5020. The CLI will show ad d it ional line ...

  • Dell M8024-k - page 18

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 18 The follow in g CLI comman ds are necess ary for an un - conf igured Cisc o Ne xus 5548UP or C i sco Nexus 5596. The full CLI will show additional lines that a re either default or can’t be changed and are not added for thi s example. T h e C LI will a ...

  • Dell M8024-k - page 19

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 19 St ep by Step explanati on of the CLI example  Configure – this brings y ou into the con figuration interface . o feature FCOE – enabl e s t h e feature for FC OE as long as the l icensing an d FC modules are installed . o feature NPIV – enables ...

  • Dell M8024-k - page 20

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 20 o Zone name blade1 vsan 2 – this will set the name for your zone (blade1 can be any chosen name); vsan 2 will match t he vsan you have cr e ated.  Member interface fc2/1 - th is adds the fc2/1 in t erface as a me mber of the zo ne.  member pwwn x ...

  • Dell M8024-k - page 21

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 21 M1000e Chassis Manage ment Controller - > Server Ove rview - > Properties -> Figure 13. WWN/MAC inf ormation for Blade Server 3’s “B” fabric CNA port 2 (B 2). ...

  • Dell M8024-k - page 22

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 22 Basic Validat ion f or the Cisco Nex us 5000 series switch configurat ion With connect ions made vi a fiber opti c c able or direct connect cabl e (twin - ax) the basi c c onnectivity on the port between the two switches can be verif ied. These cables or ...

  • Dell M8024-k - page 23

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 23 Check the spanning tree configu r ation. Blocking ports should be understood and when they show in this entry it should be the number expected. Otherwise it could be tha t an unintentional cable loop has been created that will need to be resol ved. Type ...

  • Dell M8024-k - page 24

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 24 With all cables in place between the switches and the FC /FCoE SAN, use the following command s to validate you r configurati on. First check g eneral statu s of the ports, and links by u sin g: SHOW I NTERFA CE ST ATU S Show interface status r esults Fi ...

  • Dell M8024-k - page 25

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 25 With the SHOW SPANNIN G - TREE BLOCKEDPORTS command t he status of po r t s t hat may be impa cted by spanning tree can be checked. This is also a good point to make sure that the spanning - tree behaviors are as expect ed, such as Prior ity, which switc ...

  • Dell M8024-k - page 26

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 26 The follow in g command wi ll show a set of vit al information on the DCBX configuration. T ype: SHOW LLDP DCB X INT ERFACE ALL . The important things to note with this command are that the configuration source sele cted is “True ” and that the conf ...

  • Dell M8024-k - page 27

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 27 The follow in g command wi ll show a set of v it al information on the DCBX configuration. T ype: SHOW LLDP DCB X INT ERFACE TE 1/0/2 0 DETAIL . This command will sh ow more spec if ic detail ab ou t the configuration that has been negotiated between the ...

  • Dell M8024-k - page 28

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 28 Finally , after the se val idation step s , go into the di sk management in t erface of t h e se r v e r . I f the SAN is configured appropriatel y the server w ill have an av ailable LUN t o use for stor age. Basic Troubl eshooting Areas Problem Potenti ...

  • Dell M8024-k - page 29

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 29 Problem Potential Problem Area Potential Fix The VFC entries may no t be present on the Cisco Nexus 5000 series switch Ensure that VFC's are created that will be applicable to the connection. This can be bound to the FCoE- FIP MAC of the CNA or to t ...

  • Dell M8024-k - page 30

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 30 S cenario 2: Configuring Multiple Uplinks into LAG for Cisco N exus 5000 Series Switch ( NPIV ) Environment Multiple port l ink (LAG) configurat ion between swit ches and storage Figure 23. ...

  • Dell M8024-k - page 31

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 31 Configuring the Cisc o Nexus 5000 serie s switch with f irmware ver 5.x for a multiple link LAG (link aggregation) connection at the Top - of - Ra ck. The typical s cenario in a b usiness envir onment cons i st s of more than one connection or uplink. Th ...

  • Dell M8024-k - page 32

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 32 Step by Step explanati on of CLI example (only covering the differences from the single port configuration) o interface vfc1 – selects virtual fc interface vfc1 (vfc1 is an exam ple and can be a different number based on choice at configuration time) ? ...

  • Dell M8024-k - page 33

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 33 Configuring the M80 24 - k,8024, and 80 24F for FIP Snooping This is an exa mple of the nece s sary CLI comm ands for 8024 mo del switche s configure d with two l in k s in a LAG or port - channel uplin k ed to the Cisco 50 20. This prov ides more bandw ...

  • Dell M8024-k - page 34

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 34 Step by Step explanati on of Dell PowerConn ect M8024- k CLI example w ith mult iple port (LAG) uplink ( this only cov ers the differenc es from the single p ort configurati on). o interface te1/0/19 – this moves into the interface te1/0/19 configurati ...

  • Dell M8024-k - page 35

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 35 S cenario 3: Configuring Multiple Uplinks into LAG for Cisco Nexus 5000 Series Switch ( NPV mode) Environme n t Multiple link configuration bet ween switches and storage Figure 26. ...

  • Dell M8024-k - page 36

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 36 Configuring the Cisc o Nexus 5000 seri es switch with firmwa re ver 5.0(3)N2(2a) in NPV mode for a multiple lin k LAG (link aggregation ) connection from t he Dell PowerCo n nect M8024 - k or 8024 ()( F) The typical s cenario in a b usiness envir onment ...

  • Dell M8024-k - page 37

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 37 Step by Step explanati on of CLI example for th e Cisco Nexus 5000 Seri es using NPV (only covering the differences from t he single port c onfiguration) o feature NPV – enables the NPV feature which turns off zoning . T he FC side of the Nexu s 5000 s ...

  • Dell M8024-k - page 38

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 38 F urther notes on ETS / CoS behav ior settings Careful consideration should be taken when establishing the strict priority queues and managing bandwidth re servations. I t FCoE and iSC SI are configu red on the same sw itch and th e se se t tings are use ...

  • Dell M8024-k - page 39

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 39 Updating f irmware NOTE:. Be sure to check the Releas e Notes and any special in structions t h at may have come with new firmwar e updates. It is i mportant t o follow inst ructions foun d in those do cuments if th e y deviate from this white paper. Ste ...

  • Dell M8024-k - page 40

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 40 Perform an ot her show version c ommand to con fir m th at the new fir mware has been downloaded to the switch. Not ice that the firmware was copied in to the inactiv e image for e ach member. The current - active colum n now shows th e same values as th ...

  • Dell M8024-k - page 41

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 41 To validate, l ogin to the s witch and per for m a show version comman d . For the exa mple given the following i s displayed. While downgr ading to a pre v i ous firmw ar e i s supporte d , all features an d f u n ctions that w ere not part of the previ ...

  • Dell M8024-k - page 42

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 42 3. Enter the IP address of the TFTP serve r into the Server Address field, and enter th e name of the Firmware file into the S ource File Name f ield. 4. If not in th e r oot directory of the TFTP serve r, enter th e p at h of the firmware file. 5. Click ...

  • Dell M8024-k - page 43

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 43 Also notice that the switch still has the same Current - Active image as before . 8. Under the Next - Active col umn, select t h e n ew image (i. e . image2) for the sw itch or st ack . 9. Click Apply . The Current - Active colum n should now sh ow the o ...

  • Dell M8024-k - page 44

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 44 Notice that the new firmware (i.e. 4.2.0.4 ) is now the Current - Active image for e ach member. While downgr ading to a pre v i ous firmw ar e i s supporte d , all features an d f u n ctions that w ere not part of the previous firmware will be lost, inc ...

  • Dell M8024-k - page 45

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 45 Appendix A – F ull CLI ex a mpl es M8024 - k CLI example show running - config !Current Configuration: !System Description "PowerConnect M8024 - k, 4.2.1.3, VxWorks 6.6" !System Software Version 4.2.1.3 !Cut- through mode is configured as dis ...

  • Dell M8024-k - page 46

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 46 ! interface Te1/0/2 cos- queue min - bandwidth 0 0 0 50 0 0 0 cos- queue strict 3 shutdown spanning - tree port - priority 0 mtu 2500 switchport mode general switchport general pvid 20 switchport general allowed vlan add 20 switchport general allowed vla ...

  • Dell M8024-k - page 47

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 47 exit ! interface Te1/0/6 cos- queue min - bandwidth 0 0 0 50 0 0 0 cos- queue strict 3 shutdown spanning - tree port - priority 0 mtu 2500 switchport mode general switchport general pvid 20 switchport general allowed vlan add 20 switchport general allowe ...

  • Dell M8024-k - page 48

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 48 lldp dcbx port - role auto - down exit ! interface Te1/0/10 cos- queue min - bandwidth 0 0 0 50 0 0 0 cos- queue strict 3 shutdown spanning - tree port - priority 0 mtu 2500 switchport mode general switchport general pvid 20 switchport general allowed vl ...

  • Dell M8024-k - page 49

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 49 switchport general allowed vlan add 1000 tagged switchport general allowed vlan remove 1 lldp dcbx port - role auto - down exit ! interface Te1/0/14 cos- queue min - bandwidth 0 0 0 50 0 0 0 cos- queue strict 3 shutdown spanning - tree port - priority 0 ...

  • Dell M8024-k - page 50

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 50 mtu 2500 switchport mode general switchport general pvid 20 switchport general allowed vlan add 20 switchport general allowed vlan add 1000 tagged switchport general allowed vlan remove 1 exit ! interface Te1/0/18 cos- queue min - bandwidth 0 0 0 50 0 0 ...

  • Dell M8024-k - page 51

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 51 switchport general allowed vlan add 1000 tagged switchport general allowed vlan remove 1 mtu 2500 fip- snooping port - mode fcf exit ! interface port - channel 3 mtu 2500 exit ! interface port - channel 4 mtu 2500 exit  Skipped port - channel 5 throug ...

  • Dell M8024-k - page 52

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 52 Cisco Nexus 5548 UP CLI example Technet5548 - 1# show running - config !Command: show running - config !Time: Tue Feb 14 22:47:07 2012 version 5.0(3)N2(2a) feature fcoe feature telnet cfs ipv4 distribute feature lacp feature lldp username admin password ...

  • Dell M8024-k - page 53

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 53 vlan 1000 fcoe vsan 2 name FCoE_VLAN vsan database vsan 2 interface port - channel2 switchport mode trunk switchport trunk native vlan 20 switchport trunk allowed vlan 1000 interface vfc3 bind mac - address 14:fe:b5:8e:5b:f2 no shutdown interface vfc4 bi ...

  • Dell M8024-k - page 54

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 54 interface fc1/32 switchport trunk mode on no shutdown interface Ethernet1/1 interface Ethernet1/2 interface Ethernet1/3 interface Ethernet1/4 interface Ethernet1/5 interface Ethernet1/6 interface Ethernet1/7 interface Ethernet1/8 interface Ethernet1/9 in ...

  • Dell M8024-k - page 55

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 55 interface Ethernet1/25 interface Ethernet1/26 switchport mode trunk switchport trunk native vlan 20 switchport trunk allowed vlan 1000 interface Ethernet1/27 switchport mode trunk switchport trunk native vlan 20 switchport trunk allowed vlan 1000 interfa ...

  • Dell M8024-k - page 56

    Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switche s: M8024 - k, 8024, and 8024F 56 Appendix B - Network Switch Versions Version info rmation for the ne twork switches us ed in creating t his document are as follows: Switch Firmw are Versions Table 1. Network switch Dell PowerConnect™ M8024k Dell PowerC onnect ™ 8024/8024F C is c o ...

Manufacturer Dell Category Riding Toy

Documents that we receive from a manufacturer of a Dell M8024-k can be divided into several groups. They are, among others:
- Dell technical drawings
- M8024-k manuals
- Dell product data sheets
- information booklets
- or energy labels Dell M8024-k
All of them are important, but the most important information from the point of view of use of the device are in the user manual Dell M8024-k.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Dell M8024-k, service manual, brief instructions and user manuals Dell M8024-k. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Dell M8024-k.

Similar manuals

A complete manual for the device Dell M8024-k, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Dell M8024-k by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Dell M8024-k.

A complete Dell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Dell M8024-k - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Dell M8024-k, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Dell M8024-k, that we can find in the current document
3. Tips how to use the basic functions of the device Dell M8024-k - which should help us in our first steps of using Dell M8024-k
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Dell M8024-k
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Dell M8024-k in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Dell M8024-k?

Use the form below

If you did not solve your problem by using a manual Dell M8024-k, ask a question using the form below. If a user had a similar problem with Dell M8024-k it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)