Manual Carrier 500 T/R

30 pages 1.1 mb
Download

Go to site of 30

Summary
  • Carrier 500 T/R - page 1

    INSTALLATION AND USER’S MANUAL External and internal temperature recorders DataCOLD 500 T/R Carrier Transicold Europe – 10, Bd de l’Oise – 95031 Cergy Pontoise Cédex – France Carrier Transicold North America, 700 Olympic Drive, Ath ens, Ga. 30601 - U.S.A. Carrier Refrigeration Operation 2003 Printed in France 02-03 / 62-61138-20 ...

  • Carrier 500 T/R - page 2

    Page 2 62-61138-20 (0 2/03) INTRODUCTION This manual is a guideline for the installation and use of the DataCOLD 500 T/R temperature recorders. To avoid loss of warranty coverage due to incompetent installation it is most essential to follow the instructions and recommendations of this manual. DataCOLD 500 T/R recorders are developed and produced t ...

  • Carrier 500 T/R - page 3

    Page 3 62-61138-20 (0 2/03) TABLE OF CONTENTS 1 GENERAL D ESCRIPTION .......................................................................................................... ...................... 4 1.1 LCD Di splay................................................................................................................ .................... ...

  • Carrier 500 T/R - page 4

    1 General description The control panel of the DataCOLD 500 T/R consists of three main components: 1- LCD Display 2- Key board 3- Printer 1.1 LCD Display The display has four lines of information, s howing the following content in the operating mode: Page 4 62-61138-20 (0 2/03) Line 1: Alarm active; temperatures, status of the digital inputs  - ...

  • Carrier 500 T/R - page 5

    1.3 Printer The thermal printer is installed in the right side of the recorder. Due to the so called “Plug and Play concept” the printer can be retrofitted, at any time, without disconnec ting the recorder from power. For retrofit, the existing mechanism will be exchanged for a mechanism with printer. To remove the printer or the housing, press ...

  • Carrier 500 T/R - page 6

    Page 6 62-61138-20 (0 2/03) Digital Inputs The digital inputs allow control and regist ration of doors (open/close) or defrost or refrigeration (on/off) or any other digital input information following the configuration of the recorder. By confi guring the parameters the interpretation of the corresponding status can be distinguished. Power supply ...

  • Carrier 500 T/R - page 7

    12 Core cable Tem p erature in p uts Lt. blue Whit e Whit e Yellow CON4 – Tem p erature in p uts Pink Lt. Blue Gre y Yellow Di g ital in p uts Gre y Pink Violet Brown Orange Violet Blue Green Brown CON3 – Di g itals in p uts Orange Blue Green Red Black Optional Mounting kit If no radio slot is available, the recorder should be mount ed with the ...

  • Carrier 500 T/R - page 8

    Page 8 62-61138-20 (0 2/03) DataCOLD T-Version The T-Version has been designed for outside mounting dire ctly on the body. Usually it is fixed under the refrigeration unit on the front side of the body, where it is easily accessible. For fixing proceed as follows: First hold the box in the desired position and mark the mounting holes . Next step is ...

  • Carrier 500 T/R - page 9

    WARNING : DISCONNECT THE RECORDER FROM THE BATTERY IF THE REFRIGERATION UNIT IS NOT USED FOR MORE THAN TEN (10) DAYS. Page 9 62-61138-20 (0 2/03) ...

  • Carrier 500 T/R - page 10

    - Display background lighting (preferable for the R-Version) Usually the display background light switches on after pr essing any key and switching off automatically after 30 seconds. When a permanent background light is required while driving connect pin 3 to a vehicle ignition +signal. WARNING : NEVER CONNECT DIRECT TO THE BATTERY. - Alarm output ...

  • Carrier 500 T/R - page 11

    Page 11 62-61138-20 ( 02/03)  Changing the language 1. Press the green key and select menu 3.4 with ↑ , ↓ . 2. Press again the green key to edit (enter) the menu 3.4. 3. Select the desired language with < …> and validate with the green key. 4. Press the red key to return to the normal display.  Programming the vehicle ID No. and t ...

  • Carrier 500 T/R - page 12

    Page 12 62-61138-20 ( 02/03) 3 User menu's DataCold 500 T/R have four different user menu’s, which are directly accessible via the keyboard: 1. Print menu 2. Alarm menu 3. User settings menu 4. Status menu 3.1 Print menu Press Blue button. The last selected print choice will be displayed. Printing starts after 2 seconds. Repeatedly pressing ...

  • Carrier 500 T/R - page 13

    Page 13 62-61138-20 ( 02/03) ‘Print time period’ is set to “0 hour“ only the ‘Day start time’ is applicable. ...

  • Carrier 500 T/R - page 14

    Page 14 62-61138-20 ( 02/03) 3.1.7 Day start time A print out starts from the actual time and goes backwards until the time set in this parameter, unless the ‘Print time period’ is shorter. If the ‘Day start time’ is set to “00:00” only the ‘Print period time’ is applicable. This allows you to print back to a maximum of 24 hours. 1. ...

  • Carrier 500 T/R - page 15

    3.3 User settings With the user settings several adjustments can be done to offer the user a maximum of user convenience. By pressing the green button the user setting menu will be activated. Toggle with [ ↑ ], [ ↓ ] between the available menu’s (3.1; 3.2; 3.3; …). Between ‘(..)’ the actual setting is disp layed. With [edit] you enter t ...

  • Carrier 500 T/R - page 16

    < > accept <-cncl 3.3.6 Display back light setting Set the intensity of the back light to your convenience. The light switches on when you press any button and switches off after 30 seconds. 3.5 Display back light setting < > accept <-cncl 3.3.7 Keyboard back light setting Set the intensity of the back light to your convenience. T ...

  • Carrier 500 T/R - page 17

    Page 17 62-61138-20 ( 02/03) The display scrolls the compartments which ar e activated in menu 7 (Compartment settings). Remarks: If there is a communication problem with the serial port of the refrigeration unit or if the refrigeration unit is switched off, the message “Unit connection lost” is displayed. If the refrigeration unit is switched ...

  • Carrier 500 T/R - page 18

    Page 18 62-61138-20 ( 02/03) T3 Input >on/off. Menu structure as 5.1 T4 Input >on/off. Menu structure as 5.1 ...

  • Carrier 500 T/R - page 19

    Page 19 62-61138-20 ( 02/03) Menu 6 : Digital inputs settings 4 inputs for status recording, any input can be switched on/off, assigned with a name and a polarity. A number of names are available as a factory setting, to be selected from a list. In the operating mode you can see on the display which i nputs are activated. An empty small box indicat ...

  • Carrier 500 T/R - page 20

    Page 20 62-61138-20 ( 02/03) Menu 8 : Alarm settings 4 Alarm groups– each with a name to assign, upper- and lower temperature limit and a delay time. Each enabled alarm type can be activated by the user for any compartment, although per compartment only one alarm group can be set at the same time. 8.1 Alarm group 1 >on/off 8.1.1 Name >Froze ...

  • Carrier 500 T/R - page 21

    Page 21 62-61138-20 ( 02/03) Menu 10 : General settings General settings for identifying the unit. 10.1 Temperature units >C The units that temperatures will be disp layed. Either degrees C, or degrees F. 10.2 Sample rate >10 minutes The interval time in Minutes (1, 2, 3,..,15, 20, 25, 30,.., 60 minutes) for storing a temperature measurement ...

  • Carrier 500 T/R - page 22

    Page 22 62-61138-20 ( 02/03) 11.2 COM2 RS-232 port setting Refer to Enclosure E: wiring diagrams to connect the CO M2 RS-232 port of the recorder to the micro of the refrigeration unit. • No protocol. • Third party: light protocol to extrac t part of the data from the recorder. • TMS protocol (9,600 Baud): current protocol to extract all data ...

  • Carrier 500 T/R - page 23

    Page 23 62-61138-20 ( 02/03) 5 Accessories and spare parts ITEM PART NUMBER DESIGNATION NS 12-00585-50 Connection Infra-Red cable for PC 1. 12-00585-51 Aluminium guard for sensor NS 12-00585-52 Handheld probe 16’ ( 5 M ) cable & junction box NS 12-00585-53 Magnetic Door Switch (rear door) NS 12-00585-54 Magnetic Door Switch (side door) 2. 12- ...

  • Carrier 500 T/R - page 24

    Page 24 62-61138-20 ( 02/03) ...

  • Carrier 500 T/R - page 25

    Page 25 62-61138-20 ( 02/03) Enclosure A Technical data a) Technical specification: • Operating voltage : 10-36 Volts DC, prot ected against alternator load shedding. • Power consumption: Nominal 0. 6W, max. 25W (while printing) • Temperature : -22°F to +158°F (-30°C / +70°C) be in operation, -40°F to +185°F (-40°C / +85°C) while in s ...

  • Carrier 500 T/R - page 26

    Enclosure B Replace paper roll If a coloured line appears on the last meter of paper , the paper roll needs to be replaced as follow : 1- Push lock lightly upwards and pull the printer module carefully forward. 2- Open the upper part of the front panel. 3- Insert a new paper roll on the spindle. 4- Place the printer module carefully back into the r ...

  • Carrier 500 T/R - page 27

    Page 27 62-61138-20 ( 02/03) Enclosure C Factory settings 5. Temperature inputs Factory setting 5.1. T1 input On 5.1.1. Type Temperature 5.1.2. Name Return Air 5.2. T2 input On 5.2.1. Type Temperature 5.2.2. Name Rear 5.3. T3 input Off 5.4. T4 input Off 6. Digital Inputs 6.1. D1 Input Off, Refrigeration 6.2. D2 Input Off, Back door 6.3. D3 Input Of ...

  • Carrier 500 T/R - page 28

    Enclosure D Failure codes & Set correction factor procedure If the display shows one of the following values: OC (I) the input is activat ed but no sensor is connected. (ii) the sensor has an open circui t (sensor or wire failure.) SC (I) the sensor has a shor t (sensor or cable failure.) Procedure to set a Correction factor The DataCOLD 500 R/ ...

  • Carrier 500 T/R - page 29

    Enclosure E Wiring diagrams CONNECTOR 1 POWER SUPPLY & DIGITAL OUTPUTS 1 = POWER SUPPLY (+) 2 = POWER NEGATIVE (-) 3 = DISPLAY BACKLIGHT (+) 4 = ALARM O/P TEMP 5 = ALARM O/P DIGIT battery Ignition key (+) (display backlight) WARN ING : NEVER CONNECT DISPLA Y BA CKLIGHT DIRECTLY TO THE BATTERY CONNECTOR 3 DIGITAL INPUTS (configuration example) 1 ...

  • Carrier 500 T/R - page 30

    CONNECTOR 2 RS232 a) Serial communication w ith micro of th e refrigeration unit w ithout control panel 1 = GND 2 = RXD 3 = TXD 4 = CTS 5 = RTS Communication cable 3 way P/N : 22-60633-00 Unit microprocessor connector DataCOLD 500 b) Serial communication w ith micro of the refr igeration unit w ith one control panel and “Y” communication cable ...

Manufacturer Carrier Category Weather Radio

Documents that we receive from a manufacturer of a Carrier 500 T/R can be divided into several groups. They are, among others:
- Carrier technical drawings
- 500 T/R manuals
- Carrier product data sheets
- information booklets
- or energy labels Carrier 500 T/R
All of them are important, but the most important information from the point of view of use of the device are in the user manual Carrier 500 T/R.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Carrier 500 T/R, service manual, brief instructions and user manuals Carrier 500 T/R. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Carrier 500 T/R.

Similar manuals

A complete manual for the device Carrier 500 T/R, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Carrier 500 T/R by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Carrier 500 T/R.

A complete Carrier manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Carrier 500 T/R - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Carrier 500 T/R, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Carrier 500 T/R, that we can find in the current document
3. Tips how to use the basic functions of the device Carrier 500 T/R - which should help us in our first steps of using Carrier 500 T/R
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Carrier 500 T/R
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Carrier 500 T/R in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Carrier 500 T/R?

Use the form below

If you did not solve your problem by using a manual Carrier 500 T/R, ask a question using the form below. If a user had a similar problem with Carrier 500 T/R it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)