Manual Skil 2372

44 pages 0.52 mb
Download

Go to site of 44

Summary
  • Skil 2372 - page 1

    IMPORT ANT : IMPORT ANT : IMPORT ANTE: Read Before Using Lire avant usage Leer antes de usar Operating/Safety Instructions Consignes de fonctionnement/sécurité Instrucciones de funcionamiento y seguridad 2362 2372 2 1 3 4 5 For English Version Version française Versión en español See pa ge 2 Voir page 16 Ver la página 30 1-877-SKIL999 (1-877- ...

  • Skil 2372 - page 2

    -2 - Work area safety Keep work area clean and well lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. Keep children and bystanders away while operating a power tool. Distraction ...

  • Skil 2372 - page 3

    -3- SAVE THESE INSTRUCTIONS Keep handles dry, clean and free from oil and grease. Slippery hands cannot safely c ontrol the power tool. Power tool use and care Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. Do not use the po ...

  • Skil 2372 - page 4

    -4- Safety Rules for Cordless Drill / Drivers Hold power tools by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. Use clamps or other practical way to secure and support the workpiec ...

  • Skil 2372 - page 5

    -5- Safety Rules for Cordless Power Wrenches Hold power tools by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. Do not dr ill , fa ste n o r break into existing walls or other blind ...

  • Skil 2372 - page 6

    -6- When batteries are not in tool or charger, keep them away from metal objects. For example, to protect terminals from shorting DO NOT place batteries in a tool box or pocket with nails, screws, keys, etc. Fire or injury may result. DO NOT PUT BATTERIES INTO FIRE OR EXPOSE TO HIGH HEAT. They may explode. ! WARNING Battery Care Charging the Tool W ...

  • Skil 2372 - page 7

    BATTERY REMOVAL INSTRUCTIONS Run motor until battery is completely discharged before attempting to remove battery from your tool. 1. Loosen the nut with a large wrench in direction of arrow (A) and completely unthread nut. 2. Remove head assembly and nut from the tool. 3. Pull and remove metal front end in direction of arrow (B) to expose and remov ...

  • Skil 2372 - page 8

    -8- IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Symbol Name Designation/Explanation V Volts Voltage (potential) A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power kg Kilogra ...

  • Skil 2372 - page 9

    Model numbe r 2362 Voltage rating 7.2 V No load speed n 0 0-500/min Charger 1619X03241 Voltage rating 120 V 60 Hz Charge time 3-5 hours Maximum Capacities Chuck size 1/4" Hex-shank with power groove Drilling wood 3/8" (10 mm) Mild metal 1/4" (6 mm) Screw sizes 1/4" (6 mm) -9- Functional Description and Specifications – 2362 Ba ...

  • Skil 2372 - page 10

    VARIABLE SPEED CONTROLLED TRIGGER SWITCH Your tool is equipped with a variable speed trigger switch. The tool can be turned "ON" or "OFF" by squeezing or releasing the trigger. The speed can be adjusted from the minimum to maximum nameplate RPM by the pressure you apply to the trigger. Apply more pressure to increase the speed a ...

  • Skil 2372 - page 11

    -11- ADJUSTABLE CLUTCH Your tool features 11 clutch settings. Output torque will increase as the clutch ring, is rotated from 1 to 10. The drill “ ” position will lock up the clutch to permit drilling and driving heavyduty work, and also enables bits to be changed quickly and easily in the keyless chuck (Fig. 3). BRAKE When the trigger switch i ...

  • Skil 2372 - page 12

    DRILL BITS Always inspect drill bits for excessive wear. Use only bits that are sharp and in good condition. TWIST BITS: Available with straight and reduced shanks for wood and light duty metal drilling. High speed bits cut faster and last longer on hard materials. CARBIDE TIPPED BITS: Used for drilling stone, concrete, plaster, cement and other un ...

  • Skil 2372 - page 13

    Model numbe r 2372 Voltage rating 7.2 V No load speed n 0 200/min Charger 1619X03241 Voltage rating 120 V 60 Hz Charge time 3-5 h our s Maximum Capacities Output drive 1/4" drive Bolt capacity 3/8" Screw driving in wood: 1/4" screws Manual Torque 400 in-lbs -13- Functional Description and Specifications – 2372 Disconnect battery pa ...

  • Skil 2372 - page 14

    -14- (POWER MODE) TRIGGER "ON-OFF" SWITCH TO TURN THE TOOL "ON" squeeze the trigger switch. TO TURN THE TOOL "OFF", release the trigger switch, which is spring loaded and will return to the "OFF" position automatically (Fig. 7). The power mode is only intended to run bolts and nuts down and snug up. The power ...

  • Skil 2372 - page 15

    -15- Maintenance Service NO USER SERVICEABLE PARTS INSIDE. Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recom- mend that all tool service be performed by a Skil Factory Service Center or Authorized Skil Service Station. SERVICEMEN: Disconnec ...

  • Skil 2372 - page 16

    -16- Sécurité du lieu de travail Maintenez le lieu de travail propre et bien éclairé. Les risques d’accident sont plus élevés quand on travaille dans un endroit encombré ou sombre. N’utilisez pas d’outils électroportatifs dans des atmosphères explosives, comme par exemple en présence de gaz, de poussières ou de liquides inflammable ...

  • Skil 2372 - page 17

    -17- Maintenez les poignées sèches et exemptes d’huile et d e graisse. O n ne pas maîtriser un outil électroportatif e n toute sécurité quand on a les mains glissantes. Utilisation et entretien des outils électroportatifs Ne forcez pas sur l’outil électroportatif. Utilisez l’outil électroportatif qui convient à la tâche à effectue ...

  • Skil 2372 - page 18

    -18- Consignes de sécurité pour perceuses/tournevis sans cordon Tenez les outils électroportatifs par les surfaces isolées de préhension en exécutant une opération au cours de laquelle les outils de coupe peuvent venir en contact avec les fils cachés. Le contact avec un fil sous tension rendra les pièces métalliques exposées de l'ou ...

  • Skil 2372 - page 19

    -19- Consignes de sécurité pour les boulonneuses sans fil Tenez les outils électroportatifs par les surfaces isolées de préhension en exécutant une opération au cours de laquelle les outils de coupe peuvent venir en contact avec les fils cachés. Le contact avec un fil sous tension rendra les pièces métalliques exposées de l'outil so ...

  • Skil 2372 - page 20

    -20- Lorsque la pile est déchargée, l'outil est mis automatiquement hors service par le déclenchement d'un circuit de protection : l'outil cesse alors de fonctionner. Pour éviter d'endommager la pile, ne continuez pas à appuyer sur l'interrupteur de marche/arrêt après que l'outil a été mis hors service automat ...

  • Skil 2372 - page 21

    -21- Ne tentez pas de désassembler le bloc-piles ou d’enlever tout composant faisant saillie des bornes de piles, ce qui peut provoquer un incendie ou des blessures. Avant la mise au rebut, protégez les bornes exposées à l’aide d’un ruban isolant épais pour prévenir le court-circuitage. PILES LITHIUM-ION Si le produit est équipé d&apo ...

  • Skil 2372 - page 22

    -22- Symboles IMPORTANT : Certains des symboles suivants peuvent être utilisés sur votre outil. Veuillez les étudier et apprendre leur signification. Une interprétation appropriée de ces symboles vous permettra d'utiliser l'outil de façon plus efficace et plus sûre. Symbole Nom Désignation/Explication V Volts Tension (potentielle) ...

  • Skil 2372 - page 23

    Numéro de modèle 2362 Tension nominale 7.2 V Régime à vide n 0 0-500/min Chargeur 1619X03241 Tension nominale 120 V 60 Hz Temps de Charge 3- 5 heures Capacités maximales Capacité de la douille Queue hexagonale de 1/4 po avec gorge de blocage Perçage du bois 3/ 8 p o ( 10 mm ) Mét al d oux 1/4 po (6 mm) Tailles de vis 1/4 po (6 m m) -23- Des ...

  • Skil 2372 - page 24

    L’outil perceuse/tournevis sans cordon Skil modèle 2362 possède une bague pouvant recevoir uniquement des queues hexagonales standard de 1/4 po avec gorge de blocage. La capacité bas régime de ce modèle ne constitue pas une lacune. Au contraire, le bas régime signifie un couple élevé et le couple élevé est un avantage très net pour per ...

  • Skil 2372 - page 25

    Vous prolongerez la durée de vos forets et accomplirez un travail plus net si vous mettez toujours le foret en contact avec le matériau avant d’appuyer sur la gâchette. Durant le fonctionnement, tenez l’outil fermement et exercez une pression légère et constante. Une trop grande pression à basse vitesse bloquera l’outil. Une pression in ...

  • Skil 2372 - page 26

    -26- FIXATION À L’AIDE DE VIS La procédure illustrée à la Fig. 6 vous permettra de fixer des matériaux ensemble à l’aide de votre perceuse/tournevis sans cordon sans dénuder, fendre ni séparer le matériau. Fixez d’abord les pièces ensemble à l’aide d’une bride, et percez le premier trou aux 2/3 du diamètre de la vis. Si le mat ...

  • Skil 2372 - page 27

    Numéro de modèle 2372 Tension nominale 7.2 V Régime à vide n 0 200/min Chargeur 1619X03241 Tension nominale 120 V 60 Hz Temps de Charge 3-5 heu res Capacités maximales Tige d'entraînement de l'embout Embouts de 1/4 po Capacité Boulons de 3/8 po Vissage dans le bois : Vis de 1/4 po Couple manuel 400 po/li v -27- Description fonction ...

  • Skil 2372 - page 28

    -28- (MODE MÉCANIQUE) INTERRUPTEUR/GÂCHETTE « MARCHE-ARRÊT » POUR METTRE L'OUTIL EN MARCHE, comprimez la gâchette. POUR ARRÊTER L'OUTIL, relâchez la gâchette, qui est à ressort et retournera automatiquement dans la position d'ARRÊT (Fig. 7). Le mode mécanique doit seulement être utilisé pour enfoncer des boulons et les ...

  • Skil 2372 - page 29

    Service IL N’EXISTE À L’INTÉRIEUR AUCUNE PIÈCE SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR. L’entretien préventif exécuté par des personnes non autorisés peut entraîner un positionnement erroné des composants et des fils internes, ce qui peut présenter de graves dangers. Nous recommandons de confier toute intervention d’e ...

  • Skil 2372 - page 30

    -30- Lea todas las instrucciones. Si no se siguen todas las instrucciones que aparecen a continuación, el resultado podría ser sacudidas eléctricas, incendio y/o lesiones graves. La expresión "herramienta mecánica" en todas las advertencias que aparecen a continuación se refiere a su herramienta mecánica alimentada por la red eléc ...

  • Skil 2372 - page 31

    -31- Si se proporcionan dispositivos para la conexión de instalaciones de extracción y recolección de polvo, asegúrese de que dichas instalaciones estén conectadas y se usen correctamente. El uso de estos dispositivos puede reducir los peligros relacionados con el polvo. Mantenga los mangos secos, limpios y libres de aceite y grasa. Las manos ...

  • Skil 2372 - page 32

    -32- Normas de seguridad para taladros/destornilladores sin cordón Sujete las herramientas mecánicas por las superficies de agarre aisladas cuando realice una operación en la que las herramientas de corte puedan entrar en contacto con cables ocultos. El contacto con un cable que tenga corriente hará que ésta pase a las partes metálicas descub ...

  • Skil 2372 - page 33

    -33- Normas de seguridad para llaves de apriete eléctricas inalámbricas Sujete las herramientas mecánicas por las superficies de agarre aisladas cuando realice una operación en la que las herramientas de corte puedan entrar en contacto con cables ocultos. El contacto con un cable que tenga corriente hará que ésta pase a las partes metálicas ...

  • Skil 2372 - page 34

    Cuidado de las baterías Cuando las baterías no están en la herramienta o en el cargador, manténgalas alejadas de objetos metálicos. Por ejemplo, para evitar que las terminales hagan corto- circuito, NO ponga las baterías en una caja de herramientas o en un bolsillo con clavos, tornillos, llaves, etc. Se pueden producir un incendio o lesiones. ...

  • Skil 2372 - page 35

    -35- Eliminación de las baterías – 2362 INSTRUCCIONES DE REMOCIÓN DE LA BATERÍA Haga funcionar el motor hasta que la batería esté completamente descargada antes de intentar sacarla de la herramienta. 1. Quite los siete (7) tornillos de la caja protectora con un destornillador de hoja plana. 2. Quite la tapa de la caja protectora levantándo ...

  • Skil 2372 - page 36

    -36- Símbolos IMPORTANTE: Es posible que algunos de los símbolos siguientes se usen en su herramienta. Por favor, estúdielos y aprenda su significado. La interpretación adecuada de estos símbolos le permitirá utilizar la herramienta mejor y con más seguridad. Símbolo Nombre Designación/explicación V Volt Tensión (potencial) A Ampere Corr ...

  • Skil 2372 - page 37

    Número de modelo 2362 Tensión nominal 7,2 V Velocidad sin carga n 0 0-500/min Cargador 1619X03241 Tensión nominal 120 V 60 Hz Tiempo de carga 3-5 hora s Capacidades máximas Capacidad del portaherramienta Cuerpo hexagonal de 1/4" con ranura de fijación Taladrado de madera (10 mm) 3/8" Metal suave (6 mm) 1/4" Tamaños de tornillo ...

  • Skil 2372 - page 38

    -38- Instrucciones de funcionamiento El taladro/destornillador sin cordón modelo 2362 de Skil tiene un mandril que acepta solamente accesorios con cuerpo hexagonal de 1/4" estándar con ranura de fijación. La capacidad de RPM baja de este modelo no es una deficiencia. Al contrario, velocidad baja significa par motor alto y el par motor alto ...

  • Skil 2372 - page 39

    Usted prolongará la vida de las brocas y realizará un trabajo mejor ejecutado si siempre pone la broca en contacto con la pieza de trabajo antes de apretar el gatillo. Durante el funcionamiento, sujete firmemente la herramienta y ejerza una presión ligera y uniforme. Una presión excesiva a baja velocidad hará que la herramienta se detenga. Una ...

  • Skil 2372 - page 40

    SUJECION CON TORNILLOS El procedimiento mostrado en la fig. 6 le permitirá sujetar unos materiales a otros atornillándolos con el destornillador sin cordón sin desforrar, rajar ni separar el material. Primero, fije las piezas una a otra y taladre el primer agujero con 2/3 del diámetro del tornillo. Si el material es blando, taladre únicamente ...

  • Skil 2372 - page 41

    -41- Número de modelo 2372 Tensión nominal 7,2 V Velocidad sin carga n 0 200/min Cargador 1619X03241 Tensión nominal 120 V 60 Hz Tiempo de carga 3-5 horas Capacidades máximas Accionador de salida Accionador de 1/4" Capacidad de perno 3/8" Apriete de tornillos en madera: Tornillos de 1/4" Par de giro manual 400 pulg.-lb Descripci? ...

  • Skil 2372 - page 42

    -42- (MODO ELÉCTRICO) INTERRUPTOR GATILLO DE "ENCENDIDO Y APAGADO" PARA ENCENDER LA HERRAMIENTA, apriete el interruptor gatillo. PARA APAGAR LA HERRAMIENTA, suelte el interruptor gatillo, que está accionado por resorte y regresará automáticamente a la posición de "APAGADO" (Fig. 7). El modo eléctrico está diseñado solame ...

  • Skil 2372 - page 43

    Mantenimiento Servicio NO HAY PIEZAS EN EL INTERIOR QUE PUEDAN SER AJUSTADAS O REPARADAS POR EL USUARIO. El mantenimiento preventivo realizado por personal no autorizado pude dar lugar a la colocación incorrecta de cables y componentes internos que podría constituir un peligro serio. Recomendamos que todo el servicio de las herramientas sea reali ...

  • Skil 2372 - page 44

    1619X03291 05/08 Printed in China L IMITED WARRANTY OF SKIL CONSUMER PORTABLE, BENCHTOP AND HD AND SHD HEAVY DUTY POWER TOOLS Robert Bosch Tool Corporation ("Seller") warrants to the original purchaser only, that all SKIL consumer portable, benchtop and HD and SHD Heavy Duty power tools will be free from defects in material or workmanship ...

Manufacturer Skil Category Drill

Documents that we receive from a manufacturer of a Skil 2372 can be divided into several groups. They are, among others:
- Skil technical drawings
- 2372 manuals
- Skil product data sheets
- information booklets
- or energy labels Skil 2372
All of them are important, but the most important information from the point of view of use of the device are in the user manual Skil 2372.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Skil 2372, service manual, brief instructions and user manuals Skil 2372. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Skil 2372.

Similar manuals

A complete manual for the device Skil 2372, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Skil 2372 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Skil 2372.

A complete Skil manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Skil 2372 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Skil 2372, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Skil 2372, that we can find in the current document
3. Tips how to use the basic functions of the device Skil 2372 - which should help us in our first steps of using Skil 2372
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Skil 2372
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Skil 2372 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Skil 2372?

Use the form below

If you did not solve your problem by using a manual Skil 2372, ask a question using the form below. If a user had a similar problem with Skil 2372 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)